|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-18-2016, 03:45 AM
|
#1 |
|
Registered User
Join Date: Feb 2016
Location: Kemmerer
Posts: 84
|
3 speed manual to T-400 conversion trans yoke?
I have put a T-400 auto trans in place of the 3 speed manual and everything is bolted in but the drive shaft. It is measured, shortened and balanced ready for install. I will need a cross-over u-joint until i can swap the yoke. Does anyone know the part number or ID on this u-joint?
|
|
|
|
09-18-2016, 07:26 AM
|
#2 |
|
Registered User
Join Date: Apr 2008
Location: Md
Posts: 2,454
|
Re: 3 speed manual to T-400 conversion trans yoke?
I got mine from Denny's Drive shafts.http://www.dennysdriveshaft.com/c142...32_x_3_58.html
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=635605 |
|
|
|
|
09-18-2016, 02:37 PM
|
#3 |
|
Registered User
Join Date: Feb 2016
Location: Kemmerer
Posts: 84
|
Re: 3 speed manual to T-400 conversion trans yoke?
Thank YOU! This saves a lot of fuss!
|
|
|
|
|
09-19-2016, 09:39 PM
|
#4 |
|
Senior Member
 
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 6,235
|
Re: 3 speed manual to T-400 conversion trans yoke?
What do you mean swap the yoke? On the diff?
__________________
70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear |
|
|
|
|
09-20-2016, 10:56 PM
|
#5 |
|
the boat guy
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
|
Re: 3 speed manual to T-400 conversion trans yoke?
If it doesn't have the tranny yoke on it, it isn't balanced..
You need to figure out what kind of ujoint the tranny yoke is and what kind of ujoint the driveshaft is (probably 1310) should have had the driveshaft shop put the right weld yoke in the driveshaft that matches the tranny yoke.
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project, |
|
|
|
|
09-21-2016, 12:03 AM
|
#6 | |
|
Registered User
Join Date: Feb 2016
Location: Kemmerer
Posts: 84
|
Re: 3 speed manual to T-400 conversion trans yoke?
Quote:
|
|
|
|
|
|
09-21-2016, 12:05 AM
|
#7 | |
|
Registered User
Join Date: Feb 2016
Location: Kemmerer
Posts: 84
|
Re: 3 speed manual to T-400 conversion trans yoke?
Quote:
|
|
|
|
|
|
09-22-2016, 01:31 PM
|
#8 | |
|
the boat guy
Join Date: Jul 2007
Location: springfield mo
Posts: 2,339
|
Re: 3 speed manual to T-400 conversion trans yoke?
Quote:
If you change transmission yokes you change the balance of the divshaft even if you use a conversion joint... or even if you use the original joint. If you're able to measure the ujoint I can give you part numbers or even sell you one. But even if your but dyno doesn't feel a vibration that doesn't mean that you aren't risking damage to the transmission. Its best just to do it right the first time.
__________________
67, swb, fleet, tach, throttle, 5.3, 4l60e, 3.73's, fuel cell, 5 lug, p.d.b., 4-6 drop. great little truck 66, stevens drag/ski 18' silouette, 350, 2.02 doublehump heads. comp extreme marine 278 cam, vette 7 fin valve covers, old polished edelbrock intake, velvetdrive, casale v-drive, adj cavitation plate. 28, model a rpu project, |
|
|
|
|
|
09-23-2016, 12:31 PM
|
#9 |
|
Registered User
Join Date: Feb 2016
Location: Kemmerer
Posts: 84
|
Re: 3 speed manual to T-400 conversion trans yoke?
Thank you!
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
