Joined the Short Wheelbase Club *69 Tahoe Project* - Page 26 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

gringoloco · 01-16-2008, 04:56 PM

So what changes did you make out back besides new shocks? Have you found a suitable sway bar yet. (taking notes)

You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn. They kinda have a 'sweet spot' when the pads are just broken in and the clearances are good on both sides...

babyblueoval · 01-16-2008, 05:20 PM

[QUOTE=gringoloco;2531520]
You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn. QUOTE]

So gringo, which calipers are you gonna use on yours?

gringoloco · 01-20-2008, 06:50 AM

Quote:

Originally Posted by babyblueoval

Quote:

Originally Posted by gringoloco

You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn.

So gringo, which calipers are you gonna use on yours?

Impala. I will figure out the e-brake later...

Frizzle Fry · 01-16-2008, 08:42 PM

Quote:

Originally Posted by gringoloco

So what changes did you make out back besides new shocks? Have you found a suitable sway bar yet. (taking notes)

You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn. They kinda have a 'sweet spot' when the pads are just broken in and the clearances are good on both sides...

The new shocks are longer and tipped in at an angle now instead of vertical giving me full travel without shock induced limitations. The ride probably feels a little more compliant due to the bar removal as well. I'm going to go with the hellwig trailing arm bar.

I noticed when I installed the calipers that they wanted to push the rotors and axles into the housing as the bolts were tightened. I figured I'd get it all bled and cycled a few times and see where it settles. But after driving it I can definately feel and hear the drag so I'll shim them out a little.

502tripower · 01-19-2008, 11:41 AM

Mike I just read this whole post. Man what a project....

Next time I am in Portland I am going to want to stop by and meet you and check out your rigs. I have some mods I want to make to my 63' as well that are subtle and a head scratcher. Good job keep the progress pics coming.

Bishops Trucks · 01-20-2008, 01:14 AM

I'll work on the rendering for you tomorrow. I forgot I have to take the wife to some freakin Ball tonight. OH Boy, I'm going to have some fun.

joe231 · 01-22-2008, 11:11 PM

AMAZING thread!! other than that I'm speechless

oh and, Primus Rocks!!

meathead95 · 01-23-2008, 04:35 AM

ok

jkaylor68gmc · 01-23-2008, 04:59 AM

nice. Friz, got any new pics?

Brought the '51 home.

**Hart_Rod** · 02-18-2008, 03:10 AM

FF, we need an update,

.

Frizzle Fry · 02-18-2008, 01:59 PM

Quote:

Originally Posted by Hart_Rod

FF, we need an update,

.

Been traveling (might even visit the querque soon) and working on a house I'm selling, but... I did POR-15 my notch and aquire the rest of the rear disc parts (pass cable and both flex lines).

**Hart_Rod** · 02-18-2008, 10:21 PM

Quote:

Originally Posted by Frizzle Fry

Been traveling (might even visit the querque soon) and working on a house I'm selling, but... I did POR-15 my notch and aquire the rest of the rear disc parts (pass cable and both flex lines).

I got my disc brackets and will put it all together when I get the rest of the pieces gathered up. Just let me know when you're coming in, we'll go check out some NM metal,

.

franky69c10 · 02-18-2008, 04:54 AM

looks real good

Frizzle Fry · 03-05-2008, 04:15 AM

A couple updates:

Pics of the POR-15'd notch. I used cheapo foam brushes (one time use) and they shed so the finish is speckled but it's all covered and protected (recommend spending a couple more cents for the "quality" brushes if you go that route):

The summit drilled/slotted rotors started rusting from non-use so I pulled them off and gave them a light sanding/cleaning. I found that the holes and slots were gonna be a PITA keep from corroding so I chose to POR-15 them too

We'll see if it stays there. Might need the high temp stuff.

...and got the pass-side e-brake cable routed:

5150 · 03-05-2008, 05:03 AM

Looks good, glad to see you back at it.

babyblueoval · 03-05-2008, 05:28 AM

Them rotors sure look purdy.

1LoC10 · 03-05-2008, 05:32 AM

looking real good... i dont see why the por 15 wouldnt stay there, nothing going to rub it or anything

Frizzle Fry · 03-05-2008, 07:11 AM

Thanks guys

Quote:

Originally Posted by 1LoC10

looking real good... i dont see why the por 15 wouldnt stay there, nothing going to rub it or anything

Heat is my concern. Guess we'll see.

**Hart_Rod** · 03-05-2008, 07:44 AM

Quote:

Originally Posted by Frizzle Fry

Thanks guys

Heat is my concern. Guess we'll see.

I know people who have used in on engines with no problems. Do you have some closer shots of the new rubber lines? Thanks,

texanidiot25 · 03-05-2008, 07:55 AM

Your gonna get surface rust on the disks no matter what if you don't drive it.

But the moment you get on the brakes, it's all blown off.

It's the 'Burbs way of saying "Drive me"

Frizzle Fry · 03-05-2008, 08:25 AM

Quote:

Originally Posted by Hart_Rod

I know people who have used in on engines with no problems. Do you have some closer shots of the new rubber lines? Thanks,

You're the hose police

They're not on yet. Still need to pick up the banjo bolts and I'm thinking I'll just go ahead and replace the steel lines from the T out to the flex lines.

Quote:

Originally Posted by texanidiot25

Your gonna get surface rust on the disks no matter what if you don't drive it.

But the moment you get on the brakes, it's all blown off.

It's the 'Burbs way of saying "Drive me"

I know, you're right. The problem is when you have no rear floor and wet roads...

I agree on the rust too, but those holes and slots would not be cleaned by the pads.

**Hart_Rod** · 03-05-2008, 11:20 PM

Quote:

Originally Posted by Frizzle Fry

You're the hose police

They're not on yet. Still need to pick up the banjo bolts and I'm thinking I'll just go ahead and replace the steel lines from the T out to the flex lines.

Just looking out for you.....

. I picked my banjo bolts up at the Chevy dealership. Probably could have gotten them elsewhere, but I know I got the correct ones. I'll be back in FL in 2 weeks and then I get to play with new brakes, new headers and maybe a small engine upgrade,

,

.

wagonhoe · 03-06-2008, 01:11 AM

Ya know..., if ol' Friz could bottle that motivation and resourcefulness he has flowing from every pore, he could be a rich man...

gringoloco · 03-05-2008, 08:22 AM

I painted my slots too. I hate dirty slots... or do I?

**FRENCHBLUE72** · 03-06-2008, 08:38 AM

Hey mike you have any pic of those headders installed?

01-16-2008, 04:56 PM	#1
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,920	Re: Joined the Short Wheelbase Club 69 Tahoe Project So what changes did you make out back besides new shocks? Have you found a suitable sway bar yet. (taking notes) You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn. They kinda have a 'sweet spot' when the pads are just broken in and the clearances are good on both sides... __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

01-16-2008, 05:20 PM	#2
babyblueoval Registered User Join Date: Apr 2006 Location: Arkansas Posts: 835	Re: Joined the Short Wheelbase Club 69 Tahoe Project [QUOTE=gringoloco;2531520] You may find it difficult to quiet those Camaro brakes. I had those same calipers on my '94 TA. They always want to rub the rotor when you have brand new pads as well as when they are well worn. QUOTE] So gringo, which calipers are you gonna use on yours? __________________ Jim '71 Blazer-Porterbuilt Dropmember C4/LS1/6L80E '57 VW beetle - Oct. 2006 Hot VW's pg. 87 - 350hp intercooled, turbocharged, EFI 2.3liter and 5spd in the works '87 BMW 325i - daily driver

01-19-2008, 11:41 AM	#5
502tripower Registered User Join Date: Jan 2008 Location: Satsop, WA Posts: 606	Re: Joined the Short Wheelbase Club 69 Tahoe Project Mike I just read this whole post. Man what a project.... Next time I am in Portland I am going to want to stop by and meet you and check out your rigs. I have some mods I want to make to my 63' as well that are subtle and a head scratcher. Good job keep the progress pics coming. __________________ 1963' Chev Custom Cab 502, 67' 435hp 3X2 intake, 9" 4:30 Posi 1961 Impala SS 348/350 4-speed 3:70 Posi 1961 Bel-Air Bubble Top 283 Turboglide soon to have a 348 3X2 4-speed 1950 17' Fairliner twin cockpit barrel stern 312 Y block 1X1 intake Borg Warner 1:1 gear 1957 Fleetform 14' twin cockpit barrel stern 1969 BP-125 Merc 1949 Transitier 3-wheel forklift Crosley 4-Banger 98' FXD 2002 2500HD

01-20-2008, 01:14 AM	#6
Bishops Trucks KEEP ON TRUCKIN' Join Date: Jun 2005 Location: Sterling, Va. Posts: 5,731	Re: Joined the Short Wheelbase Club 69 Tahoe Project I'll work on the rendering for you tomorrow. I forgot I have to take the wife to some freakin Ball tonight. OH Boy, I'm going to have some fun. __________________ JIM '97 GMC Sierra K1500 '95 Chevy Silverado C1500 '71 Cheyenne Z71 / LT1 & 4-Speed SWB K/10 Father/Son Project http://www.youtube.com/watch?v=4l689JKXPnA http://67-72chevytrucks.com/vboard/payments.php "LIVIN' FREE FOREVER"

01-22-2008, 11:11 PM	#7
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: Joined the Short Wheelbase Club 69 Tahoe Project AMAZING thread!! other than that I'm speechless oh and, Primus Rocks!! Last edited by joe231; 01-22-2008 at 11:12 PM.

01-23-2008, 04:35 AM	#8
meathead95 computer illiterate Join Date: Jan 2001 Location: Des Moines, IA Posts: 6,446	Re: Joined the Short Wheelbase Club 69 Tahoe Project ok __________________ 72 2wd blazer 72 swb 4x4

01-23-2008, 04:59 AM	#9
jkaylor68gmc Senior Member Join Date: Dec 2005 Location: TN Posts: 2,448	Re: Joined the Short Wheelbase Club 69 Tahoe Project nice. Friz, got any new pics? Brought the '51 home. __________________ 1947 International KB-1 1957 Chevy Bel-Air riding low 1962 swb fleetside 2002 Chevrolet Silverado 7-inch lift on 35 Daily driver 2016 Chevy Tahoe Better halves ride

02-18-2008, 03:10 AM	#10
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,837	Re: Joined the Short Wheelbase Club 69 Tahoe Project FF, we need an update, . __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

02-18-2008, 04:54 AM	#13
franky69c10 chevy runs deep Join Date: Mar 2006 Location: PHOENIX AZ Posts: 1,074	Re: Joined the Short Wheelbase Club 69 Tahoe Project looks real good __________________ RAIDER NATION 1969 c10 swb soon 2 b on the road... My LWB is a SWB now http://67-72chevytrucks.com/vboard/s...d.php?t=498241

03-05-2008, 04:15 AM	#14
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: Joined the Short Wheelbase Club 69 Tahoe Project A couple updates: Pics of the POR-15'd notch. I used cheapo foam brushes (one time use) and they shed so the finish is speckled but it's all covered and protected (recommend spending a couple more cents for the "quality" brushes if you go that route): The summit drilled/slotted rotors started rusting from non-use so I pulled them off and gave them a light sanding/cleaning. I found that the holes and slots were gonna be a PITA keep from corroding so I chose to POR-15 them too We'll see if it stays there. Might need the high temp stuff. ...and got the pass-side e-brake cable routed:

03-05-2008, 05:03 AM	#15
5150 C10 Club Tennessee Join Date: Mar 2003 Location: White House, TN 37188 Posts: 8,281	Re: Joined the Short Wheelbase Club 69 Tahoe Project Looks good, glad to see you back at it. __________________ Bryan www.gmtruckshow.com Project "Andes"-Halen's First Truck Project: Patina Burb for he is God’s servant for your good. But if you do wrong, be afraid, for he does not bear the sword in vain. For he is the servant of God, an avenger who carries out God’s wrath on the wrongdoer. Romans 13:4

03-05-2008, 05:28 AM	#16
babyblueoval Registered User Join Date: Apr 2006 Location: Arkansas Posts: 835	Re: Joined the Short Wheelbase Club 69 Tahoe Project Them rotors sure look purdy. __________________ Jim '71 Blazer-Porterbuilt Dropmember C4/LS1/6L80E '57 VW beetle - Oct. 2006 Hot VW's pg. 87 - 350hp intercooled, turbocharged, EFI 2.3liter and 5spd in the works '87 BMW 325i - daily driver

03-05-2008, 05:32 AM	#17
1LoC10 Insert Title Here Join Date: Feb 2006 Location: Dyer, Indiana Posts: 5,679	Re: Joined the Short Wheelbase Club 69 Tahoe Project looking real good... i dont see why the por 15 wouldnt stay there, nothing going to rub it or anything __________________ BOBBY _69 SWB_ 1000 pics of 67-72's>> http://s193.photobucket.com/albums/z...-72/?start=all <<

03-05-2008, 07:55 AM	#20
texanidiot25 Eat My Rust Join Date: Jan 2007 Location: Cypress, Texas Posts: 3,362	Re: Joined the Short Wheelbase Club 69 Tahoe Project Your gonna get surface rust on the disks no matter what if you don't drive it. But the moment you get on the brakes, it's all blown off. It's the 'Burbs way of saying "Drive me" Last edited by texanidiot25; 03-05-2008 at 07:55 AM.

03-06-2008, 01:11 AM	#23
wagonhoe Registered User Join Date: Dec 2004 Location: San Diego, Is there anywhere else? Posts: 125	Re: Joined the Short Wheelbase Club 69 Tahoe Project Ya know..., if ol' Friz could bottle that motivation and resourcefulness he has flowing from every pore, he could be a rich man... __________________ 1969 C10 Suburban, 396cid, Turbo 400, 9" F***, Disk brakes all around 1968 C10 Suburban, 350cid, 700R4, bent frame 1968 C20 Suburban, no motor, trans or interior (SOLD!) 1953 Packard Ambulance 1992 Caprice wagon



Register or Log In To remove these advertisements.

03-05-2008, 08:22 AM	#24
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,920	Re: Joined the Short Wheelbase Club 69 Tahoe Project I painted my slots too. I hate dirty slots... or do I? __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy Last edited by gringoloco; 03-05-2008 at 08:22 AM.

03-06-2008, 08:38 AM	#25
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: Joined the Short Wheelbase Club 69 Tahoe Project Hey mike you have any pic of those headders installed? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

Register or Log In To remove these advertisements.