85 C10 Project "Walking Horse" - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ultrahd4me · 09-06-2016, 04:08 PM

If your rubbing with a 40 upfront you have more than 5" of drop or really weak springs. It sounds you got a 3" drop spring which you may have 5.5" of drop. Take your stock springs and remove one round,then grind a flat on the bottom, swap sides and try them.

BB72CHEVKT · 09-06-2016, 04:13 PM

Quote:

Originally Posted by ultrahd4me

If your rubbing with a 40 upfront you have more than 5" of drop or really weak springs. It sounds you got a 3" drop spring which you may have 5.5" of drop. Take your stock springs and remove one round,then grind a flat on the bottom, swap sides and try them.

Well I just ordered the new 3/4 ton springs and will give them a try. Other folks with the McGaughys kit are running into the same problem. I should have skipped the kit because we didn't use the notch either. I listened maybe just not close enough. LMAO. I think I will hold off on new tires until I see what the new springs are like. I have to by new tires anyways since I stole these off the burb.

ultrahd4me · 09-06-2016, 04:18 PM

I've been down that road before. You may not be happy with the 3/4ton springs and 2-1/2 spindles, you only get about 1-1/2 drop cutting them. I used a 3" spindle and removed 1 round on my blue truck. I ran a 45 series tire on the front.

BB72CHEVKT · 09-06-2016, 04:24 PM

I got the order cancelled before the springs shipped so I will try cutting the stock coil first.

BB72CHEVKT · 09-08-2016, 09:37 AM

Quote:

Originally Posted by ultrahd4me

I've been down that road before. You may not be happy with the 3/4ton springs and 2-1/2 spindles, you only get about 1-1/2 drop cutting them. I used a 3" spindle and removed 1 round on my blue truck. I ran a 45 series tire on the front.

Sorry to clutter your thread on your beautiful truck. Well I changed my mind again and we tried the 3/4 ton springs with a coil cut for two inch drop and I am WAY higher now than I was before and it looks like crap. It rides great with the stiff spring it is just way to high. The rear is tucking and the front has a huge gap.

**Desert1957** · 09-11-2016, 07:05 PM

Bobby,

I tried, but was out bid with 2 seconds left to go.....

ultrahd4me · 09-11-2016, 07:36 PM

I thought you were going to get it. The buyer has already made the deposit, but if there was to be any problems with the payment I'll let you know. Thanks for bidding and I've got a few more coming soon.

UKNOWME · 09-11-2016, 09:07 PM

I knew I was far off but I was tapped out at 9200. Glad you got it sold!

ultrahd4me · 09-11-2016, 09:37 PM

Thank you for bidding. The truck is heading to New Orleans.

UKNOWME · 09-11-2016, 09:52 PM

Sweet!

**Desert1957** · 09-12-2016, 07:33 AM

Quote:

Originally Posted by ultrahd4me

I thought you were going to get it. The buyer has already made the deposit, but if there was to be any problems with the payment I'll let you know. Thanks for bidding and I've got a few more coming soon.

Thanks, looking forward to the next one.

**N2TRUX** · 09-12-2016, 10:06 AM

Congratulations buddy, that one went quickly. Someone got a really clean truck.

BB72CHEVKT · 09-12-2016, 01:06 PM

Congrats on the sale. It was a beautiful truck.

Tadow12 · 09-25-2016, 12:28 AM

ULTRAHD4ME... where sis you order your dash pad from? Thanks

NewType72 · 09-25-2016, 10:19 PM

Congrats on the sale

ultrahd4me · 09-26-2016, 07:56 AM

Quote:

Originally Posted by Tadow12

ULTRAHD4ME... where sis you order your dash pad from? Thanks

The dash pad came from Cheyenne truck parts.

ultrahd4me · 09-26-2016, 07:59 AM

Quote:

Originally Posted by BB72CHEVKT

Congrats on the sale. It was a beautiful truck.

Quote:

Originally Posted by NewType72

Congrats on the sale

Thanks guys. Just wait and see what I unveil next week.

**N2TRUX** · 09-28-2016, 09:43 AM

Quote:

Originally Posted by ultrahd4me

Thanks guys. Just wait and see what I unveil next week.

Text me a sneak peek.

ultrahd4me · 09-28-2016, 10:36 AM

Only for you

BB72CHEVKT · 09-28-2016, 05:08 PM

Quote:

Originally Posted by ultrahd4me

Only for you

Article 12 Section 17 of the board rules state very clearly that this is not allowed.

**N2TRUX** · 09-29-2016, 10:23 AM

Quote:

Originally Posted by ultrahd4me

Only for you

Thanks buddy

Quote:

Originally Posted by BB72CHEVKT

Article 12 Section 17 of the board rules state very clearly that this is not allowed.

Apparently you didnt read the fine print. It states that small partial view sneak peaks are allowed.

BTW- The next one is going to be killer.

BB72CHEVKT · 09-30-2016, 11:03 AM

Quote:

Originally Posted by N2TRUX

Thanks buddy

Apparently you didnt read the fine print. It states that small partial view sneak peaks are allowed.

BTW- The next one is going to be killer.

The fine print gets you every time.

ultrahd4me · 09-30-2016, 02:32 PM

Its going to be about 2 weeks before I really get going on it. I plan on starting on new build thread when I do, but I'll give a little tease to keep it interesting.

77c10 · 09-30-2016, 02:56 PM

Quote:

Originally Posted by ultrahd4me

Its going to be about 2 weeks before I really get going on it. I plan on starting on new build thread when I do, but I'll give a little tease to keep it interesting.

Bobby, I need a picture of your cold air intake. Mainly the filter end of it, please.

BB72CHEVKT · 10-04-2016, 06:04 PM

I'm in.

09-06-2016, 04:08 PM	#76
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" If your rubbing with a 40 upfront you have more than 5" of drop or really weak springs. It sounds you got a 3" drop spring which you may have 5.5" of drop. Take your stock springs and remove one round,then grind a flat on the bottom, swap sides and try them. __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

09-06-2016, 04:18 PM	#78
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" I've been down that road before. You may not be happy with the 3/4ton springs and 2-1/2 spindles, you only get about 1-1/2 drop cutting them. I used a 3" spindle and removed 1 round on my blue truck. I ran a 45 series tire on the front. Attached Images __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

09-06-2016, 04:24 PM	#79
BB72CHEVKT Junior Member Join Date: Mar 2007 Location: Hideaway, TX Posts: 4,948	Re: 85 C10 Project "Walking Horse" I got the order cancelled before the springs shipped so I will try cutting the stock coil first. __________________ 71 Suburban 350/700R4 Project Trixie 72 CHEVY,Highlander,SWB,396,T400 Last edited by BB72CHEVKT; 09-06-2016 at 05:27 PM. Reason: change info

09-11-2016, 07:05 PM	#81
Desert1957 Registered User Join Date: Apr 2009 Location: New Freedom Pa. Posts: 1,335	Re: 85 C10 Project "Walking Horse" Bobby, I tried, but was out bid with 2 seconds left to go..... __________________ Desert

09-11-2016, 07:36 PM	#82
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" I thought you were going to get it. The buyer has already made the deposit, but if there was to be any problems with the payment I'll let you know. Thanks for bidding and I've got a few more coming soon. __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

09-11-2016, 09:07 PM	#83
UKNOWME Registered User Join Date: Aug 2012 Location: Clovis, NM Posts: 2,705	Re: 85 C10 Project "Walking Horse" I knew I was far off but I was tapped out at 9200. Glad you got it sold! __________________ 2018 Audi S5- wife's ride 1980 Chevy Scottsdale http://67-72chevytrucks.com/vboard/s...d.php?t=543511 1981 Chevy Silverado- in pieces 1964 Chevy c10 2017 Jeep Wrangler JKU

09-11-2016, 09:37 PM	#84
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" Thank you for bidding. The truck is heading to New Orleans. __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

09-11-2016, 09:52 PM	#85
UKNOWME Registered User Join Date: Aug 2012 Location: Clovis, NM Posts: 2,705	Re: 85 C10 Project "Walking Horse" Sweet! __________________ 2018 Audi S5- wife's ride 1980 Chevy Scottsdale http://67-72chevytrucks.com/vboard/s...d.php?t=543511 1981 Chevy Silverado- in pieces 1964 Chevy c10 2017 Jeep Wrangler JKU

09-12-2016, 10:06 AM	#87
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: 85 C10 Project "Walking Horse" Congratulations buddy, that one went quickly. Someone got a really clean truck. __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

09-12-2016, 01:06 PM	#88
BB72CHEVKT Junior Member Join Date: Mar 2007 Location: Hideaway, TX Posts: 4,948	Re: 85 C10 Project "Walking Horse" Congrats on the sale. It was a beautiful truck. __________________ 71 Suburban 350/700R4 Project Trixie 72 CHEVY,Highlander,SWB,396,T400

09-25-2016, 12:28 AM	#89
Tadow12 Registered User Join Date: Jun 2016 Location: leesville la Posts: 2	Re: 85 C10 Project "Walking Horse" ULTRAHD4ME... where sis you order your dash pad from? Thanks

09-25-2016, 10:19 PM	#90
NewType72 Registered User Join Date: Feb 2012 Location: turlock Posts: 2,177	Re: 85 C10 Project "Walking Horse" Congrats on the sale __________________ Project NewType 1972 Chevy C/10 Cheyenne Super ( Daily Driven Showtruck ) http://67-72chevytrucks.com/vboard/s...d.php?t=507903 Project Great Grandpa's Legacy 1973 Chevy C/10 Cheyenne ( Current daily driver collecting big time parts ) http://67-72chevytrucks.com/vboard/s...89#post7084289 - Dylan (209)-985-7721

09-28-2016, 10:36 AM	#94
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" Only for you __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

09-30-2016, 02:32 PM	#98
ultrahd4me Registered User Join Date: Dec 2006 Location: Gallatin, Tn Posts: 676	Re: 85 C10 Project "Walking Horse" Its going to be about 2 weeks before I really get going on it. I plan on starting on new build thread when I do, but I'll give a little tease to keep it interesting. Attached Images __________________ Follow me on Instagram: @midtennc10 Youtube channel: Midtennc10

10-04-2016, 06:04 PM	#100
BB72CHEVKT Junior Member Join Date: Mar 2007 Location: Hideaway, TX Posts: 4,948	Re: 85 C10 Project "Walking Horse" I'm in. __________________ 71 Suburban 350/700R4 Project Trixie 72 CHEVY,Highlander,SWB,396,T400



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.