Computer mount pictures - The 1947 - Present Chevrolet & GMC Truck Message Board Network

softballnrd27 · 01-14-2016, 01:06 PM

Let see what you got. I built a mount for mine and now I am trying to decide where I want to mount it.

Aruba1 · 01-14-2016, 11:00 PM

Subscribed.

Can you post a pic of your mount? I am also trying to figure where to mount mine.

softballnrd27 · 01-15-2016, 10:42 AM

I will get a picture today when I get home.

Andy4639 · 01-15-2016, 10:56 AM

Do a site search, there are several of these threads already with pictures.

softballnrd27 · 01-16-2016, 12:10 AM

Quote:

Originally Posted by Andy4639

Do a site search, there are several of these threads already with pictures.

I did and got a bunch of engine mount threads.

softballnrd27 · 01-16-2016, 12:11 AM

Here are the pics of the mount I built now I just need to figure out where in the cab I am going to mount it.

65standard · 01-16-2016, 09:37 AM

I'm mounting the LSx computer in the same spot as the original 1985 ECU under the dash top. Using the same hole in the firewall for the harness to pass thru.

Andy4639 · 01-16-2016, 10:46 AM

Here are some links.

http://67-72chevytrucks.com/vboard/s...d.php?t=622555

http://67-72chevytrucks.com/vboard/s...d.php?t=401254

**nsb29** · 01-16-2016, 02:38 PM

no pic but its going under the seat passenger side

softballnrd27 · 01-18-2016, 01:43 AM

Here is what I have so far, I'm still trying to figure out where I'm going to mount it under the dash.

**Curtb1971** · 01-18-2016, 03:30 AM

Not sure if your application will work but hey might be useful to someone. Had to build a bracket for the DBW pedal so knocked out two birds with one bracket. Kept the throttle cable hole for the mechanical gauge oil line to pass through but filled the washer lines and rear harness holes. Made the plate out of 1/8" steel with a brake in it on the drivers side. Used the original gas pedal bolts and a small 90 degree brace screwed to the cab reinforcement bump out for support.

Trans controller. Took 1/4" 20 1 1/4" all thread and welded 1 1/4" fender washers to the end then ground flat to make a stud. I took these and used 3m panel bonding adhesive to glue them directly to the firewall after grinding the paint to bare metal. Did this to eliminate putting screws/hole through the firewall

Also glued some studs for the relays on the back side of the cowl gutter.

solidaxel · 01-18-2016, 10:13 AM

Good location for the controllers, where did you get the harness?

**Curtb1971** · 01-18-2016, 02:35 PM

The wiring Harness is from Howell Industries.

**GMC-YA68** · 01-18-2016, 09:21 PM

I saw where someone here mounted it inside the glove box and it looked pretty clean. Right now mine is on the pass side floor board up high along with my fuses /relays but I want to move it to the glove box once I put carpet in.

fast70swb · 01-19-2016, 02:51 PM

Curtb1971

What gas pedal is that from and what it work with a 2006 lq4 computer

'68 Newtricks · 01-19-2016, 03:43 PM

**Curtb1971** · 01-19-2016, 03:56 PM

Quote:

Originally Posted by fast70swb

Curtb1971

What gas pedal is that from and what it work with a 2006 lq4 computer

This is it from Pace Performance, not sure if it will work or not as I had to swap two wires around for a 2009 computer. I think if the connector is the same it should work, but again can't be positive.

fast70swb · 01-19-2016, 05:11 PM

Thank you I will check it out. I'm at the computer mounting and pedal install test fitting part of my build

izzy_Britton · 01-20-2016, 01:00 AM

Quote:

Originally Posted by nsb29

no pic but its going under the seat passenger side

sorry for the hijack:

HOW are you lengthening the wire harness to reach all the way under the seat? snip solder and heat shrink? any advice would be great.

Thanks

**nsb29** · 01-20-2016, 11:38 AM

Quote:

Originally Posted by izzy_Britton

sorry for the hijack:

HOW are you lengthening the wire harness to reach all the way under the seat? snip solder and heat shrink? any advice would be great.

Thanks

lay it out on a bench run your new or lengthened wiring in a loop and back to your ECM that way you cut and splice one wire at a time and a lot of patience if you PM me your cell I can send you pic Doug

LS64C10 · 03-02-2016, 06:07 PM

Here's a few of mine. I made a bracket to mount it behind the glove box at an angle so I could reuse the original liner for the glove box. The only thing you can see is the OBDII port.

Dustytrix · 03-02-2016, 10:31 PM

Great job LS64C10.

**truckdude239** · 03-02-2016, 11:47 PM

I used an 2003 zr2 s10 computer mount boltex to fendor wheel

izzy_Britton · 03-03-2016, 01:32 AM

Quote:

Originally Posted by truckdude239

I used an 2003 zr2 s10 computer mount boltex to fendor wheel

Spaghetti much? wow!

foamypirate · 03-03-2016, 02:06 AM

Quote:

Originally Posted by izzy_Britton

Spaghetti much? wow!

This comment adds nothing to the conversation. He is probably in the middle of the install...

01-14-2016, 01:06 PM	#1
softballnrd27 Always a work in progress Join Date: Jun 2007 Location: Harker Heights, TX Posts: 1,599	Computer mount pictures Let see what you got. I built a mount for mine and now I am trying to decide where I want to mount it. __________________ USMC Retired Never trust a man who can't laugh at his own fart! 2010 Silverado Crew Cab 73 SWB 5.3/4l80e Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=695168

01-14-2016, 11:00 PM	#2
Aruba1 Registered User Join Date: Apr 2014 Location: Birmingham, AL Posts: 560	Re: Computer mount pictures Subscribed. Can you post a pic of your mount? I am also trying to figure where to mount mine.

01-15-2016, 10:42 AM	#3
softballnrd27 Always a work in progress Join Date: Jun 2007 Location: Harker Heights, TX Posts: 1,599	Re: Computer mount pictures I will get a picture today when I get home. __________________ USMC Retired Never trust a man who can't laugh at his own fart! 2010 Silverado Crew Cab 73 SWB 5.3/4l80e Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=695168

01-15-2016, 10:56 AM	#4
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,936	Re: Computer mount pictures Do a site search, there are several of these threads already with pictures. __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

01-16-2016, 12:11 AM	#6
softballnrd27 Always a work in progress Join Date: Jun 2007 Location: Harker Heights, TX Posts: 1,599	Re: Computer mount pictures Here are the pics of the mount I built now I just need to figure out where in the cab I am going to mount it. __________________ USMC Retired Never trust a man who can't laugh at his own fart! 2010 Silverado Crew Cab 73 SWB 5.3/4l80e Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=695168

01-16-2016, 09:37 AM	#7
65standard Registered User Join Date: Dec 2014 Location: Coal City, IL Posts: 695	Re: Computer mount pictures I'm mounting the LSx computer in the same spot as the original 1985 ECU under the dash top. Using the same hole in the firewall for the harness to pass thru. __________________ Tony Nicholas @ Midwest Metal Masters 1953 Chevy 3100 392 Hemi w/727 & 9” Ford 1985 Chevy C/10 6.0L 4L80 373 locker

01-16-2016, 10:46 AM	#8
Andy4639 Old member Join Date: Jan 2002 Location: Liberty, & Garden City S.C. , U.S. Posts: 19,936	Re: Computer mount pictures Here are some links. http://67-72chevytrucks.com/vboard/s...d.php?t=622555 http://67-72chevytrucks.com/vboard/s...d.php?t=401254 __________________ 1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.

01-16-2016, 02:38 PM	#9
nsb29 Senior Member Join Date: Feb 2014 Location: new smyrna beach fl / 29 palms cal Posts: 1,727	Re: Computer mount pictures no pic but its going under the seat passenger side

01-18-2016, 01:43 AM	#10
softballnrd27 Always a work in progress Join Date: Jun 2007 Location: Harker Heights, TX Posts: 1,599	Re: Computer mount pictures Here is what I have so far, I'm still trying to figure out where I'm going to mount it under the dash. __________________ USMC Retired Never trust a man who can't laugh at his own fart! 2010 Silverado Crew Cab 73 SWB 5.3/4l80e Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=695168

01-18-2016, 03:30 AM	#11
Curtb1971 Senior Member Join Date: Feb 2014 Location: Erie Colorado Posts: 1,007	Re: Computer mount pictures Not sure if your application will work but hey might be useful to someone. Had to build a bracket for the DBW pedal so knocked out two birds with one bracket. Kept the throttle cable hole for the mechanical gauge oil line to pass through but filled the washer lines and rear harness holes. Made the plate out of 1/8" steel with a brake in it on the drivers side. Used the original gas pedal bolts and a small 90 degree brace screwed to the cab reinforcement bump out for support. Trans controller. Took 1/4" 20 1 1/4" all thread and welded 1 1/4" fender washers to the end then ground flat to make a stud. I took these and used 3m panel bonding adhesive to glue them directly to the firewall after grinding the paint to bare metal. Did this to eliminate putting screws/hole through the firewall Also glued some studs for the relays on the back side of the cowl gutter.

01-18-2016, 10:13 AM	#12
solidaxel Registered User Join Date: Dec 2002 Location: Cactus Patch So. Az Posts: 4,749	Re: Computer mount pictures Good location for the controllers, where did you get the harness? __________________ 53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42

01-18-2016, 02:35 PM	#13
Curtb1971 Senior Member Join Date: Feb 2014 Location: Erie Colorado Posts: 1,007	Re: Computer mount pictures The wiring Harness is from Howell Industries.

01-18-2016, 09:21 PM	#14
GMC-YA68 Senior Member Join Date: Mar 2004 Location: Lee's Summit, MO (KC) Posts: 742	Re: Computer mount pictures I saw where someone here mounted it inside the glove box and it looked pretty clean. Right now mine is on the pass side floor board up high along with my fuses /relays but I want to move it to the glove box once I put carpet in. __________________ -Keegan- '72 Jimmy 4x4 - 5.3/4L65E/NP205 swap http://67-72chevytrucks.com/vboard/s...d.php?t=663780

01-19-2016, 02:51 PM	#15
fast70swb Registered User Join Date: Apr 2014 Location: Bridge Creek , Oklahoma Posts: 69	Re: Computer mount pictures Curtb1971 What gas pedal is that from and what it work with a 2006 lq4 computer

01-19-2016, 03:43 PM	#16
'68 Newtricks Registered User Join Date: Feb 2014 Location: Los Angeles area :( Posts: 499	Re: Computer mount pictures __________________ '68 C10 SWB '85 K30 Blazer



Register or Log In To remove these advertisements.

01-19-2016, 05:11 PM	#18
fast70swb Registered User Join Date: Apr 2014 Location: Bridge Creek , Oklahoma Posts: 69	Re: Computer mount pictures Thank you I will check it out. I'm at the computer mounting and pedal install test fitting part of my build

03-02-2016, 06:07 PM	#21
LS64C10 Registered User Join Date: Sep 2014 Location: Loranger, LA Posts: 11	Re: Computer mount pictures Here's a few of mine. I made a bracket to mount it behind the glove box at an angle so I could reuse the original liner for the glove box. The only thing you can see is the OBDII port. Attached Images

03-02-2016, 10:31 PM	#22
Dustytrix Registered User Join Date: Jan 2012 Location: Petal,Ms. Posts: 428	Re: Computer mount pictures Great job LS64C10.

03-02-2016, 11:47 PM	#23
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,217	Re: Computer mount pictures I used an 2003 zr2 s10 computer mount boltex to fendor wheel Attached Images __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

Register or Log In To remove these advertisements.