The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-14-2014, 10:38 AM   #51
dec010974
Senior Member
 
dec010974's Avatar
 
Join Date: Oct 2012
Location: Miami, Florida
Posts: 930
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

muckyp, I had clearance issues with the lower control rubbing/interfering the inner rally wheels and wheel balance weights. I also had to clearance/grind the tie rod area of the drop spindle. For my application, a grinder was my best tool until I decide to buy larger wheels. Im running my stock rally wheels which are 15x8. I used the belltech 3 inch drop spindle, stock lower control arms, & the air bag in the lower control spring pocket. I also used a PB stage 1 lowering kit which relocated the shock mounts. i hope this helps.
dec010974 is offline   Reply With Quote
Old 03-14-2014, 11:57 AM   #52
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by muckyp View Post
MattPSU - are those 15" wheels on the truck in the photos? If so did you have issues with the wheels rubbing the lower control arms?
Yes, they are 15x7's and they rubbed on the lower control arm which did a great job of shaving my wheel weights. I don't have a picture of the arms, but I do have some pictures of the wheel weights. I can try to take some pictures of the arms this weekend.

Enjoy! - Matt
Attached Images
  
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 03-14-2014, 10:25 PM   #53
muckyp
Registered User
 
muckyp's Avatar
 
Join Date: Mar 2001
Location: Forney, Texas
Posts: 290
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MattPSU View Post
Yes, they are 15x7's and they rubbed on the lower control arm which did a great job of shaving my wheel weights. I don't have a picture of the arms, but I do have some pictures of the wheel weights. I can try to take some pictures of the arms this weekend.

Enjoy! - Matt
I have the same drop spindles and bags in front. Did you grind the lower control arms? I plan a larger wheel but those things are $$$$$, so I need some time prep the wife for the purchase.
__________________
70 SWB 454/TH400
muckyp is offline   Reply With Quote
Old 03-15-2014, 05:10 PM   #54
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by muckyp View Post
I have the same drop spindles and bags in front. Did you grind the lower control arms? I plan a larger wheel but those things are $$$$$, so I need some time prep the wife for the purchase.
I trimmed them with a sawzall & cut-off wheel, then cleaned it up with my grinder.
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 03-28-2014, 08:26 PM   #55
MRWGN
Registered User
 
Join Date: Mar 2014
Location: Sydney Australia
Posts: 2
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Just wondering how much lower (if any) having tubular control arms would make it?

I ask because the way the bag mounting happens with the stage 1 kit it brings the mounting surface flush with arm and not recessed into the cup.

Would a set of porterbuilt tubular arms/CPP arms in standard form change those dimensions and make it lower again in the front?
MRWGN is offline   Reply With Quote
Old 03-30-2014, 11:59 AM   #56
King Cary
Registered User
 
Join Date: Feb 2014
Location: Phoenix, AZ
Posts: 60
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Thanks for the chart Matt... Awesome lay out for everyone to use as a comparison when building their trucks... I see you're in Lyman S.C., I'm originally from Columbia.
King Cary is offline   Reply With Quote
Old 03-30-2014, 07:48 PM   #57
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MRWGN View Post
Just wondering how much lower (if any) having tubular control arms would make it?

I ask because the way the bag mounting happens with the stage 1 kit it brings the mounting surface flush with arm and not recessed into the cup.

Would a set of porterbuilt tubular arms/CPP arms in standard form change those dimensions and make it lower again in the front?
No idea. Maybe Travis or one of the Porterbuilt guys will chime in and let us know. If they send me a set, I'll install them and take some pictures, too!

Quote:
Originally Posted by King Cary View Post
Thanks for the chart Matt... Awesome lay out for everyone to use as a comparison when building their trucks... I see you're in Lyman S.C., I'm originally from Columbia.
You're welcome. Small world!
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 03-30-2014, 09:18 PM   #58
hass18
Registered User
 
Join Date: Jan 2014
Location: Grand Island, NE
Posts: 10
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Does anyone have any pictures of how and where all the air valves and controller is mounted? Just looking for ideas on how to plumb and set up.
hass18 is offline   Reply With Quote
Old 03-31-2014, 09:09 AM   #59
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by hass18 View Post
Does anyone have any pictures of how and where all the air valves and controller is mounted? Just looking for ideas on how to plumb and set up.
Here are some pictures of my air management set up which is Pro Performance's Pro 2 kit. I mounted my valve block, relays, & power distribution block on the cross member that's just behind the axle. The tank is mounted on a 2x2 that spans the rear of the frame where the original rear cross member used to be.
Attached Images
     
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 03-31-2014, 09:13 AM   #60
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

I don't have any pictures of the AVS controller but here's one of my gauges inside the cab.
Attached Images
 
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 03-31-2014, 09:53 AM   #61
Pro Performance
Registered User
 
Pro Performance's Avatar
 
Join Date: Aug 2010
Location: AZ
Posts: 3,069
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MRWGN View Post
Just wondering how much lower (if any) having tubular control arms would make it?

I ask because the way the bag mounting happens with the stage 1 kit it brings the mounting surface flush with arm and not recessed into the cup.

Would a set of porterbuilt tubular arms/CPP arms in standard form change those dimensions and make it lower again in the front?
The PB arms will lower the truck more, by placing that bag mount lower in the a-arm as you described. I don't know the exact measurement, but you will see appx. 3/4" more of drop.

- Travis
Pro Performance is offline   Reply With Quote
Old 03-31-2014, 10:07 AM   #62
hass18
Registered User
 
Join Date: Jan 2014
Location: Grand Island, NE
Posts: 10
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MattPSU View Post
Here are some pictures of my air management set up which is Pro Performance's Pro 2 kit. I mounted my valve block, relays, & power distribution block on the cross member that's just behind the axle. The tank is mounted on a 2x2 that spans the rear of the frame where the original rear cross member used to be.
Thanks for the pics. That was where I thought would be the best place to mount.
hass18 is offline   Reply With Quote
Old 04-02-2014, 01:08 AM   #63
Carbajal
Registered User
 
Carbajal's Avatar
 
Join Date: Mar 2009
Location: Lake Elsinore, California
Posts: 90
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Truck looks good. I like the way it looks That's the setup I'm going to put on my c10. What size tires do you have??
Carbajal is offline   Reply With Quote
Old 04-03-2014, 01:21 PM   #64
clemsonteg
Registered User
 
Join Date: Jul 2012
Location: Anderson,SC
Posts: 953
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Thanks for the chart. I asked about this about a year ago and this is exactly the information I was looking for. I see in the first few photos you are at 80 psi front and 40 psi rear, but in the last few you list ride height at 60 psi front and 25 psi rear. Is that where you have always kept the ride height, or have you reduced it over time to fine tune the firmness you were after?
clemsonteg is offline   Reply With Quote
Old 04-03-2014, 09:11 PM   #65
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by hass18 View Post
Thanks for the pics. That was where I thought would be the best place to mount.
Your welcome!

Quote:
Originally Posted by Carbajal View Post
Truck looks good. I like the way it looks That's the setup I'm going to put on my c10. What size tires do you have??
Current tires are 275/60R15 on 7" rally wheels. About 27.5" tall. Someday I hope to upgrade to 20's.

Quote:
Originally Posted by clemsonteg View Post
Thanks for the chart. I asked about this about a year ago and this is exactly the information I was looking for. I see in the first few photos you are at 80 psi front and 40 psi rear, but in the last few you list ride height at 60 psi front and 25 psi rear. Is that where you have always kept the ride height, or have you reduced it over time to fine tune the firmness you were after?
At 80psi front and 40 psi rear, the bags are about fully inflated and that's as high as the truck can go. Initially I was thinking about showing the possible difference from fully deflated to fully inflated. I wasn't thinking about ride height which is somewhere in between. The more I drive it, the more I've been able to dial in the ride height which is more like 60psi front and 25 psi rear.

Clemsonteg - Be sure to check out the link to the Upstate GM Trucks Club that's in my signature. We've been getting together about once a month and we had 35 trucks show up in March.
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 04-03-2014, 10:33 PM   #66
clemsonteg
Registered User
 
Join Date: Jul 2012
Location: Anderson,SC
Posts: 953
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Matt- thanks for the heads up. I've seen the pics in the regional forum. I definitely want to make it out, I just recently got the front end back on the my truck and got it back on the road. Once I get the kinks worked out I'll feel better about driving it to greenville.
clemsonteg is offline   Reply With Quote
Old 04-16-2014, 02:47 PM   #67
Desert.Chevy
Registered User
 
Desert.Chevy's Avatar
 
Join Date: Nov 2012
Location: Earth
Posts: 338
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MattPSU View Post
Your welcome!



Current tires are 275/60R15 on 7" rally wheels. About 27.5" tall. Someday I hope to upgrade to 20's.



At 80psi front and 40 psi rear, the bags are about fully inflated and that's as high as the truck can go.
Initially I was thinking about showing the possible difference from fully deflated to fully inflated.

I wasn't thinking about ride height which is somewhere in between. The more I drive it, the more I've been able to dial in the ride height which is more like 60psi front and 25 psi rear.

Clemsonteg - Be sure to check out the link to the Upstate GM Trucks Club that's in my signature. We've been getting together about once a month and we had 35 trucks show up in March.
I would like to see some pictures of the three heights, and the psi they have.
Desert.Chevy is offline   Reply With Quote
Old 04-16-2014, 03:50 PM   #68
MattPSU
Registered User
 
MattPSU's Avatar
 
Join Date: Nov 2011
Location: Lyman, SC
Posts: 734
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by Desert.Chevy View Post
I would like to see some pictures of the three heights, and the psi they have.
The 4th, 6th & 7th pairs of pictures show you the heights as they are now in various pressures.

The 4th pair of pictures is aired all the way up, the 6th pair is at ride height, and the 7th is aired up.

Hope that helps. - Matt
__________________
Matt Criswell - Lyman, SC

1972 Chevy Cheyenne SWB - Build: Porterbuilt State 1 Front & Rear, Bolt in Notch, McGaughys 2.5 Drop Spindles, Boyd Welding Fuel Tank

UPSTATE SC GM TRUCK CLUB: FACEBOOK WEBSITE
MattPSU is offline   Reply With Quote
Old 04-17-2014, 01:03 PM   #69
Desert.Chevy
Registered User
 
Desert.Chevy's Avatar
 
Join Date: Nov 2012
Location: Earth
Posts: 338
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by MattPSU View Post
The 4th, 6th & 7th pairs of pictures show you the heights as they are now in various pressures.

The 4th pair of pictures is aired all the way up, the 6th pair is at ride height, and the 7th is aired up.

Hope that helps. - Matt
Awesome Thanks.
Desert.Chevy is offline   Reply With Quote
Old 08-28-2015, 10:15 AM   #70
jus2qwk
Registered User
 
jus2qwk's Avatar
 
Join Date: Mar 2011
Location: Wytheville, Virginia
Posts: 591
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

I bought the stage 1 front and added the control arms later and have the stage 2 basic and used CCP trailing arms with blocks... I bought all mine at different times if I could do it again I would have bought it all at once and went with the deluxe kits. but here is the end result. also made some bumpstops for the front because the tire hits the fender. the bump stomps get the tire just off the fender by about 1/4 inch


this is before the bump stops setting on the fenders


Bump stops


here it is all aired out. I changed the rear bump stops so it sets about an inch lower in the rear
__________________
Corey Jones Designs
CoreyJonesDesigns on instagram
Ole Silver- 1967 stepside
http://www.hotrod.com/articles/1103c...chevrolet-c10/
http://67-72chevytrucks.com/vboard/s...d.php?t=598758
jus2qwk is offline   Reply With Quote
Old 08-28-2015, 10:17 AM   #71
jus2qwk
Registered User
 
jus2qwk's Avatar
 
Join Date: Mar 2011
Location: Wytheville, Virginia
Posts: 591
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

whoops put this on the wrong thread... kinda
__________________
Corey Jones Designs
CoreyJonesDesigns on instagram
Ole Silver- 1967 stepside
http://www.hotrod.com/articles/1103c...chevrolet-c10/
http://67-72chevytrucks.com/vboard/s...d.php?t=598758
jus2qwk is offline   Reply With Quote
Old 08-28-2015, 10:53 AM   #72
darkhorse970
Registered User
 
darkhorse970's Avatar
 
Join Date: May 2009
Location: Monroe, LA
Posts: 2,105
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Quote:
Originally Posted by jus2qwk View Post
I bought the stage 1 front and added the control arms later and have the stage 2 basic and used CCP trailing arms with blocks... I bought all mine at different times if I could do it again I would have bought it all at once and went with the deluxe kits. but here is the end result. also made some bumpstops for the front because the tire hits the fender. the bump stomps get the tire just off the fender by about 1/4 inch


here it is all aired out. I changed the rear bump stops so it sets about an inch lower in the rear
Love the stance! What are the rear tires size and wheel specs?
__________________
Keith

SOLD - 1963 C10 Short Fleet
350/700R4
4/6 drop

1967 GMC Super Custom - Short Fleet
COPO concept w/427 BBC
T-400 w/Doug Nash overdrive
4/6 Drop, Buddy Buckets, etc...
Frame Off (In Progress)
I call it "Vulgar Display of Power"

1980 Silverado
Original paint
49k Original miles
4/6 drop


Check out my build thread here: http://67-72chevytrucks.com/vboard/s...=1#post6209941
darkhorse970 is offline   Reply With Quote
Old 04-03-2016, 06:17 AM   #73
crazycrew
Registered User
 
Join Date: Apr 2016
Location: Vacherie, LA
Posts: 30
Re: Porterbuilt Stage 1 Front and Rear Kit Chart

Awesome thread Matt. I don't have a C10 yet, but i'm actively searching and suspension is gonna be one of the first mods. Thanks
crazycrew is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:48 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com