Edelbrock Torker 2R -Square Port BBC Manifold
3 Attachment(s)
Not sure of the age. Removed from my '69 396 oval head motor 10 years ago.
Big block, square port, single plane manifold. Looks to be in good shape aside from needing a bath. 50$ + the ride if shipped. Local pickup / meet up possible in the Bay Area. |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Can you post pictures of the gasket surfaces, both sides???
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
I will take it if the surfaces are OK. The water crossover area can get a lot of corrosion on it...
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Sorry, I would have to have it shipped...
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Sorry, can't get used to not getting notifications. I'll get some pics tonight. IIRC, the surfaces were pretty clean.
Sorry for the lag. |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
THe biggest concern is where the intake gasket seals to the head. Sometimes the intakes get very corroded there...
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
5 Attachment(s)
Really sorry for the delay. Here are some pics. Couldn't get the camera to focus really close up. Crossover looks fine. Little to no corrosion. Some rust staining inside but no pits. The cooling jacket block offs at the rear have a little pitting which really doesn't show up well in the closeups. I can take some measurements if you'd like.
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Might take a couple more pictures of second photo from top...other side looks good.
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
2 Attachment(s)
New phone, better camera. Let's see how these look.
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
I will take it!!!
I don't do paypal. PM me how I need to pay you. Can send check or money order I need to know how you will ship. I send US Postal stuff to my house, Brown or Fedex to my work. Thanks Jeff |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Hey Jeff, I started messing around with it last night and noticed that the hose barbell that goes to the water pump had what looked like silicone. Tried removing the fitting with a wrench and it wouldn't budge so I gave it a little heat and it popped loose to reveal 1/2 of the threads missing. The silicone turned out to be JB weld.
I'm going to pull the listing tomorrow until I figure out what to do with it. Last thing I want to do is sell someone a bunk part. Sorry for the inconvenience. |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
1 Attachment(s)
Pic
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Take another picture, showing how far deep the threads go, in the hole. I may still take it...
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Will do Jeff
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
1 Attachment(s)
So the threads are 1/2" deep and about a 1/4" missing. Please excuse the makeshift ruler. It's fairly accurate though.
All other threaded holes are fine. Not sure how shipping would work right now either. All 5 surrounding counties on some form of lockdown. Essential services are the only thing that are open. Maybe USPS at this point. |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
I will take it. I am in NO hurry to get it...
Post 10 has my comments on shipping. I will PM you my 2 address for shipping... |
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Sounds good Jeff. I will get a ship quote asap and will PM you. It might take a minute as things are a bit arse over tea kettle these days. I have no idea if the brown store here is even open. Ill do my best to get out there tomorrow.
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Get a quote, maybe even 2 quotes, I can send the funds, then you can send when it's possible. I'm in no hurry...however long it takes...
|
Re: Edelbrock Torker 2R -Square Port BBC Manifold
Sold!
|
All times are GMT -4. The time now is 04:25 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com