5.3 complete takeout
 

I pulled this from an '05 GMC 4x4. Mileage unknown. The harness is not cut anywhere. The DBW pedal, harness, and controller are included as well as the computer, stock manifolds, shorty hugger headers (center dump), AC compressor, power steering pump, original motor mounts, gen 3 to gen 1 motor mount adapters from advance adapters, radiator and fans, stock airbox, fusebox, generic inline fuel pump (same as walbro 255), AN fittings and connections, high pressure fuel line, flywheel, and clutch.

I bought this to put in my truck, but ended up going a different route. You'll have everything you need to run this engine except for the corvette filter/regulator. The only modifications were to the computer and the flexplate/flywheel. I had the computer reprogrammed for a manual transmission and had the VATS, emmisions, and post cat 02 sensors deleted. The flexplate was removed, and I installed the sachs flywheel along with a standard 12" clutch (the flywheel is drilled for both new and old clutches) with a 10 spline disc (I was planning on running a, NV4500, but this setup up will work with anything from an SM420 to a muncie to a t56). I followed this thread to put together everything for the manual trans:
http://ls1tech.com/forums/conversion...-ls-motor.html

See below for prices

Re: 5.3 complete takeout
 

pics

Re: 5.3 complete takeout
 

Split up the prices look like so

Engine only SOLD
Uncut unmolested harness SOLD
The DBW pedal, harness, and controller SOLD
ECM/PCM computer SOLD
Coils SOLD
stock exhaust manifolds $50
shorty hugger headers (center dump) SOLD
AC compressor SOLD
power steering pump SOLD
original motor mounts SOLD
gen 3 to gen 1 motor mount adapters from advance adapters SOLD
radiator and fans SOLD
stock airbox SOLD
fusebox SOLD
generic inline fuel pump (same as walbro 255) $75
AN fittings and connections SOLD
high pressure fuel line SOLD
flywheel SOLD
clutch SOLD

Re: 5.3 complete takeout
 

Does the headers have the collectors included?

Re: 5.3 complete takeout
 

Are these what you mean?

Re: 5.3 complete takeout
 

ncut unmolested harness $150
The DBW pedal, harness, and controller $50
ECM/PCM computer $75

I would like all of this. Would you do a package deal?

Re: 5.3 complete takeout
 

Not cutting any deals yet, but check back next week, and I'll let you have it for $275 + shipping. I'm hoping someone just buys the whole setup.

Re: 5.3 complete takeout
 

It's okay I don't need a deal, but I do need all of that, so I will still take them if your willing to separate.

Re: 5.3 complete takeout
 

I will check back next week lol sorry about that

Re: 5.3 complete takeout
 

What year truck was thos going in in looking for some headers i have a set or truck manis on mine but there at a weird angle and dont want to get turned down when i take it to the exhaust shop

Re: 5.3 complete takeout
 

I was planning on using them on a '63, and I think they would have fit. They really do "hug" the block as you can see in the pics.

Re: 5.3 complete takeout
 

Let me crawl under my truck tomorrow after work to compare the pics u posted and see if it will fit if they do ill be more then happy to take them off ur hands :)

Re: 5.3 complete takeout
 

I will take engine please pm me info I can pick up locally thank you

Re: 5.3 complete takeout
 

does it come as pictured minus clutch flywheel and headers?

Re: 5.3 complete takeout
 

I think there going to be too tight for my application bud that starter looks awfully close to the collectors sorry tp disapoint

Re: 5.3 complete takeout
 

No problem Chuy

team adams,
Correct, engine is $500 as pictured minus the headers clutch and flywheel

Re: 5.3 complete takeout
 

Engine sold

Re: 5.3 complete takeout
 

This is all I have left currently

stock exhaust manifolds $50

original motor mounts $25



generic inline fuel pump (same as walbro 255) $60

Re: 5.3 complete takeout
 

Do you have the clutch and flywheel?

Re: 5.3 complete takeout
 

Already sold the clutch and flywheel. Sold the radiator and fans as well.

Possible to get a couple pics of the motor mounts? I might have a use for them. Thanks!



Posted via Mobile Device

Re: 5.3 complete takeout
 

Oh man, I haven't updated this in a while. I'm down to three parts left. Here's a link to the CL ad for the mounts that I still have.
http://beaumont.craigslist.org/pts/5690627195.html

Re: 5.3 complete takeout
 

You mean there is a market for these!

Re: 5.3 complete takeout
 

Probably not, I still have those and the stock truck manifolds, but you never know. Sometimes people come out of the woodwork and buy random stuff from you.

Re: 5.3 complete takeout
 

Actually, I think I can use them..PM sent