Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
01-16-2021, 09:03 PM | #1 |
A guy with a truck
Join Date: Sep 2005
Location: Germany, for now
Posts: 5,920
|
Re: How to: Ruin a perfectly good C10
I know, right!? Nice trick for us solo workers without a huge bench vise.
Thanks Troy, it’s a blessing and a curse. TCP Global used to advertise the percentage gloss, but I can’t find it now. I’d guess somewhere around 10-15%
__________________
-Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy |
01-16-2021, 09:15 PM | #2 |
A guy with a truck
Join Date: Sep 2005
Location: Germany, for now
Posts: 5,920
|
Re: How to: Ruin a perfectly good C10
...and after at minimum 37 times in and out of the housing, the new posi carrier is torqued down. Pretty happy with how the gears setup, though I’d maybe like the pinion just a tiny touch deeper, when I tried that it didn’t like it and threw the pattern way off. Pulled .005 out of the pinion shim and ended up with a nice, smooth, even pattern on the coast side, slightly towards center on the drive side, and with a relatively tight .008 backlash. Done. Now to put it all back together and lay some twin stripes
__________________
-Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy |
01-17-2021, 01:45 AM | #3 |
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,992
|
Re: How to: Ruin a perfectly good C10
Nice, clean pattern there.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
01-17-2021, 10:37 PM | #4 |
A guy with a truck
Join Date: Sep 2005
Location: Germany, for now
Posts: 5,920
|
Re: How to: Ruin a perfectly good C10
Thanks Scoti, definitely found its happy place.
She’s all buttoned up now, waiting for cover sealant to cure, then dump fluids. Also went ahead and had the driveshaft balanced while it was out and did the 500 mile break-in flush on the TKO and refilled with synchromesh. Hoping it’s smooth and quiet when I get her back on the road...
__________________
-Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy |
Bookmarks |
|
|