MD the panelburb getting cut up

[Madkidd007]

Originally Posted by richard2717

How far back into the 3rd door upper rail would you need so I can get a rough idea of crate size? Need all the way to the front angle down at the A pillar?

I would figure it would be at least 150 shipping but would want to check it b4 hand anyway.

On the top it would be 1” from the weatherstripping lip on both sides.
The upper door jamb 1” from the front corner, which lines up perfect with where the flat piece overlaps.
The bottom 7” wide which puts both sides just to the outside edge of the two curves

And to be honest I could care less about crating and fastenal. I’d be fine with wrapped in cardboard and sent. For what I need it for a little edge damage isn’t going to make a difference and it’s on 4.5” long. I’d say tape the upper door jamb to the b-pillar. Do a crude cardboard wrap and send it.

[richard2717]

Originally Posted by Madkidd007

On the top it would be 1” from the weatherstripping lip on both sides.
The upper door jamb 1” from the front corner, which lines up perfect with where the flat piece overlaps.
The bottom 7” wide which puts both sides just to the outside edge of the two curves

And to be honest I could care less about crating and fastenal. I’d be fine with wrapped in cardboard and sent. For what I need it for a little edge damage isn’t going to make a difference and it’s on 4.5” long. I’d say tape the upper door jamb to the b-pillar. Do a crude cardboard wrap and send it.

So basically like what I show in this picture. I have put a gray box covering what gets cut off (this is old pic and part is gone just using for clearer reference)

This "might be able to be sent UPS ground at considerable savings over freight. Let me get full measurements this afternoon and I will cost it.


.

[Madkidd007]

Originally Posted by richard2717

So basically like what I show in this picture. I have put a gray box covering what gets cut off (this is old pic and part is gone just using for clearer reference)

This "might be able to be sent UPS ground at considerable savings over freight. Let me get full measurements this afternoon and I will cost it.


.

Yes that would work perfect. And you can cut the top right piece off 1” from the weatherstripping lip since I’m gonna cut it anyways. Then tape it to the b-pillar so it’s a straight piece to ship

[richard2717]

Originally Posted by Madkidd007

Yes that would work perfect. And you can cut the top right piece off 1” from the weatherstripping lip since I’m gonna cut it anyways. Then tape it to the b-pillar so it’s a straight piece to ship

pm your full address so I can get an accurate shipping quote
Thanks

[Madkidd007]

Originally Posted by richard2717

So basically like what I show in this picture. I have put a gray box covering what gets cut off (this is old pic and part is gone just using for clearer reference)

This "might be able to be sent UPS ground at considerable savings over freight. Let me get full measurements this afternoon and I will cost it.


.

Alright I’ll take the B-Pillar officially now. Before I send payment, do you have the 3rd door rocker trim/sill plate? If so how much so I can add it in.

[richard2717]

Originally Posted by Madkidd007

Alright I’ll take the B-Pillar officially now. Before I send payment, do you have the 3rd door rocker trim/sill plate? If so how much so I can add it in.

I have a couple of them in nice shape $25 each should not affect shipping costs at all if included with pillar

[richard2717]

Originally Posted by Madkidd007

Alright I’ll take the B-Pillar officially now. Before I send payment, do you have the 3rd door rocker trim/sill plate? If so how much so I can add it in.

I am guessing I already sold my real nice one. Here are the 2 that I can find. Both have issues as shown in pictures

.

[Madkidd007]

Originally Posted by richard2717

I am guessing I already sold my real nice one. Here are the 2 that I can find. Both have issues as shown in pictures

.

Was about to jump on 1 and then I seen the hole. Guess I’ll be passing on that and just go for the pillar, door jamb, and cooler