Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
05-26-2019, 10:21 PM | #1 |
Registered User
Join Date: Oct 2015
Location: San Tan Valley, Arizona
Posts: 313
|
Coolant level question
First off, thanks to everyone who has answered my many questions in the past. I fired up the new 350 that i just installed in my 68 c10 today. During break in as the motor came up to temp the radiator puked a bunch of water. Temperature was fine bit i checked and from what i could tell everything was fine. Finished the break in and temp held rather steady the whole time. When it cooled down i checked the coolant in the radiator and it was an inch or two low. I filled it back up and took a quick test drive around the block and it puked some more coolant again.
Now to my question. Is this normal on an open system? I have never owned a vehicle without a coolant bottle. I am guessing this is just the system equalizing and if i had a coolant catch bottle it would get sucked back in as the radiator cooled back down. Does that sound correct? Thanks again for all the help and advice. |
05-26-2019, 10:26 PM | #2 |
Senior Member
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,848
|
Re: Coolant level question
In an open system there's usually about an inch between the top of the radiator and the coolant level. There has to be room for expansion.
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson |
05-27-2019, 01:01 AM | #3 |
Registered User
Join Date: Oct 2015
Location: San Tan Valley, Arizona
Posts: 313
|
Re: Coolant level question
That is what i figured. Thanks for confirming!
|
06-02-2019, 09:27 PM | #4 |
Registered User
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,203
|
Re: Coolant level question
You probably had an air pocket that cleared out.
|
06-02-2019, 11:44 PM | #5 |
Registered User
Join Date: Oct 2015
Location: San Tan Valley, Arizona
Posts: 313
|
Re: Coolant level question
I have a quick follow up story. When this happened i was using straight distilled water. I did this just in case i had some kind of leak during the break in period. I figured that if i did have a leak it would be less mess if i was only using water. The plan was to drain some water out and replace it with coolant. What i didn't think about was the fact that the coolant raises the boiling point significantly. After draining out the water and refilling with coolant to get a proper mix, the level has stayed much closer to what i would expect. It also seemed to puke less coolant when fully warmed up. I think the combination of only using water and not ever having owned a car with an open system caused me to get overly worried.
|
06-03-2019, 09:38 PM | #6 |
Registered User
Join Date: Jul 2015
Location: 2nd left past the stump on a dirt road.
Posts: 2,629
|
Re: Coolant level question
You could have the wrong radiator cap on there. If it is a closed system the cap needs to be for that system.
A open system cap of course would allow coolant to escape out! |
06-04-2019, 02:52 PM | #7 |
Registered User
Join Date: Oct 2015
Location: San Tan Valley, Arizona
Posts: 313
|
Re: Coolant level question
I believe all radiator caps will allow coolant to escape when the system reaches the rated pressure correct? The difference is that the cap for a closed system allows coolant to be pulled back in from the overflow bottle. Without an overflow bottle it just lets air in rather than maintaining a vacuum. That is how i understand it anyway. Please correct me if i am wrong.
|
06-04-2019, 02:56 PM | #8 |
Registered User
Join Date: Oct 2015
Location: San Tan Valley, Arizona
Posts: 313
|
Re: Coolant level question
Also, to be clear my radiator only vents coolant once. If i fill it all the way to the top it will let a little coolant out when it heats up (i assume due to expansion) . Then it will not do it the next time. I think i just got overexcited it being the first time i ever swapped a motor.
|
06-14-2019, 12:10 PM | #9 |
Senior Member
Join Date: Dec 2011
Location: Moraga, CA
Posts: 809
|
Re: Coolant level question
On my break in, it seemed to cool fine when the RPMs were up. When I slowed to idle it started puking. I was running without a fan at that time. I was wondering at that time if I'd overfilled it. I was even thinking about installing a puke can.
When I installed the fan it cooled quite a bit better at idle. When I also installed a fan shroud it cooled perfectly. Now it's about an inch or two from the top and no more puking. I might not need a puke can after all.
__________________
(Very) Slow-Going Build Thread: Stock 1970 Short Step with Stock 1970 LT-1 http://67-72chevytrucks.com/vboard/s...d.php?t=567340 |
Bookmarks |
|
|