Re: My 1968 C-20 Golden Anniversary Project
 

THANKS DALE!

Found out that the NOS flame arrestor #3857476 is wrong- too big, see picture. Fortunatly I have a complete set from our fellow ROOGER KOOP here in the forum.

Re: My 1968 C-20 Golden Anniversary Project
 

FOUND THE RIGHT FITTINGS FORE THE OIL PRESSURE GAUGE AND VACUUM GAUGE INSTALLATION.

NAPA 302X2, 6200X2, 6100X2
LMC truck 36-1923 Oil Pressure Tube Kit-49", 31-3406 Vacuum fitting-Tee-Barbed,31-3404 Barbed Fitting-Gauge

Bolts Air intake Manifold: ARP 134-2001

Re: My 1968 C-20 Golden Anniversary Project
 

Preparing Water outlet, found out that my manifold despite the same casting number as the original has not the hole for cooling water (connection to pump), therefore I try the riser (thermostat above the opening for the hole)

Re: My 1968 C-20 Golden Anniversary Project
 

Some more pictures:

Gasket FEL-2202
Vintage Air water Neck Riser VTA-706001-VCQ
Water outlet four seasons 84820
Thermostat: Mr Gasket #4365 195° Fahrenheit (90.5° C)

Re: My 1968 C-20 Golden Anniversary Project
 

Further manifold accessories:
Vacuum fitting (for power brake, heating/air condition reservoir & transmission TH400, spigott must be inside the fitting.

Distributor fittings

Re: My 1968 C-20 Golden Anniversary Project
 

Rockerarm Kit SUM -G6800 1.5 Ratio, Fits 3/8" studs

Hydraulic lifter Federal Mogul HT-817

Engine Mount screws totally stainless 6-2259

Re: My 1968 C-20 Golden Anniversary Project
 

Temperature sending unit: 01513321

Preparing exhaust manifolds #3896956 #3855163

Exhaust Manifold LH (Driver): 3855163 L.H (Cast 8155163A or 3855163A), interchangeable 387241
Exhaust Manifold RH (Passenger): 3896956 R.H. (discontinued use 3905364 or 3932469)

Preparing some measurements camshaft degreeing

Re: My 1968 C-20 Golden Anniversary Project
 

Oil dip stick Kit PRO-66116

Some pictures regarding exhaust gas mainifold heat shields

Re: My 1968 C-20 Golden Anniversary Project
 

Amazing work Gerhard! You're going to have the nicest C10 in all of Germany:chevy::metal:;):smoke:

Re: My 1968 C-20 Golden Anniversary Project
 

Last entry from 10-18-2020, 04:56 PM , was completly frustrated, because of the not matching valve timings (tested with Summit Degree Wheel), after studing and learning alot now new hope, start soon.

Re: My 1968 C-20 Golden Anniversary Project
 

Goodness, you're getting technical. I'm glad to see you're still around....

Re: My 1968 C-20 Golden Anniversary Project
 

Hobby is gone, truck sold, was a nice time here in the forum

Re: My 1968 C-20 Golden Anniversary Project
 

Noooo! Say it isn’t so. Call it temporary, leave the door open just in case another truck happens to cross your path.

Re: My 1968 C-20 Golden Anniversary Project
 

Oh man, hadn't seen this build before, was just getting into it. I've never seen such detailed care taken in engine assembly. Good luck Gerhard. Sorry to hear that you sold it, but sometimes that has to happen. Hope to see you back. It looks like you got it all together. How did it run?

Re: My 1968 C-20 Golden Anniversary Project
 

You can still stop in Gerhard.

Re: My 1968 C-20 Golden Anniversary Project
 

I'm surprised! What's the next project Gerhard?

Re: My 1968 C-20 Golden Anniversary Project
 

I JUST came across this thread.

I knew this was going to happen :(

I gave, made, sold many parts to Gerhard and tried to give him a lot of common sense advice but being a German engineer he was determined to complicate the living dung out of everything.

I always wondered if he'd frustrate himself into packing it in which looks like finally happened - so sorry , too bad :(

Jerry in Canada