‘62 Long Low Fleet
 

I have not done a good job of taking pictures, let alone compiling them over the years with previous OT projects so I figure if I start a build thread, that might change things. Picked this truck up over the winter and have been anxiously waiting to tear into it as I finished up other more pressing projects. Finally drug it into the shop two weeks ago and have made some good progress so far.

Attachment 1675986
Attachment 1675990

Knowing that the rear was going to be more difficult to lower, I started there and will match that drop up front. Off with the bed and removed the 10 bolt

Attachment 1675991

Re: ‘62 Long Low Fleet
 

Got the notch boxed in and the 12 bolt mocked up. I’ll plate the notch once I decide if I need to keep the bump stop brackets and figure out a location for the shocks

Attachment 1675993

Pulled the seat and hump to extract the 4 speed through the floor then pulled the motor.
The front cross member was next to go.

Attachment 1675994
Attachment 1675995
Attachment 1675996

Re: ‘62 Long Low Fleet
 

Good progress! Looks like our plans are very similar for our 62's. I've swapped in a new front crossmember and want to pull the bed and notch the frame. Keep it up!

Re: ‘62 Long Low Fleet
 

Final plans?

Re: ‘62 Long Low Fleet
 

End game includes a 383, TKO600 and a Truetrac. The interior will get cleaned up with a new seat and carpet. I don't have intentions of doing any body work or paint. I'll need to raise the bed floor because of the notch and maybe make more room for wider rear tires.

Re: ‘62 Long Low Fleet
 

Here is my '62 shock location. If stock arms the rear push forward as it goes up. Use blocks to help. Mine is a pipe notch bit you looking to lay frame?

Re: ‘62 Long Low Fleet
 

Update from the last few weekends. Finished up the rear suspension. Installed rear bags, fabricated upper and lower shock mounts, made brackets for the panhard bar. I still need to finish weld the trailing arm brackets and panhard but I'll wait until i get the trans installed and know what my pinion angle needs to be.
Attachment 1685184
Attachment 1685185

Got it all squared up and sitting on 4 wheels again.
Attachment 1685186

Re: ‘62 Long Low Fleet
 

Almost forgot, finished the front end swap ('84).
Installed the steering shaft and box with CaptainFab's kit
Attachment 1685336

Attachment 1685337

Attachment 1685338

Re: ‘62 Long Low Fleet
 

Looks good. I plan on swapping the front end and rearend of a 82 into my 62.

Re: ‘62 Long Low Fleet
 

Nice work so far. Welcome

Re: ‘62 Long Low Fleet
 

Back to work on the truck. Got the bed sitting on the frame once again.

Attachment 1698378

Started to work on raising the floor. Couldn't find many pictures (thanks photobucket) on how others have done it so this is what i came up with.

Attachment 1698380

I welded 1x1 angle around the perimeter so the flooring will mount similar to the original. Notch is 4" so i just used 2x4 tubing where it mounts to the frame. Building the area up at the tailgate is next.

Attachment 1698379

Re: ‘62 Long Low Fleet
 

Made a bit more progress recently. Got the tailgate area of the floor sorted out. Used 4 different pieces to create a shape that was close to stock design

Attachment 1718059
Attachment 1718060

I sectioned the wheel wells a few inches so the proportions look better with the shallower bed.

Attachment 1718061
Attachment 1718062

I'm going to hold off on the wood until the truck is on the road. Having access from above is priceless.

Re: ‘62 Long Low Fleet
 

Very nice build. I have been looking for a way to raise my bed. Hope you don't mind if I use your ideas. Will follow your progress.

Re: ‘62 Long Low Fleet
 

Would you mind to pm me some more info on the power steering install? I’ve got a 62 as well and about to do that same thing, without instructions or measurements. Awesome build!

Re: ‘62 Long Low Fleet
 

Got back to work on the truck after collecting parts during the colder months and taking care of things around the house this spring.

Borrowed an old block for mock up which allowed me to make the engine and trans mounts.

Attachment 1794251

Attachment 1794253

That also allowed me to figure out my pinion angle so the trailing arm brackets could be welded up. Pulled the rear end and loaded it with goodies. 4.10 gears, a TrueTrac and new brakes.

Attachment 1794246

Finish welded the trailing arm and track bar brackets before installing the axle permanently.

Re: ‘62 Long Low Fleet
 

Lookin' great! :ito:

Re: ‘62 Long Low Fleet
 

Also got the exhaust from the cab back fabricated. Ill finish the front half once the motor/headers are installed.

Attachment 1794447

Attachment 1794448

Got a rear sway bar from Performance Online. Might have to shorten up the end links a little more as they hang down a little further than i like

Attachment 1794449

Been trying to figure out a way to utilize the forward pedal pivot point and i think i got it. Used a second set of pedals and some rod ends to connect the two. The master cylinder push rods still connect in the original location so there are no issues with angle or arch. I can move the rod ends up or down to manipulate the pedal ratio to dial it in once i get it on the road. Pedals are now lower and push more towards the floor not the firewall

Attachment 1794450

Re: ‘62 Long Low Fleet
 

Looks like you've been doing good work!

Re: ‘62 Long Low Fleet
 

So this will sound like a terribly basic question . . . is there anyway you could identify the bolts you had to remove to get the bed off? I will need to pull my bed also, and have no idea which bolts actually hold the bed to the chassis . . .
Thanks -
Doug

Re: ‘62 Long Low Fleet
 

The big day finally arrived! Took a road trip to meet up with the father in law and load the motor that I've been waiting on for what seems like eternity.

Attachment 1804352

Dropped it in the hole and ordered everything needed to start making noise. Should be busy for the next few weeks throwing parts at it as they come in

Attachment 1804353

Re: ‘62 Long Low Fleet
 

Start up is always a milestone, what's the motor Stock? Mild? or Hot?

Re: ‘62 Long Low Fleet
 

.30 over, flat tops, big cam, RHS heads, solid lifters and roller rockers. Not what we had originally planned but its the only way i stand a chance of getting it on the road before summer is over.

Re: ‘62 Long Low Fleet
 

Hot Rod truck...a man after my own heart lol. I love the old hot rod trucks...sounds like you are in for a good time...I'll be watching:smoke:

Re: ‘62 Long Low Fleet
 

Any chance you made patterns for the notch you might consider sharing? I have a 62 also, and your notch looks awesome!
Thanks,
Doug

Re: ‘62 Long Low Fleet
 

Thanks....I didn't save any patterns but if you PM me your email address, I'll trace the plate and send it to you