|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-17-2012, 04:44 PM
|
#1 |
|
Registered User
Join Date: Apr 2003
Location: NB
Posts: 3,367
|
tightning castle nut when ball joint spins??
Help!! What is the trick to tighten the castle nut down on the ball joints when the ball joints spin with ease???????????
Stuck! 
__________________
1968 Chevy C10 307 3ott fleetside 1967 Chevy C/10 V8, 3spd, fleetside lwb.Sold 1967 Chev C/10 step, 383, M21. SOLD |
|
|
|
07-17-2012, 07:05 PM
|
#2 |
|
Registered User
Join Date: Jul 2011
Location: SW Ontario
Posts: 1,199
|
Re: tightning castle nut when ball joint spins??
Stick a drift in the cotter pin hole and use a wrench to tighten it, at some point it'll "stick" and you can proceed normally.
Alex. |
|
|
|
|
07-18-2012, 12:07 AM
|
#3 |
|
Registered User
Join Date: Dec 2007
Location: Southington CT
Posts: 548
|
Re: tightning castle nut when ball joint spins??
When I did mine I just used a jack under the arm and put some pressure on the ballpoint and caused it to friction wedge into the spindle
Posted via Mobile Device
__________________
68-SWB, 327, hooker headers, spintec mufflers, disk brake 3.5/5 drop, buddy buckets, 200-4R, 2200 stall, 3.73 12bolt Eaton Posi,  My 68-SWB Photo Build Thread All my Google Albums |
|
|
|
|
07-18-2012, 06:12 PM
|
#4 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,919
|
Re: tightning castle nut when ball joint spins??
We just had this happen on a 92 & I use oversized washers to overcome the problem.
Stack them high enough so that there is enough thread to engage the nut but also so that the BJ is immediately pulled into the spindle. It should snug up quickly & then take the nut back off, remove a couple of the washers & repeat until it's seated enough so that it doesn't spin. Pull any remaining washers & tighten to spec + install the cotter key.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
07-18-2012, 06:25 PM
|
#5 |
|
Registered User
Join Date: Aug 2007
Location: ozark, al
Posts: 583
|
Re: tightning castle nut when ball joint spins??
we had to use a puller and put the screw in part on the end of the ball joint, and pulled the pieces together kinda like a big clamp. be careful not to mess up the end of the ball joint.
|
|
|
|
|
07-18-2012, 09:31 PM
|
#6 |
|
Senior Member
Join Date: Apr 2000
Location: Delta,Pa
Posts: 14,950
|
Re: tightning castle nut when ball joint spins??
I normally use an impact gun. It spins fast enough to overcome the balljoint spinning. If you dont have an impact you need to pin the ball joint shaft into the spindle.
__________________
Owner of North Point Car Care in Dundalk Md. We specialize in custom exhaust on both modern and classic vehicles. We are a full service auto shop from classics to modern vehicles. Feel free to contact me with questions. I will give a 10% discount to any board member. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
