Street machine nationals C10 build - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**67cheby** · 02-19-2013, 03:58 PM

Sweet !

OTIS HURTS · 02-19-2013, 04:01 PM

very nice

ddubbs · 02-19-2013, 04:48 PM

Turned out awesome!!!!
Posted via Mobile Device

Slam'ed 72 · 02-21-2013, 10:33 AM

Thanks for all the kind remarks on the shop truck. Can't wait to get her out on the road!!!

Bennett68C10 · 02-21-2013, 01:25 PM

Looks great, can't wait to see some outside pics
Posted via Mobile Device

kdog3121 · 02-24-2013, 07:34 PM

would you mind sharing what size tires you're running on the front and rears?

truck looks great so far.

Slam'ed 72 · 02-28-2013, 05:26 PM

I am running 235/35/20 in the front and a 285/35/22 in the rear. Going to change the front tires to a 245/40/20. It doesn't look right to me.

CC69Rat · 02-28-2013, 05:33 PM

Current sidewall up front - 3.24"

245/40/20 = 3.85" sidewall

285/35 = 3.92" sidewall.

Let me say this is one of my favorite trucks on the forum but I just never commented because I felt like it needed more tire on it. Not saying it doesn't look great as is, but just my taste / opinion and I do agree with you I think it needs more rubber up front. I just didn't want to sound negative.

The reason I put the measurements up there is to say I'd be careful with anything over a 245/40/20 up front because looking at it from the side your front sidewall would be bigger than the back. .. just sayin.

But, I'll mention it again

Killer truck man, but if it were mine I would put a little more tire on it. It would make it ride better too.

Slam'ed 72 · 03-01-2013, 11:40 AM

Looking at a 255/35/20 for the front. That would give me a side wall of 3.513" Vs. the 245/40/20 - 3.858

**lolife99** · 03-01-2013, 01:14 PM

I vote for a 245/40 or a 255/40.
35 series is too short up front.
(my opinion)

CC69Rat · 03-01-2013, 07:07 PM

Are you referring to the SMN in Pigeon Forge TN?

I agree, Id do 245 or 255 40 series. Just for potholes and stuff. Id hate to see you bend a wheel.
Posted via Mobile Device

Number98 · 05-19-2013, 09:24 PM

Any new updates?

Slam'ed 72 · 05-20-2013, 11:26 AM

Finally got a few new pictures.
My new ride height.... I will have more with my new front tires. Ended up going with the 245/40/20... This was a good choice, because it matched the rear side wall height perfect.

Slam'ed 72 · 05-20-2013, 11:31 AM

Here is a couple more of the rear bagged out. I am looking for Ideas for the inside bed... Not sure what to do????? I need to raise my floor up approximately 2" and need to cover it with wood or metal....

Number98 · 05-20-2013, 01:20 PM

Looking sweet man!

Bennett68C10 · 05-20-2013, 03:30 PM

Wow looks awesome
Posted via Mobile Device

Slam'ed 72 · 05-28-2013, 10:36 AM

Wow. Ran into a new issue. I need hood hinges. I changed the tire size in the front and now I cannot drop the truck all the way down.

Any ideas????

I have looked at Fesler build hinges... They don't appear to have a specific C10 application

Just looked at Bult-rite hinges... Not sure???

Thanks.....

**67cheby** · 05-28-2013, 10:37 AM

Porterbuilt

**lolife99** · 05-28-2013, 10:40 AM

Quote:

Originally Posted by Slam'ed 72

Wow. Ran into a new issue. I need hood hinges. I changed the tire size in the front and now I cannot drop the truck all the way down.

Any ideas????

http://www.porterbuiltfabrication.com/?p=355

2002yanks · 06-01-2013, 11:56 AM

i have a set just like the ones pictured above(raw steel how they come). heres a link.
http://67-72chevytrucks.com/vboard/s...=1#post6101824

builtbyKane · 06-01-2013, 01:06 PM

That's a tough looking truck.
Posted via Mobile Device

fastnotch89 · 06-02-2013, 09:50 AM

Looks great layed out.... i guess i need to cut mine up also....

Slam'ed 72 · 07-15-2013, 01:03 PM

Finally on the Road!!!

Zoomin · 07-15-2013, 01:13 PM

Looks awesome!

Bennett68C10 · 07-15-2013, 01:23 PM

Your truck looks awesome, did you spray the satin blue and if so what did you use, or is it just the original patina? Either way it looks great.
Posted via Mobile Device

02-19-2013, 03:58 PM	#26
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Street machine nationals C10 build Sweet ! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

02-19-2013, 04:01 PM	#27
OTIS HURTS Registered User Join Date: Dec 2012 Location: TN Posts: 31	Re: Street machine nationals C10 build very nice

02-19-2013, 04:48 PM	#28
ddubbs Registered User Join Date: Feb 2011 Location: Alaska Posts: 461	Re: Street machine nationals C10 build Turned out awesome!!!! Posted via Mobile Device __________________ LIFTED OR LOW THE ONLY WAY TO GO!!!! Check out my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=517346 Projects 56 Chevy pickup Porterbuilt FR/RR dropmembers

02-21-2013, 10:33 AM	#29
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Thanks for all the kind remarks on the shop truck. Can't wait to get her out on the road!!!

02-21-2013, 01:25 PM	#30
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Street machine nationals C10 build Looks great, can't wait to see some outside pics Posted via Mobile Device __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

02-24-2013, 07:34 PM	#31
kdog3121 Registered User Join Date: Mar 2009 Location: weymouth, MA Posts: 66	Re: Street machine nationals C10 build would you mind sharing what size tires you're running on the front and rears? truck looks great so far.

02-28-2013, 05:26 PM	#32
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build I am running 235/35/20 in the front and a 285/35/22 in the rear. Going to change the front tires to a 245/40/20. It doesn't look right to me.

02-28-2013, 05:33 PM	#33
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,208	Re: Street machine nationals C10 build Current sidewall up front - 3.24" 245/40/20 = 3.85" sidewall 285/35 = 3.92" sidewall. Let me say this is one of my favorite trucks on the forum but I just never commented because I felt like it needed more tire on it. Not saying it doesn't look great as is, but just my taste / opinion and I do agree with you I think it needs more rubber up front. I just didn't want to sound negative. The reason I put the measurements up there is to say I'd be careful with anything over a 245/40/20 up front because looking at it from the side your front sidewall would be bigger than the back. .. just sayin. But, I'll mention it again Killer truck man, but if it were mine I would put a little more tire on it. It would make it ride better too. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-01-2013, 11:40 AM	#34
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Looking at a 255/35/20 for the front. That would give me a side wall of 3.513" Vs. the 245/40/20 - 3.858

03-01-2013, 01:14 PM	#35
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,703	Re: Street machine nationals C10 build I vote for a 245/40 or a 255/40. 35 series is too short up front. (my opinion) __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

03-01-2013, 07:07 PM	#36
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,208	Re: Street machine nationals C10 build Are you referring to the SMN in Pigeon Forge TN? I agree, Id do 245 or 255 40 series. Just for potholes and stuff. Id hate to see you bend a wheel. Posted via Mobile Device __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

05-19-2013, 09:24 PM	#37
Number98 Prestige Worldwide Join Date: Feb 2001 Location: Worldwide Posts: 2,553	Re: Street machine nationals C10 build Any new updates?

05-20-2013, 11:26 AM	#38
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Finally got a few new pictures. My new ride height.... I will have more with my new front tires. Ended up going with the 245/40/20... This was a good choice, because it matched the rear side wall height perfect. Attached Images

05-20-2013, 11:31 AM	#39
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Here is a couple more of the rear bagged out. I am looking for Ideas for the inside bed... Not sure what to do????? I need to raise my floor up approximately 2" and need to cover it with wood or metal.... Attached Images

05-20-2013, 01:20 PM	#40
Number98 Prestige Worldwide Join Date: Feb 2001 Location: Worldwide Posts: 2,553	Re: Street machine nationals C10 build Looking sweet man!



Register or Log In To remove these advertisements.

05-20-2013, 03:30 PM	#41
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Street machine nationals C10 build Wow looks awesome Posted via Mobile Device __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

05-28-2013, 10:36 AM	#42
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Wow. Ran into a new issue. I need hood hinges. I changed the tire size in the front and now I cannot drop the truck all the way down. Any ideas???? I have looked at Fesler build hinges... They don't appear to have a specific C10 application Just looked at Bult-rite hinges... Not sure??? Thanks.....

05-28-2013, 10:37 AM	#43
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Street machine nationals C10 build Porterbuilt __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

06-01-2013, 11:56 AM	#45
2002yanks Registered User Join Date: Sep 2010 Location: Auburn NY Posts: 1,470	Re: Street machine nationals C10 build i have a set just like the ones pictured above(raw steel how they come). heres a link. http://67-72chevytrucks.com/vboard/s...=1#post6101824 __________________ My build thread!! http://67-72chevytrucks.com/vboard/s...d.php?t=474018

06-01-2013, 01:06 PM	#46
builtbyKane Registered User Join Date: Oct 2012 Location: mountain home, AR Posts: 794	Re: Street machine nationals C10 build That's a tough looking truck. Posted via Mobile Device __________________ Project Double Tap http://67-72chevytrucks.com/vboard/s...d.php?t=555901 69 Olive Verde http://67-72chevytrucks.com/vboard/s...d.php?t=734720

06-02-2013, 09:50 AM	#47
fastnotch89 Registered User Join Date: Apr 2013 Location: Clover,SC Posts: 142	Re: Street machine nationals C10 build Looks great layed out.... i guess i need to cut mine up also....

07-15-2013, 01:03 PM	#48
Slam'ed 72 Registered User Join Date: Jul 2012 Location: Steeleville, IL Posts: 47	Re: Street machine nationals C10 build Finally on the Road!!! Attached Images

07-15-2013, 01:13 PM	#49
Zoomin Man of Mini-Talents Join Date: Sep 2009 Location: Oklahoma City, OK Posts: 4,295	Re: Street machine nationals C10 build Looks awesome! __________________ Steve Project - Ruth 66 Skylark Project - Lola 60 Biscayne Project - Iron Ox 54 GMC 100 Project - Darth 69 Camaro

07-15-2013, 01:23 PM	#50
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Street machine nationals C10 build Your truck looks awesome, did you spray the satin blue and if so what did you use, or is it just the original patina? Either way it looks great. Posted via Mobile Device __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10 Last edited by Bennett68C10; 07-15-2013 at 03:21 PM.

Register or Log In To remove these advertisements.