CA 250 engine and 3-speed manual trans

[mikey2409]

Originally Posted by sacto67

I gave the carbs to a friend to try and sell them at a swap meet. He told me one of them sold, he doesn't know which one. I'll find out tomorro which two aare still available.

Sounds good just keep me posted thanks
Posted via Mobile Device

[sacto67]

Originally Posted by ChevyCruizer

is there any chance you have the oil dip stick. I checked my oil when I got mine out of storage and went for a ride and i left it on the inner fenderwell when I drove off. I didnt realize it until I went for an oil change and by that time it was gone off the side of the road. I do not need the tube, just the pull out dip stick. Shipping would be 89121.

Thanks, John

Here is the picture. How does $15 shipped sound.

[sfcharr]

I'll take them! Can you PM me for payment info?

[sfcharr]

Originally Posted by sacto67

Here are the pictures finally. I wasn't sure if you wanted just the motor mounts or the motor mount brackets that bolt to the motor. I looked on Ebay and found some finished auctions for similar parts and it's looking like $70 shipped would be about what they all sold together minus a few bucks.

Forgot to quote message in my reply. I'll take them. PM me for payment information. Thanks again!

[sacto67]

Pm sent

[ChevyCruizer]

Sounds good. Could you do me one favor and measure the length of the actual dip stick part (not including the handel or part that goes over the tube). I ordered one from eBay and it was way to short. I dont have the measurements of the incorrect one one me but will check when I get off work.

Thanks, John

Originally Posted by sacto67

Here is the picture. How does $15 shipped sound.

[sacto67]

Originally Posted by ChevyCruizer

Sounds good. Could you do me one favor and measure the length of the actual dip stick part (not including the handel or part that goes over the tube). I ordered one from eBay and it was way to short. I dont have the measurements of the incorrect one one me but will check when I get off work.

Thanks, John

No problem I'll check it when I get home and let you know.

[sacto67]

Originally Posted by ChevyCruizer

Sounds good. Could you do me one favor and measure the length of the actual dip stick part (not including the handel or part that goes over the tube). I ordered one from eBay and it was way to short. I dont have the measurements of the incorrect one one me but will check when I get off work.

Thanks, John

Sorry it took me so long, it is just barely under 14".

[FTP]

is that a PS pump i see in there? will you sell the power steering setup?

[sacto67]

Originally Posted by FTP

is that a PS pump i see in there? will you sell the power steering setup?

Nope, not a power steering pump, it's an emissions pump.

[sacto67]

The carb and aircleaner are still available.

[70blackfish]

how much for the carb shipped to 93063?

[sacto67]

Originally Posted by 70blackfish

how much for the carb shipped to 93063?

PM sent

[sfcharr]

How much for the Air Cleaner complete shipped to 45840?

[70blackfish]

how much for the long block?

[sacto67]

Originally Posted by 70blackfish

how much for the long block?

I was planning on scrapping it for about $50.....how does $40 sound?

[sacto67]

Originally Posted by sfcharr

How much for the Air Cleaner complete shipped to 45840?

$40 shipped.

[sfcharr]

Originally Posted by sacto67

$40 shipped.

Is the air cleaner complete with all the associated tubes? I'll take it if it does. PM me.

[sacto67]

Originally Posted by sfcharr

Is the air cleaner complete with all the associated tubes? I'll take it if it does. PM me.

Sure, I'll include that stuff. PM sent

[blkcorvair]

If air cleaner becomes available again I will take it.

[sacto67]

Originally Posted by 70blackfish

how much for the long block?

$20??

[70blackfish]

its a good deal , but i will pass going to go with a small block......

[sfcharr]

I'm in need of the throttle/carb brackets for this motor. Is there any chance you might have this? How about the clutch pivot bracket that bolts to the block? Let me know, Thanks

[sacto67]

Originally Posted by sfcharr

I'm in need of the throttle/carb brackets for this motor. Is there any chance you might have this? How about the clutch pivot bracket that bolts to the block? Let me know, Thanks

I should still have all of those parts. I'll post what I have with pictures. But it'll probably be tomorrow night, pulling a 16 hour day today at work.

[sfcharr]

OK, sounds good, I'll wait for the pictures