My New Whip - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Hotcorner · 03-28-2023, 11:55 PM

Two-owner 2002 and garage kept all the way. Looks almost new. Front tires are wearing unevenly, so it might need some front end work.

**special-K** · 03-29-2023, 07:01 AM

Looks clean. Nice find. I may be entering into the Sonoma world soon. I need a li'l go-getter

Hotcorner · 03-29-2023, 09:08 AM

Thanks. I’m replacing my car and an old Nissan hardbody with one vehicle, so this made sense for my DD.

Hotcorner · 04-19-2023, 01:14 PM

New tires and an alignment. Tires were not cheap. Fortunately, the front end was good to go.

**FleetsidePaul** · 04-28-2023, 01:23 PM

Those are nice looking tires. And I'll bet they weren't cheap. Tires are expensive but it's the price of safety.

My Corvette was making a bumping noise when you turned the wheel sharply and I thought the worst, but new tires and alignment cured it.

Sharp Blazer!!!

Hotcorner · 04-28-2023, 02:58 PM

I just replaced the driver door hinge bushings and it was harder than I expected. The detent spring is a SOB to get out even with the tool. Also, the new bushings are fragile and the pins need to be installed carefully rather than just tapped back in without perfect alignment. Pins prelubricated too.

The first time I did it I knocked the pins down with the hammer and busted one of the bushings. Back to O’Reilly I went and you can’t just buy one bushing. Worse yet you have to take both pins back out to replace the broken bushing and jack up the other bushings.

Anyone replace the front crank seal in the 4.3? I noticed that I have some oil leaking at the front of the engine. Going to try to figure it out but the main seal is apparently a common issue on this motor

New stereo is on the way!

Hotcorner · 04-28-2023, 03:04 PM

Quote:

Originally Posted by FleetsidePaul

Those are nice looking tires. And I'll bet they weren't cheap. Tires are expensive but it's the price of safety.

My Corvette was making a bumping noise when you turned the wheel sharply and I thought the worst, but new tires and alignment cured it.

Sharp Blazer!!!

Paul, that’s quite a garage you’ve got!

**FleetsidePaul** · 04-30-2023, 08:45 AM

Quote:

Originally Posted by Hotcorner

Paul, that’s quite a garage you’ve got!

Thank you. I do have quite a few cars. Too many. I have sort of an addiction to them.

I also have too many ex wives and like the cars they try their best to leave me penniless.

Hotcorner · 04-30-2023, 09:53 AM

Quote:

Originally Posted by FleetsidePaul

Thank you. I do have quite a few cars. Too many. I have sort of an addiction to them.

I also have too many ex wives and like the cars they try their best to leave me penniless.

You and me both! 😂

Hotcorner · 07-03-2023, 02:15 PM

Replaced every front suspension component with new. Control arms, ball joints, Pittman arm, idler arm, sway bar bushings and links, tie rod ends, and shocks. I’m still getting a clunking sound over almost any size bump. Any ideas what it might be? About $1200 spent and I am pissed.

03-28-2023, 11:55 PM	#1
Hotcorner Registered User Join Date: Apr 2017 Location: Knoxville, Tennessee Posts: 892	My New Whip Two-owner 2002 and garage kept all the way. Looks almost new. Front tires are wearing unevenly, so it might need some front end work. Attached Images __________________ 1969 GMC K25 2007 Chevy 2500HD Classic Duramax 1999 Tahoe 2DR 4WD Base Model 5.7l

03-29-2023, 07:01 AM	#2
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,852	Re: My New Whip Looks clean. Nice find. I may be entering into the Sonoma world soon. I need a li'l go-getter __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

03-29-2023, 09:08 AM	#3
Hotcorner Registered User Join Date: Apr 2017 Location: Knoxville, Tennessee Posts: 892	Re: My New Whip Thanks. I’m replacing my car and an old Nissan hardbody with one vehicle, so this made sense for my DD. __________________ 1969 GMC K25 2007 Chevy 2500HD Classic Duramax 1999 Tahoe 2DR 4WD Base Model 5.7l

04-19-2023, 01:14 PM	#4
Hotcorner Registered User Join Date: Apr 2017 Location: Knoxville, Tennessee Posts: 892	Re: My New Whip New tires and an alignment. Tires were not cheap. Fortunately, the front end was good to go. Attached Images __________________ 1969 GMC K25 2007 Chevy 2500HD Classic Duramax 1999 Tahoe 2DR 4WD Base Model 5.7l

04-28-2023, 01:23 PM	#5
FleetsidePaul R.I.P. E.S.L.L. Join Date: Aug 2005 Location: Kernville CA./ Lake Isabella CA. Posts: 11,419	Re: My New Whip Those are nice looking tires. And I'll bet they weren't cheap. Tires are expensive but it's the price of safety. My Corvette was making a bumping noise when you turned the wheel sharply and I thought the worst, but new tires and alignment cured it. Sharp Blazer!!! __________________ 1971 Custom C/20 1970 CST 20 1970 C/30 Flatbed 1983 C/30 Dually 2015 Corvette Z51 2021 Corvette Z51 1991 Cadillac Hearse 1982 Cadillac Eldorado Biarritz 2000 Porsche Boxster S 2020 Jeep Gladiator 1973 VW Thing 1973 Plymouth Satellite wagon 1963 Baja Bug 1959 Bug Dune Buggy 1970 Baja Bug 1987 Jaguar XJ 350. R.I.P. El Jay R.I.P Jessie. R.I.P Grumpy. Every day is a gift from God.

04-28-2023, 02:58 PM	#6
Hotcorner Registered User Join Date: Apr 2017 Location: Knoxville, Tennessee Posts: 892	Re: My New Whip I just replaced the driver door hinge bushings and it was harder than I expected. The detent spring is a SOB to get out even with the tool. Also, the new bushings are fragile and the pins need to be installed carefully rather than just tapped back in without perfect alignment. Pins prelubricated too. The first time I did it I knocked the pins down with the hammer and busted one of the bushings. Back to O’Reilly I went and you can’t just buy one bushing. Worse yet you have to take both pins back out to replace the broken bushing and jack up the other bushings. Anyone replace the front crank seal in the 4.3? I noticed that I have some oil leaking at the front of the engine. Going to try to figure it out but the main seal is apparently a common issue on this motor New stereo is on the way! __________________ 1969 GMC K25 2007 Chevy 2500HD Classic Duramax 1999 Tahoe 2DR 4WD Base Model 5.7l

07-03-2023, 02:15 PM	#10
Hotcorner Registered User Join Date: Apr 2017 Location: Knoxville, Tennessee Posts: 892	Re: My New Whip Replaced every front suspension component with new. Control arms, ball joints, Pittman arm, idler arm, sway bar bushings and links, tie rod ends, and shocks. I’m still getting a clunking sound over almost any size bump. Any ideas what it might be? About $1200 spent and I am pissed. __________________ 1969 GMC K25 2007 Chevy 2500HD Classic Duramax 1999 Tahoe 2DR 4WD Base Model 5.7l



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.