TX WTB Inline Fuse Holder - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Erl · 12-19-2011, 03:46 PM

Broke the metal connector inside the rubber fuse holder trying to get it apart to re-tape the wiring harness. It is located up near the battery box in the engine bay wiring harness on my 68 GMC. Anyone know where to get a new one or have a used one for sale.

Erl

JimKshortstep4x4 · 12-19-2011, 08:52 PM

Do you need both ends?

I will check tomorrow as I may have what you need.

Jim

Erl · 12-20-2011, 10:05 AM

Yes, I need both ends with enough wire so I can splice them in. They break pretty easy when you take them apart. They have been together for over 40 years.

Erl

JimKshortstep4x4 · 12-20-2011, 12:41 PM

I don't have both ends that are not part of a good harness. I have the large end if you can use it. It is in good condition and has 4" of pigtail on it. If you want it just cover the postage and I will be glad to send it to you.

I am curious as to why yours broke as I have only broken the fuses in the dozens that I have taken apart over the years.

Jim

Erl · 12-20-2011, 12:46 PM

I twisted it, trying to get it apart. The clips were bonded to the fuse on both ends and the clips sheared off down inside. Once it was apart I understood what had happened. Thanks for the offer, but I need both ends.

Erl

teeitup · 12-20-2011, 01:20 PM

Erl, I think I have some out there if I can find them. I cut them off harnesses before I took the copper to scrap. I'll look Wed after work

Thanks Randy

Erl · 12-20-2011, 01:55 PM

Randy, you were my next Email. I figured you had a few of these. I am also needing a muffler support as shown below.

JimKshortstep4x4 · 12-20-2011, 08:32 PM

Erl,

I looked through my miscelaneous wire collection again and found the other end, (my miscelaneus wire collecion looks like 2' hair ball). There is a 4" pigtail on the large end and a 2' pigtail on the small end.

Anyway, if you still need the parts you can have both for postage.

JIm

teeitup · 12-20-2011, 09:12 PM

Erl, sorry none of those brackets right now. Looks like Jim has you set up for the wiring, if you need one with a bit longer wire let me know and I'll get it in the mail. Thanks Randy

12-19-2011, 03:46 PM	#1
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	WTB Inline Fuse Holder Broke the metal connector inside the rubber fuse holder trying to get it apart to re-tape the wiring harness. It is located up near the battery box in the engine bay wiring harness on my 68 GMC. Anyone know where to get a new one or have a used one for sale. Erl Attached Images __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

12-19-2011, 08:52 PM	#2
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: WTB Inline Fuse Holder Do you need both ends? I will check tomorrow as I may have what you need. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-20-2011, 10:05 AM	#3
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	Re: WTB Inline Fuse Holder Yes, I need both ends with enough wire so I can splice them in. They break pretty easy when you take them apart. They have been together for over 40 years. Erl __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

12-20-2011, 12:41 PM	#4
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: WTB Inline Fuse Holder I don't have both ends that are not part of a good harness. I have the large end if you can use it. It is in good condition and has 4" of pigtail on it. If you want it just cover the postage and I will be glad to send it to you. I am curious as to why yours broke as I have only broken the fuses in the dozens that I have taken apart over the years. Jim __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-20-2011, 12:46 PM	#5
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	Re: WTB Inline Fuse Holder I twisted it, trying to get it apart. The clips were bonded to the fuse on both ends and the clips sheared off down inside. Once it was apart I understood what had happened. Thanks for the offer, but I need both ends. Erl __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

12-20-2011, 01:20 PM	#6
teeitup Just like to part out trucks!! Join Date: Nov 2001 Location: Meriden, Ks-North of Topeka 10 miles Posts: 27,396	Re: WTB Inline Fuse Holder Erl, I think I have some out there if I can find them. I cut them off harnesses before I took the copper to scrap. I'll look Wed after work Thanks Randy __________________ 67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure"

12-20-2011, 01:55 PM	#7
Erl Registered User Join Date: Mar 2002 Location: Dallas, TX Posts: 555	Re: WTB Inline Fuse Holder Randy, you were my next Email. I figured you had a few of these. I am also needing a muffler support as shown below. Attached Images __________________ 1968 GMC 305 V6 3/4 4x4 Stepside 06 Corvette Daily Driver Dallas TX

12-20-2011, 08:32 PM	#8
JimKshortstep4x4 Senior Member Join Date: Jul 2001 Location: Muskegon,MI,USA Posts: 6,026	Re: WTB Inline Fuse Holder Erl, I looked through my miscelaneous wire collection again and found the other end, (my miscelaneus wire collecion looks like 2' hair ball). There is a 4" pigtail on the large end and a 2' pigtail on the small end. Anyway, if you still need the parts you can have both for postage. JIm __________________ 1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC

12-20-2011, 09:12 PM	#9
teeitup Just like to part out trucks!! Join Date: Nov 2001 Location: Meriden, Ks-North of Topeka 10 miles Posts: 27,396	Re: WTB Inline Fuse Holder Erl, sorry none of those brackets right now. Looks like Jim has you set up for the wiring, if you need one with a bit longer wire let me know and I'll get it in the mail. Thanks Randy __________________ 67 Chev swb stepside 4x4 283 4 speed SOLD 72 blazer 4x4 4 speed Cheyenne 72 GMC swb 4x4 fleet 4 speed, original paint 1958 Cameo (one of 1405 built, it was my dads) 2020 chevy Apex 4x4 crew cab 1969 Z28 with the 302 1980 chevy swb 4x4 1964 chevell Malibu SS 1976 K20, sold new originally out of my dads chevy dealership Members that I've met, over 200 probably closer to 300 in the 12 years I've been on this site, everyone I met "It was a pleasure"



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.