How much did your driveshaft cost? When?
I am changing transmissions and have a two piece driveshaft. The rear piece was recently made before I bought the truck and looks "new".
I need the original untouched front shaft remade from scratch. I have only one place in my town that makes them and they quoted me ~$550 to remake the front shaft from scratch using my measurements. Does this sound about right? |
Re: How much did your driveshaft cost? When?
When I went to a one piece drive shaft in my 71 short bed it was $330 for everything new in 11-18-2020.
I had rear drive shaft made for my 4x4 and the front shortened and rebuilt for $744 in 5-18-2022. |
Re: How much did your driveshaft cost? When?
Apples to oranges, but -- I had a new rear driveshaft made for my K20 for $634. The original shaft mysteriously got bent when the body shop had the truck.
|
Re: How much did your driveshaft cost? When?
Not quite the same but purchase price and options offered for comparison.
One piece Driveshaft for SWB 72 C10 LS with T 56 Magnum 6 speed purchased last May 2022, With upgrade to 1350 yokes and joints . Purchased from Silver Sport Transmissions. Built and drop shipped by Dynotech Driveshafts. Clawson,MI $568.00 shipped |
Re: How much did your driveshaft cost? When?
I really appreciate your input folks. It sounds like from scratch, it might be a fair price.
I'm gonna call a few shops in Los Angeles tomorrow and see what they can do for me, the gas would only be $100, but I'd have to take a day off. Probably outta just have them do it here in town.... |
Re: How much did your driveshaft cost? When?
I paid $550 from actionmachineinc.com in Dec 2021 for a 1 piece shaft
Sonnax T3-3-2431HP Trans Slip Yoke × 1 $154.59 Custom Driveshaft - Aluminum, 3.5" OD, 1350 Series × 1 $395.46 Subtotal $550.05 |
Re: How much did your driveshaft cost? When?
Driveline service Fresno
I was quoted $300- 57in 3in tube 1330 yoke U joints and balance |
Re: How much did your driveshaft cost? When?
Quote:
I had both shafts, say 2018. They balanced them, installed a new carrier bearing and U-joints, $450ish. $550 doesn't surprise me, does that include balance? |
Re: How much did your driveshaft cost? When?
Do you need a new driveshaft or just to shorten one? September 2020 I paid $160 to shorten an aluminum driveshaft plus 2 genuine Spicer U-joints.
|
Re: How much did your driveshaft cost? When?
Quote:
|
Re: How much did your driveshaft cost? When?
Just received two CV drive shafts for my K10 project from Carolina driveline. About $1,500 shipped, little over two weeks. Was disappointed they did not clearance the front CV for more angle as I was told they would do. Originally ordered from High Angle Driveline because he makes some specailized CV joints, but Jess there thinks he has an indefinite time to ship. His prices are double, almost 3k. No problem with paying more for a unique product but gave up after 4 months with him. Left a review in the vendors section.
If ordering again online I would use Tom Woods, will ship within 24 hours and would guess a standard two ujoint shaft will be $300-$500. |
Re: How much did your driveshaft cost? When?
Quote:
|
Re: How much did your driveshaft cost? When?
Seems a little high for a front shaft . I haven't had one done but I did replace my 2 piece shaft on my dodge with a one piece 5 inch aluminum shaft from Action Machine in South Bend Indiana for under 800. I'm having them make up a new driveshaft for my Chevell with 1350 ujoint when I upgrade my transmission
|
Re: How much did your driveshaft cost? When?
Original 2 piece driveshaft off my 68 C10 Longbed, they replaced the short front portion, installed new spicer u joints, balanced — cost $550 in Tampa Fl. Timing December 2022.
|
Re: How much did your driveshaft cost? When?
Last year I converted to a one piece for my long bed (4" steel) with 1350 spicer u-joints for $350. It was a truck supplier company ("Fleet Pride"-I think they are a national chain)....it was loads cheaper then the "hot-rod" shops who make driveshafts online.
|
Re: How much did your driveshaft cost? When?
One piece drive shaft for my Burban from Tom Woods Custom Drivelines was $329 in July of 2020.
|
Re: How much did your driveshaft cost? When?
Sounds like a long one piece is much cheaper than a 2 piece.
|
Re: How much did your driveshaft cost? When?
Quote:
|
Re: How much did your driveshaft cost? When?
just had mine done earlier in the year. stock 2 piece, rear section was shortened and a slip shaft added. about $550 with new u joints and carrier bearing
|
Re: How much did your driveshaft cost? When?
Quote:
I'll post what I pay as soon as I get it back. |
Re: How much did your driveshaft cost? When?
Quote:
|
Re: How much did your driveshaft cost? When?
Paid $600 + This year @ Inland truck centers 1 pc drive shaft 2.5 in diameter.
|
All times are GMT -4. The time now is 06:16 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com