|
10-31-2022, 12:40 PM | #1 |
Registered User
Join Date: Nov 2014
Location: somewhere, PA
Posts: 1,040
|
Re: My 52 GMC Build
|
11-04-2022, 10:03 AM | #2 |
Registered User
Join Date: Oct 2014
Location: Kitchener, Ontario, Canada
Posts: 3,254
|
Re: My 52 GMC Build
Ya I thought so. ALH, 20psi, .216 nozzles, 2 1/4" mandrel bent exhaust.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=648459 https://67-72chevytrucks.com/vboard/...d.php?t=769441 1951 MG TD 1967 Jeep CJ5 1.9L TDI 33X13.5X15 Mud Grapplers. 1952 GMC 9700 p/u 7.3L diesel on air, dually |
11-18-2022, 03:58 PM | #3 |
Registered User
Join Date: Oct 2014
Location: Kitchener, Ontario, Canada
Posts: 3,254
|
Re: My 52 GMC Build
Well after taking some time to work on our new cargo trailer camper while the weather was nice, I'm back on the motor swap. I got the upgraded injectors and push rods all in and new exhaust up pipes in and wrapped. Regulated fuel return system all in, the motor is together. Then I started pulling the truck apart, I'm sad and excited all at the same time.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=648459 https://67-72chevytrucks.com/vboard/...d.php?t=769441 1951 MG TD 1967 Jeep CJ5 1.9L TDI 33X13.5X15 Mud Grapplers. 1952 GMC 9700 p/u 7.3L diesel on air, dually |
11-21-2022, 10:38 AM | #4 | |
GMC's n H.D.'s too!
Join Date: Oct 2010
Location: Nampa, Idaho
Posts: 1,583
|
Re: My 52 GMC Build
Hopefully the inspector in that last picture approves all this work!
Quote:
|
|
11-22-2022, 10:27 AM | #5 |
Registered User
Join Date: Oct 2014
Location: Kitchener, Ontario, Canada
Posts: 3,254
|
Re: My 52 GMC Build
Sometimes I need to bribe him lol
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=648459 https://67-72chevytrucks.com/vboard/...d.php?t=769441 1951 MG TD 1967 Jeep CJ5 1.9L TDI 33X13.5X15 Mud Grapplers. 1952 GMC 9700 p/u 7.3L diesel on air, dually |
11-22-2022, 10:37 AM | #6 |
Registered User
Join Date: Oct 2014
Location: Kitchener, Ontario, Canada
Posts: 3,254
|
Re: My 52 GMC Build
Well 7.3L idi diesel and transmission are out and 7.3L powerstroke is set in-ish. I will need to cut some of the fire wall at the top as well on the drivers side a bit. The motor is sitting on the motor mounts but needs to go back 1". Now to pull under the dash apart and remove all the wire to do with the old motor, then I can cut.
__________________
http://67-72chevytrucks.com/vboard/s...d.php?t=648459 https://67-72chevytrucks.com/vboard/...d.php?t=769441 1951 MG TD 1967 Jeep CJ5 1.9L TDI 33X13.5X15 Mud Grapplers. 1952 GMC 9700 p/u 7.3L diesel on air, dually |
11-22-2022, 10:47 AM | #7 |
Registered User
Join Date: Sep 2018
Location: Ontario
Posts: 791
|
Re: My 52 GMC Build
well, you can't turn back now.
looking good, Hope all is well
__________________
https://67-72chevytrucks.com/vboard/...=797726&page=3http://https://67-72chevytrucks.com/...=797726&page=3 51 Chev 5 window on S10 with SBC 1958 Pontiac Wagon build https://67-72chevytrucks.com/vboard/...d.php?t=849781 |
11-23-2022, 11:06 AM | #8 | |
Registered User
Join Date: Jun 2012
Location: Selkirk Ontario Canada
Posts: 1,141
|
Re: My 52 GMC Build
Quote:
__________________
My 63 GMC Panel Slow Build http://67-72chevytrucks.com/vboard/s...=1#post5457281 63 |
|
Bookmarks |
Tags |
bagged, build, diesel, gmc, hot rod |
|
|