What did you do to your truck today? Chapter II - Page 173 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

BugzC10 · 09-08-2016, 05:39 PM

Installed new battery and red hot wire from starter to relay

webfoot · 09-08-2016, 07:26 PM

Today I continued to wait for my new turn signal switch to get here.

**RodnRudy** · 09-08-2016, 07:41 PM

Quick answer for Dads72, Truck has 5 1/2", 7" drop on 15" rallys

74baggedbug · 09-08-2016, 11:01 PM

Quote:

Originally Posted by firedemon

I like the looks of that better than the one lmc sells . the one lmc sells works in that it keeps everything out , but I think the holes are too small seems like the vents don't throw enough air now

What construction adhesive did you use? Thanks

San Diego Ron · 09-10-2016, 08:06 PM

Well, today I taped and sprayed epoxy primer/sealer.

68 Stepper · 09-10-2016, 10:45 PM

[That is a good buddy!

Great loking emblems.

QUOTE=74baggedbug;7704909]

Buddy made these for me to take the place of the factory c/10 on the fenders[/QUOTE]

In The Ten Ring · 09-11-2016, 12:06 AM

Quote:

Originally Posted by 68 Stepper

[That is a good buddy!

Great loking emblems.

QUOTE=74baggedbug;7704909]

Buddy made these for me to take the place of the factory c/10 on the fenders

[/QUOTE]

God blessed Texas!

cruisinthe34 · 09-11-2016, 04:24 AM

Started on the 6" static rear drop.

cruisinthe34 · 09-11-2016, 04:24 AM

Started on the 6" static rear drop.

Possmguts · 09-11-2016, 02:16 PM

Went for a little imaginary cruise today... She ran like a champ and I smoked a couple mustangs and a few ricers...

88fordf150 · 09-11-2016, 05:50 PM

Quote:

Originally Posted by Possmguts

Went for a little imaginary cruise today... She ran like a champ and I smoked a couple mustangs and a few ricers...

Yep! I do the same thing. lol

1968aj · 09-11-2016, 09:34 PM

Did some cleaning on the trucks. took them for a short ride one at a time of course. its a long story how I ended up with 3 69 models and really wanted a 68.

everettelane · 09-11-2016, 10:02 PM

Built a new trans cross member for my six speed made it so i could run exhaust under it also cut out the rear cross member and welded in plate to run exhaust through it.Pay no attention to the (temporary) fuel lines i had to do that to move the truck, i plan on going stainless tubing.

**RodnRudy** · 09-12-2016, 07:21 PM

Yesterday I reinstalled the tail light trim that came with the truck, not 68 correct but I like it and it's cheap like me. Today I reinstalled the door sill plates and hauled the rider to the daughters and mowed her grass. This old girl hauls!

Dad's72 · 09-12-2016, 07:28 PM

Quote:

Originally Posted by cruisinthe34

Started on the 6" static rear drop.

How did that install go? Do tell. What drop did you buy? ECE?

crazyjeenyus · 09-12-2016, 11:38 PM

Broke in the cam on the new engine with my newly built run-stand.

VWNate1 · 09-13-2016, 12:50 PM

RE : cam breakin ~ what RPM's and how long did you run it ? .

66clow · 09-13-2016, 02:21 PM

I didn't let living in a an apartment keep me from doing a little bodywork

also tested out some temporary rattle can colors. May go with the satin blue on the bottom and plastidip the top satin black or just rattle can all of it.

San Diego Ron · 09-13-2016, 05:55 PM

Nice truck, I wouldn't raddle can it, Maaco quoted me price of $900 with body work or $300 less without door jams. Want to two-tone mine so going it alone with paint from (Paint For Cars. com) Toms River, N.J. ...$75/$85 per gallon kit with everything. By the way mine is going to be silver on top with Midnight Blue on bottom...about like your color.

crazyjeenyus · 09-13-2016, 06:23 PM

Quote:

Originally Posted by VWNate1

RE : cam breakin ~ what RPM's and how long did you run it ? .

I ran it at 2500 for 17min. then i varied between 2000 and 3000 for 5 or so min.

383
flat tops
xe274h
Holley Classic 600cfm

colgad · 09-13-2016, 06:51 PM

Quote:

Originally Posted by everettelane

Built a new trans cross member for my six speed made it so i could run exhaust under it also cut out the rear cross member and welded in plate to run exhaust through it.Pay no attention to the (temporary) fuel lines i had to do that to move the truck, i plan on going stainless tubing.

Can we get a photo of the shifter location in the cab? And what shifter location did you use on the trans? Is this the T56 Magnum 6 speed?

Really nice job on the trans mount by the way!

Thanks!!!

In The Ten Ring · 09-13-2016, 07:15 PM

I wished I had it back together and running. Does that count?

66clow · 09-13-2016, 08:21 PM

Quote:

Originally Posted by San Diego Ron

Nice truck, I wouldn't raddle can it, Maaco quoted me price of $900 with body work or $300 less without door jams. Want to two-tone mine so going it alone with paint from (Paint For Cars. com) Toms River, N.J. ...$75/$85 per gallon kit with everything. By the way mine is going to be silver on top with Midnight Blue on bottom...about like your color.

Thanks for the advise. I just want to be able to take it completely apart when I do paint it. Funds tight right now so just wanted something temporary and cheap.

TwoFiftyShifter · 09-13-2016, 08:24 PM

I put new valve cover gaskets on and some hooks in the stake pockets. Drove around some too with my dog.

firedemon · 09-13-2016, 09:50 PM

Quote:

Originally Posted by 66clow

I didn't let living in a an apartment keep me from doing a little bodywork

also tested out some temporary rattle can colors. May go with the satin blue on the bottom and plastidip the top satin black or just rattle can all of it.

instead of rattle cans have you checked out duplicolor they have a cheap already mixed paint system for a spray gun . it is only a small step better than spray bombs but its easier to get it looking even . it is laquer but should hold up better and look better probably around 200 bucks to do a truck our size . no mixing pour through a strainer right into a gun and spray

09-08-2016, 05:39 PM	#4301
BugzC10 Registered User Join Date: Oct 2012 Location: Green Valley Arizona Posts: 1,351	Re: What did you do to your truck today? Chapter II Installed new battery and red hot wire from starter to relay Attached Images __________________ 1970 C10 Short Stepper with 71/72 front clip.

09-08-2016, 07:26 PM	#4302
webfoot Registered User Join Date: Nov 2007 Location: Hermiston, OR Posts: 947	Re: What did you do to your truck today? Chapter II Today I continued to wait for my new turn signal switch to get here. __________________ *Running in place gets you nowhere fast.* -me 1968 GTO 4-spd covnvertible 1970 K-20 4-speed, factory AC.

09-08-2016, 07:41 PM	#4303
RodnRudy Senior Member Join Date: Oct 2014 Location: New Palestine In Posts: 930	Re: What did you do to your truck today? Chapter II Quick answer for Dads72, Truck has 5 1/2", 7" drop on 15" rallys __________________ Phil "Money is only a tool to create and achieve what you want most in life" PayPal: rodnrudy@comcast.net

09-10-2016, 08:06 PM	#4305
San Diego Ron Registered User Join Date: Nov 2012 Location: San Diego, CA Posts: 54	Re: What did you do to your truck today? Chapter II Well, today I taped and sprayed epoxy primer/sealer. Attached Images

09-10-2016, 10:45 PM	#4306
68 Stepper Registered User Join Date: Jul 2014 Location: Richland Washington Posts: 127	Re: What did you do to your truck today? Chapter II [That is a good buddy! Great loking emblems. QUOTE=74baggedbug;7704909] Buddy made these for me to take the place of the factory c/10 on the fenders[/QUOTE]

09-11-2016, 04:24 AM	#4308
cruisinthe34 Registered User Join Date: Sep 2015 Location: Charleston, WV Posts: 228	Re: What did you do to your truck today? Chapter II Started on the 6" static rear drop. __________________ Steve My Build Thread: http://67-72chevytrucks.com/vboard/s...=morning+glory 1971 C10 Inline 6 250 700R4 "Marlene" 1934 Chevrolet Master Sedan 350 700R4 "Iris" 1941 Ford 1/2 Ton 5.0 H.O Roller C-4 "Rose" 2019 Honda Ridgeline

09-11-2016, 04:24 AM	#4309
cruisinthe34 Registered User Join Date: Sep 2015 Location: Charleston, WV Posts: 228	Re: What did you do to your truck today? Chapter II Started on the 6" static rear drop. __________________ Steve My Build Thread: http://67-72chevytrucks.com/vboard/s...=morning+glory 1971 C10 Inline 6 250 700R4 "Marlene" 1934 Chevrolet Master Sedan 350 700R4 "Iris" 1941 Ford 1/2 Ton 5.0 H.O Roller C-4 "Rose" 2019 Honda Ridgeline

09-11-2016, 02:16 PM	#4310
Possmguts Registered User Join Date: Nov 2014 Location: Columbiana Ohio Posts: 1,210	Re: What did you do to your truck today? Chapter II Went for a little imaginary cruise today... She ran like a champ and I smoked a couple mustangs and a few ricers... Attached Images __________________ "Hey... its only time and money right? Just do it." 67 Short Bed under major construction http://67-72chevytrucks.com/vboard/s...=651356&page=8

09-11-2016, 09:34 PM	#4312
1968aj Registered User Join Date: Apr 2009 Location: houston texas Posts: 1,438	Re: What did you do to your truck today? Chapter II Did some cleaning on the trucks. took them for a short ride one at a time of course. its a long story how I ended up with 3 69 models and really wanted a 68. Attached Images

09-11-2016, 10:02 PM	#4313
everettelane Registered User Join Date: Jul 2015 Location: Cleveland Texas Posts: 109	Re: What did you do to your truck today? Chapter II Built a new trans cross member for my six speed made it so i could run exhaust under it also cut out the rear cross member and welded in plate to run exhaust through it.Pay no attention to the (temporary) fuel lines i had to do that to move the truck, i plan on going stainless tubing. Attached Images

09-12-2016, 07:21 PM	#4314
RodnRudy Senior Member Join Date: Oct 2014 Location: New Palestine In Posts: 930	Re: What did you do to your truck today? Chapter II Yesterday I reinstalled the tail light trim that came with the truck, not 68 correct but I like it and it's cheap like me. Today I reinstalled the door sill plates and hauled the rider to the daughters and mowed her grass. This old girl hauls! Attached Images __________________ Phil "Money is only a tool to create and achieve what you want most in life" PayPal: rodnrudy@comcast.net

09-12-2016, 11:38 PM	#4316
crazyjeenyus Registered User Join Date: Feb 2015 Location: Alberta, Canada Posts: 148	Broke in the cam on the new engine with my newly built run-stand. Attached Images

09-13-2016, 12:50 PM	#4317
VWNate1 Registered User Join Date: Feb 2012 Location: So. Cali. Posts: 2,611	Re: What did you do to your truck today? Chapter II RE : cam breakin ~ what RPM's and how long did you run it ? . __________________ -Nate Geezer '49 3100 235 W/ Muncie SM420 SOLD '69 C/10 shortbed sidemount survivor 250 L6 W/ 350TH

09-13-2016, 02:21 PM	#4318
66clow Registered User Join Date: Jun 2012 Location: Clearwater Beach Florida Posts: 872	Re: What did you do to your truck today? Chapter II I didn't let living in a an apartment keep me from doing a little bodywork also tested out some temporary rattle can colors. May go with the satin blue on the bottom and plastidip the top satin black or just rattle can all of it.

09-13-2016, 05:55 PM	#4319
San Diego Ron Registered User Join Date: Nov 2012 Location: San Diego, CA Posts: 54	Re: What did you do to your truck today? Chapter II Nice truck, I wouldn't raddle can it, Maaco quoted me price of $900 with body work or $300 less without door jams. Want to two-tone mine so going it alone with paint from (Paint For Cars. com) Toms River, N.J. ...$75/$85 per gallon kit with everything. By the way mine is going to be silver on top with Midnight Blue on bottom...about like your color. Attached Images



Register or Log In To remove these advertisements.

09-13-2016, 07:15 PM	#4322
In The Ten Ring Registered User Join Date: Jun 2013 Location: West Virginia Posts: 6,421	Re: What did you do to your truck today? Chapter II I wished I had it back together and running. Does that count?

09-13-2016, 08:24 PM	#4324
TwoFiftyShifter Registered User Join Date: Nov 2008 Location: Gwinnett GA Posts: 1,803	Re: What did you do to your truck today? Chapter II I put new valve cover gaskets on and some hooks in the stake pockets. Drove around some too with my dog. __________________ 1982 K10 SWB 1987 V20 - Sold - Doh! Last edited by TwoFiftyShifter; 09-13-2016 at 08:54 PM.

Register or Log In To remove these advertisements.