72 2wd Blazer: Project "Break Me" - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jkade · 10-10-2007, 02:31 PM

I bought this blazer back in Nov of 2005 after going on many wild goose chases looking for a 67-72 c10 truck. I drove 10 hours one way to look at one truck and it was a piece when I got there to get it. Came home and saw the blazer on ebay and it was only about a 3 hour ride, I told my wife that if this wasn't the one I was giving up. Got there to look at it and out of the other 10 guys that told me their trucks were rust free this one was actually just that. There where a lot of things I didn't like about it but I did like the fact that it was a great starting point and need just a little block sanding to be a pretty much perfect body. So I bought it and brought it home.

The first thing I did was get my buddy over @ Rods and Restos to get me some 20" torq thrust II's and got them put on there and it sit like a 4x4 instead of a 2wd. Next on the list was a set of drop spindles for the front and some 6" springs and 1.5" block for the back. Got those pieces installed a a bolt in c notch and had it looking pretty good but it need some interior.

The P.O. had installed some buckets and a console out of a 454ss truck and they where mint but the burgandy seats and carpet didn't go to well with the red paint. I stripped the interior and waited 6 months for my name to come up at Wilson's Upholstery in Cedartown, Ga. They had it done in about a month and I was very pleased with what they did for me. I had them cover a set of 98 tahoe front buckets with the headrest removed and a back seat from a 88 suburban. They also made custom door panels, rear panels for the bed, tailgate panel, covered the dash, dash pad, sun visors, carpet, custom bed rail covers, and a custom speaker box.

By the time I got it back I was looking to give the 402 a little more power and bought some heads, cam, headers, edelbrock pro flo, roller rockers, and some dress up goodies plus a stall for the th400. During this time I also installed a eaton posi and a set of 3:73's. Got the motor with the new parts and efi back in and all the efi did was give me trouble. All it would do is foul plugs and really piss me off so I decide to sell the motor and the efi and wait for a GENIII motor.

Well it has been sitting since about march and has the suspension robbed and installed under my 67 c10 truck. So here is what it is going to get.
1. Bought a 2003 LQ4 from a 2500hd truck and I am going to run a car intake and the th400.
2. The front suspension will get moved forward to center it in the wheel well and the rear will get moved back to do the same.
3. Section the front crossmember, add R&P, install tubular arms and bags.
4. If Kore3 comes out with the c5 vette brakes I will intall them on the front and hopefully on the back as well.
5. The rear will have to have as much of a step notch as the factory trailing arms will allow. I don't care to lay frame but I want a pretty low ride height.
6. The firewall will be getting a shave and vintage air will be thrown in somewhere.
7. The factory fuel filler has to go so I think I will cut the one off the 91 suburban parts truck I have and graft it in. And block sand the whole body down and paint. If I run the 1/2 top I will also install a fiberglass bed cover but I may run the full top till the funds pick back up from the rest of the above.

So that is about it in a nutshell. I will post up some pics of when I bought it and the steps along the way.

jkade · 10-10-2007, 02:32 PM

This is the ebay pic, I will scan the pics I took when I got it home tonight.
Name: aa_1.jpg
Views: 4776
Size: 32.5 KB

jkade · 10-10-2007, 02:35 PM

This is after the new 20's

Name: Blazer%20002.jpg
Views: 5070
Size: 82.5 KB

Name: Blazer%20008.jpg
Views: 4852
Size: 95.2 KB

jkade · 10-10-2007, 02:38 PM

This is the new interior

Name: rhino%20002.jpg
Views: 4771
Size: 66.6 KB

Name: rhino%20003.jpg
Views: 4819
Size: 68.5 KB

Name: rhino%20004.jpg
Views: 4648
Size: 69.5 KB

Name: rhino%20005.jpg
Views: 4614
Size: 63.9 KB

jkade · 10-10-2007, 02:49 PM

The old motor setup and what it looked like with the pro flo

Name: Blazer%20004.jpg
Views: 4663
Size: 94.4 KB

Name: Blazer%20005.jpg
Views: 4678
Size: 97.8 KB

Name: Motor%20009.jpg
Views: 4614
Size: 96.1 KB

jkade · 10-10-2007, 02:53 PM

This is how she looked last summer before I parked her. About it's last trip was the Nashville Good Guys were I took home the young guns award with it.

Name: kade%20042.jpg
Views: 4386
Size: 73.8 KB

Name: kade%20042.jpg
Views: 4386
Size: 73.8 KB

Name: kade%20041.jpg
Views: 4353
Size: 92.1 KB

Name: kade.jpg
Views: 4307
Size: 92.1 KB

Name: kade%20045.jpg
Views: 4257
Size: 68.1 KB

crabalais · 10-15-2008, 12:46 AM

I like the newer brake set up. What is it off of?

Quote:

Originally Posted by jkade

The old motor setup and what it looked like with the pro flo

Attachment 305715

Attachment 305716

Attachment 305717

ColoradoK5 · 10-10-2007, 03:07 PM

This is going to be a sweet transformation to follow! I think you should go with the half top you will get the best of both worlds truck and Blazer!!

jkade · 10-10-2007, 03:12 PM

More pics from along the way

Name: Blaze no lowered.jpg
Views: 4222
Size: 95.0 KB

Name: Blazer lowered.jpg
Views: 4324
Size: 97.4 KB

Name: Blazer%20013.jpg
Views: 4170
Size: 97.2 KB

Name: Blazer%20014.jpg
Views: 4264
Size: 94.8 KB

jkade · 10-10-2007, 03:20 PM

This is it's current state but I do have 4 wheels and tires back under it now so I can roll it around.

Name: Blazer%20012.jpg
Views: 4176
Size: 72.6 KB

**SactoJim** · 10-10-2007, 03:41 PM

Keep us posted on this one.....gonna be nice given what it looked like before!

jkade · 10-10-2007, 04:01 PM

Quote:

Originally Posted by SactoJim

Keep us posted on this one.....gonna be nice given what it looked like before!

I will but it is going to be a slow process. Maybe I can get the tub pulled in a week or 2 and start on the suspension.

72BlckButy · 10-15-2007, 01:59 PM

Quote:

Originally Posted by SactoJim

Keep us posted on this one.....gonna be nice given what it looked like before!

that thing will look sweet in the end. Definitely signing up for the show.

67Fleet · 10-15-2007, 06:15 PM

Very nice work so far! Can't wait to see more progress. Best of luck and sorry to hear about your new carpet being used as a nest. That sucks.

ColoradoK5 · 10-10-2007, 05:09 PM

Did your Blazer start out as a 4x4?

jkade · 10-10-2007, 05:22 PM

Quote:

Originally Posted by ColoradoK5

Did your Blazer start out as a 4x4?

Nope, it is a factory 2wd

Frizzle Fry · 10-10-2007, 05:53 PM

Was it a factory big block?

jkade · 10-10-2007, 07:18 PM

Quote:

Originally Posted by Frizzle Fry

Was it a factory big block?

No the PO put that in there, a blazer never came with a bbc but you would have thought this one did.

Frizzle Fry · 10-11-2007, 11:15 AM

Quote:

Originally Posted by jkade

No the PO put that in there, a blazer never came with a bbc but you would have thought this one did.

I didn't think they ever did, but wasn't sure. Why the heck didn't they??? They put them in 2wd trucks and Burbs, why not the blazer

Oh well, your genIII will be better than any stock 402 would have been

jkade · 10-11-2007, 01:41 PM

Quote:

Originally Posted by Frizzle Fry

I didn't think they ever did, but wasn't sure. Why the heck didn't they??? They put them in 2wd trucks and Burbs, why not the blazer

Oh well, your genIII will be better than any stock 402 would have been

Your guess is as good as mine why they didn't come with a bbc but all the dealings I have had with a 402 is they suck. A 350 would blow one off the road as far as performance but the 402 was a torque motor. And yes the lq4 will out perform a 402 any day of the week.

crzngmychvy · 10-11-2007, 01:58 PM

Cool thread! You should post up a webpage to your truck. If you build it up as you build your truck it works out real nice and you end up with good documentation about what you did to it.

1sik7t2 · 02-03-2009, 07:30 PM

hey, i'm putting in a LQ4 IN MY BURB AS WE SPEAK need tons of help though if you have any, i would appreciate it mostly the wire harness, brain, etc if i can help(doubt it but...) i'll try good luck on yours

Quote:

Originally Posted by jkade

Your guess is as good as mine why they didn't come with a bbc but all the dealings I have had with a 402 is they suck. A 350 would blow one off the road as far as performance but the 402 was a torque motor. And yes the lq4 will out perform a 402 any day of the week.

gringoloco · 10-11-2007, 03:25 PM

Subscribing.

LOW DOUGH · 10-11-2007, 04:34 PM

Very nice! I will have to stay tuned

jkade · 10-13-2007, 05:43 PM

Trust me it will be a slow process the way my funds are going. Is anyone else around here in the trucking business? Fuel prices are so high right now it doesn't leave me with much profit after paying, fuel, ins, driver, etc.

10-10-2007, 02:31 PM	#1
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	72 2wd Blazer: Project "Break Me" I bought this blazer back in Nov of 2005 after going on many wild goose chases looking for a 67-72 c10 truck. I drove 10 hours one way to look at one truck and it was a piece when I got there to get it. Came home and saw the blazer on ebay and it was only about a 3 hour ride, I told my wife that if this wasn't the one I was giving up. Got there to look at it and out of the other 10 guys that told me their trucks were rust free this one was actually just that. There where a lot of things I didn't like about it but I did like the fact that it was a great starting point and need just a little block sanding to be a pretty much perfect body. So I bought it and brought it home. The first thing I did was get my buddy over @ Rods and Restos to get me some 20" torq thrust II's and got them put on there and it sit like a 4x4 instead of a 2wd. Next on the list was a set of drop spindles for the front and some 6" springs and 1.5" block for the back. Got those pieces installed a a bolt in c notch and had it looking pretty good but it need some interior. The P.O. had installed some buckets and a console out of a 454ss truck and they where mint but the burgandy seats and carpet didn't go to well with the red paint. I stripped the interior and waited 6 months for my name to come up at Wilson's Upholstery in Cedartown, Ga. They had it done in about a month and I was very pleased with what they did for me. I had them cover a set of 98 tahoe front buckets with the headrest removed and a back seat from a 88 suburban. They also made custom door panels, rear panels for the bed, tailgate panel, covered the dash, dash pad, sun visors, carpet, custom bed rail covers, and a custom speaker box. By the time I got it back I was looking to give the 402 a little more power and bought some heads, cam, headers, edelbrock pro flo, roller rockers, and some dress up goodies plus a stall for the th400. During this time I also installed a eaton posi and a set of 3:73's. Got the motor with the new parts and efi back in and all the efi did was give me trouble. All it would do is foul plugs and really piss me off so I decide to sell the motor and the efi and wait for a GENIII motor. Well it has been sitting since about march and has the suspension robbed and installed under my 67 c10 truck. So here is what it is going to get. 1. Bought a 2003 LQ4 from a 2500hd truck and I am going to run a car intake and the th400. 2. The front suspension will get moved forward to center it in the wheel well and the rear will get moved back to do the same. 3. Section the front crossmember, add R&P, install tubular arms and bags. 4. If Kore3 comes out with the c5 vette brakes I will intall them on the front and hopefully on the back as well. 5. The rear will have to have as much of a step notch as the factory trailing arms will allow. I don't care to lay frame but I want a pretty low ride height. 6. The firewall will be getting a shave and vintage air will be thrown in somewhere. 7. The factory fuel filler has to go so I think I will cut the one off the 91 suburban parts truck I have and graft it in. And block sand the whole body down and paint. If I run the 1/2 top I will also install a fiberglass bed cover but I may run the full top till the funds pick back up from the rest of the above. So that is about it in a nutshell. I will post up some pics of when I bought it and the steps along the way. Last edited by jkade; 10-10-2007 at 02:35 PM.

10-10-2007, 02:32 PM	#2
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" This is the ebay pic, I will scan the pics I took when I got it home tonight. Last edited by jkade; 10-10-2007 at 07:43 PM.

10-10-2007, 02:35 PM	#3
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" This is after the new 20's

10-10-2007, 02:38 PM	#4
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" This is the new interior Last edited by jkade; 10-10-2007 at 02:47 PM.

10-10-2007, 02:49 PM	#5
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" The old motor setup and what it looked like with the pro flo

10-10-2007, 02:53 PM	#6
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" This is how she looked last summer before I parked her. About it's last trip was the Nashville Good Guys were I took home the young guns award with it.

10-10-2007, 03:07 PM	#8
ColoradoK5 Registered User Join Date: Jan 2007 Location: Denver Colorado Posts: 608	Re: 72 2wd Blazer: Project "Break Me" This is going to be a sweet transformation to follow! I think you should go with the half top you will get the best of both worlds truck and Blazer!!

10-10-2007, 03:12 PM	#9
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" More pics from along the way

10-10-2007, 03:20 PM	#10
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" This is it's current state but I do have 4 wheels and tires back under it now so I can roll it around.

10-10-2007, 03:41 PM	#11
SactoJim Registered User Join Date: Oct 2005 Location: Sacramento, CA Posts: 1,970	Re: 72 2wd Blazer: Project "Break Me" Keep us posted on this one.....gonna be nice given what it looked like before! __________________ 72 Cheyenne SWB Fleet Nut & bolt frame off in progress...99.9999% - supercharged 383 - 4 wheel discs - relocated fuel tank - My Build Thread

10-15-2007, 06:15 PM	#14
67Fleet Outlandish Trends - FL Join Date: Jul 2005 Location: Orlando Posts: 1,396	Re: 72 2wd Blazer: Project "Break Me" Very nice work so far! Can't wait to see more progress. Best of luck and sorry to hear about your new carpet being used as a nest. That sucks. __________________ -Bret 67 short-fleet sold!

10-10-2007, 05:09 PM	#15
ColoradoK5 Registered User Join Date: Jan 2007 Location: Denver Colorado Posts: 608	Re: 72 2wd Blazer: Project "Break Me" Did your Blazer start out as a 4x4?

10-10-2007, 05:53 PM	#17
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: 72 2wd Blazer: Project "Break Me" Was it a factory big block?

10-11-2007, 01:58 PM	#21
crzngmychvy "1972 C5" Join Date: Jul 2004 Location: SoCal Posts: 729	Re: 72 2wd Blazer: Project "Break Me" Cool thread! You should post up a webpage to your truck. If you build it up as you build your truck it works out real nice and you end up with good documentation about what you did to it. __________________ - 72 2wd Blazer ...sold... 2wd Blazer Page

10-11-2007, 03:25 PM	#23
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,920	Re: 72 2wd Blazer: Project "Break Me" Subscribing. __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy



Register or Log In To remove these advertisements.

10-11-2007, 04:34 PM	#24
LOW DOUGH I'M TRUCK CRAZY! Join Date: Oct 2006 Location: Sachse, TEXAS Posts: 1,737	Re: 72 2wd Blazer: Project "Break Me" Very nice! I will have to stay tuned

10-13-2007, 05:43 PM	#25
jkade Senior Member Join Date: Nov 2005 Location: AL Posts: 2,519	Re: 72 2wd Blazer: Project "Break Me" Trust me it will be a slow process the way my funds are going. Is anyone else around here in the trucking business? Fuel prices are so high right now it doesn't leave me with much profit after paying, fuel, ins, driver, etc.

Register or Log In To remove these advertisements.