What did you do to your truck today.The 3rd chapter - Page 76 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Accelo · 06-03-2021, 06:08 PM

In my prior life I have installed compression fittings on a 10,000 psi system.

cab4word67 · 06-03-2021, 11:50 PM

Got the truck on the hoist today, box going on tomarrow, new 6" drop is installed and the flip kit/C notch has been done. Now I need to remanufacture the tilt hinges and reinstall the drivetrain. Would like to be done by end of month

67C10Step · 06-04-2021, 08:21 AM

cab,
Wow! Interesting. Did you take the 4x4 in your avatar and make it 2wd? Love the blue.

**Already Gone** · 06-05-2021, 03:29 AM

Had my 255/60 17 inch Bridgestones delivered, Fed Ex contractor left like this, that will be going on my truck probably next year. Now to save for the Torque Thrusts.

72c20customcamper · 06-06-2021, 07:40 PM

72 died on me today in the driveway. Starter must have a dead short tried jumping the solenoid with the tester starter button . Nothing and the button got hot quick. So I have a new one on the way as it was under warranty but I’m done with DBElectric . 3 in two years on 2 different vehicles. So I ordered a Powermaster mini .

I also tried one of the M/T wheels that came off the Tacoma on the 68 . Pain in the butt sanding them to this finish by hand ,may just sand with 400 and paint them black .

cab4word67 · 06-06-2021, 08:58 PM

Quote:

Originally Posted by 67C10Step

cab,
Wow! Interesting. Did you take the 4x4 in your avatar and make it 2wd? Love the blue.

Thanks, no the Avitar is same truck 2 wheel drive with 5"custom lift, 3" body lift and 1 ton ft coils, ran 5" blocks in back with leafs. Ran this way 38 years. The lift started with 15 x38 ground hogs then went to Cepek FunCountrys 17x 40x 15s, ran 3 sets and last the 16x36x15s . now going down to the ground
Also there is 3 coats of purple pearl on top of that blue.

**pjmoreland** · 06-06-2021, 08:43 PM

I completed several small projects today, some of which have been on my to-do list for a long time:

Replaced the output seal on my recently rebuilt 700R4. Either I damaged it or it was defective. Went with a GM seal this time.

Made a mirror image tailpipe hanger bracket for a full length exhaust system I'm planning on getting. Also installed stock hangers on both sides of the chassis in the middle of the truck

Installed a replacement hood hinge I painted yesterday. The original Hinge was bent sideways enough that the open limit stop no longer worked.

Painted and installed a set of shorty 5/16 body screws in the left inner fender brace. These screws are hard to find.

**Rich72C10** · 06-09-2021, 03:00 PM

Got tint and clear windshield over with tint visor!

Now I’m all set for the Texas sun and my trip up to East Texas!

**Rich72C10** · 06-10-2021, 03:20 PM

Made my 300 drive to Kilgore! Truck ran like a dream, 13.5 mpg going 65 ~ 75 and through tons of little towns on US hwy 79!

Also daughter had a good nap - kids can sleep anywhere ;-)

**70cst** · 06-10-2021, 04:48 PM

My refurbished CB came in today ...

**71CHEVYSHORTBED402** · 06-10-2021, 11:03 PM

Quote:

Originally Posted by 70cst

My refurbished CB came in today ...

NICE!

After waiting months for parts long story & the COVID ecomoney

I was able to install the coolant assembly and that. Anyone ever notice a fan's not center inside a shroud, at least BBC? My fan is about 2" off the original shroud on the LH side and just 1/2" on the RH side. Looks about even up & down. That one threw me, but from different angles the core support is square the cab within 1/10" at most. OT, I think the center hole in the dash for a dash pad is center the cab, for what worth. Once I found that there are other indicators, such as speaker's grill is centered.

Anyway, I have another BBC truck, the fan is more centered inside the shroud left and right, but then again it doesn't have the original shroud and can't speak for the alignment.

72c20customcamper · 06-12-2021, 10:53 AM

Put a rebuilt carb on the 68. Ran much better but also found the PCV was defective .Runs great now

ChevyGuyNC · 06-09-2021, 03:21 PM

Washed, Clay bar, compound, polished.

Damn, she looks good! I love this truck!

**Rich72C10** · 06-09-2021, 03:24 PM

Jealous, I'd love to have that color and yours being "Super" - it's the only one that I like (love) better than mine.

What's that other badge on your cow! Makes me wonder, what am I missing LOL

ChevyGuyNC · 06-09-2021, 03:28 PM

Quote:

Originally Posted by Rich72C10

Jealous, I'd love to have that color and yours being "Super" - it's the only one that I like (love) better than mine.

What's that other badge on your cowl? Makes me wonder, what am I missing LOL

It's a dealer sticker, on both sides.

Allen Cook Chevrolet Buick. They went out of business in the late 80's. Found out they did ambulance conversions for a few years in the 60's.

v8truckin · 06-09-2021, 04:24 PM

C-Notch, 2” blocks, POL brake conversion, 2.5” drop spindles, tie rod & ball joint replacement. Just a 2 day project this past wknd…boy was it a butt kicker!

**Rich72C10** · 06-09-2021, 04:29 PM

Low Rider by War comes to mind right about now....

@ChevyGuyNC - now I see why we only get the driver side photos after your wash LOL! Glad Manes and my posting helped you out, that gal is a real nice lady for sure!

ChevyGuyNC · 06-09-2021, 04:37 PM

Quote:

Originally Posted by Rich72C10

@ChevyGuyNC - now I see why we only get the driver side photos after your wash LOL! Glad Manes and my posting helped you out, that gal is a real nice lady for sure!

LOL! That wasn't intentional, I swear... Yes, she sure was nice and I know I'll have my mirror in a few days rather than waiting for the 'big box' guys to ship... Told her y'all recommended me.

KQQL IT · 06-12-2021, 05:37 PM

Rear bushing and seal in the 700r4- still leaks. :/
New 1350 rear u joint.

west9378 · 06-13-2021, 06:00 PM

I must be the world's Greatest Grinder because my welding well it might be a little lacking.

I am trying to weld a cab dolly and I make one pass with the welder and one or two with the grinder. Maybe that is how it is supposed to be done.

I am using a old stick machine I hear mig is easier maybe I should try mig.

body bolt · 06-13-2021, 06:28 PM

Got out there before it heated up and changed the alternator. It had been shutting off at low rpm and required a higher speed than normal to turn on again. Fixed.

**Ol Blue K20** · 06-13-2021, 06:48 PM

Quote:

Originally Posted by west9378

I must be the world's Greatest Grinder because my welding well it might be a little lacking.

I am trying to weld a cab dolly and I make one pass with the welder and one or two with the grinder. Maybe that is how it is supposed to be done.

I am using a old stick machine I hear mig is easier maybe I should try mig.

Turn the heat down a bit and move a bit faster. Otherwise not bad for a stick on thin 2all tubing.

**Grumpy old man** · 06-13-2021, 08:02 PM

Dash repair done . A/C vents cut in , firewall shaved and smoothed , getting closer to paint .

**Ol Blue K20** · 06-13-2021, 09:42 PM

Quote:

Originally Posted by Grumpy old man

Dash repair done . A/C vents cut in , firewall shaved and smoothed , getting closer to paint .

Looking good Grumpy!

**71CHEVYSHORTBED402** · 06-14-2021, 02:49 AM

Quote:

Originally Posted by Grumpy old man

Dash repair done . A/C vents cut in , firewall shaved and smoothed , getting closer to paint .

Nice Grumps

06-03-2021, 06:08 PM	#1
Accelo Registered User Join Date: Mar 2015 Location: washington Posts: 2,178	Re: What did you do to your truck today.The 3rd chapter In my prior life I have installed compression fittings on a 10,000 psi system.

06-03-2021, 11:50 PM	#2
cab4word67 Registered User Join Date: Sep 2020 Location: portland oregon Posts: 183	Re: What did you do to your truck today.The 3rd chapter Got the truck on the hoist today, box going on tomarrow, new 6" drop is installed and the flip kit/C notch has been done. Now I need to remanufacture the tilt hinges and reinstall the drivetrain. Would like to be done by end of month Last edited by cab4word67; 06-03-2021 at 11:55 PM. Reason: loading pic

06-04-2021, 08:21 AM	#3
67C10Step Registered User Join Date: Jul 2019 Location: Beebe, AR Posts: 2,436	Re: What did you do to your truck today.The 3rd chapter cab, Wow! Interesting. Did you take the 4x4 in your avatar and make it 2wd? Love the blue. __________________ 1967 C10 1980 Jeep CJ5 2020 Toyota 4Runner 2020 Toyota CH-R 2020 Acura MDX

06-05-2021, 03:29 AM	#4
Already Gone 70+ ( Old Skool Club ) Join Date: Nov 2003 Location: Saskatoon, Saskatchewan ,Canada Posts: 9,078	Re: What did you do to your truck today.The 3rd chapter Had my 255/60 17 inch Bridgestones delivered, Fed Ex contractor left like this, that will be going on my truck probably next year. Now to save for the Torque Thrusts. Attached Images __________________ 1972 C10 Custom/Deluxe 613 Highlander 406/700R4 1999 White Tahoe LS 4x2 with Z56 Police Package 1992 K1500 GMC Suburban Members I have personally met: MusicMan70 - HeavyD - ChewyChevy67 - StingRay -71SWB4x4 - 67 Burb - DeadheadNM - too much stuff - bc65 - das601 " Circumsatances Do Not Change Responsibility " " The Sky is not the Limit, Your Mind is." Marilyn Monroe .. RIP Charlie Watts 1941 - 2021

06-06-2021, 07:40 PM	#5
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,210	Re: What did you do to your truck today.The 3rd chapter 72 died on me today in the driveway. Starter must have a dead short tried jumping the solenoid with the tester starter button . Nothing and the button got hot quick. So I have a new one on the way as it was under warranty but I’m done with DBElectric . 3 in two years on 2 different vehicles. So I ordered a Powermaster mini . I also tried one of the M/T wheels that came off the Tacoma on the 68 . Pain in the butt sanding them to this finish by hand ,may just sand with 400 and paint them black . Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

06-06-2021, 08:43 PM	#7
pjmoreland Senior Member Join Date: Jan 2005 Location: CA Posts: 5,342	Re: What did you do to your truck today.The 3rd chapter I completed several small projects today, some of which have been on my to-do list for a long time: Replaced the output seal on my recently rebuilt 700R4. Either I damaged it or it was defective. Went with a GM seal this time. Made a mirror image tailpipe hanger bracket for a full length exhaust system I'm planning on getting. Also installed stock hangers on both sides of the chassis in the middle of the truck Installed a replacement hood hinge I painted yesterday. The original Hinge was bent sideways enough that the open limit stop no longer worked. Painted and installed a set of shorty 5/16 body screws in the left inner fender brace. These screws are hard to find. Attached Images

06-09-2021, 03:00 PM	#8
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Got tint and clear windshield over with tint visor! Now I’m all set for the Texas sun and my trip up to East Texas! Attached Images __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| Upgraded Fully Super Trim Last edited by Rich72C10; 06-09-2021 at 03:22 PM.*

06-10-2021, 03:20 PM	#9
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Made my 300 drive to Kilgore! Truck ran like a dream, 13.5 mpg going 65 ~ 75 and through tons of little towns on US hwy 79! Also daughter had a good nap - kids can sleep anywhere ;-) Attached Images __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

06-10-2021, 04:48 PM	#10
70cst Senior Member Join Date: Feb 2001 Location: New Madison, Ohio Posts: 21,349	Re: What did you do to your truck today.The 3rd chapter My refurbished CB came in today ... Attached Images __________________ A husband can be right...or...A husband can be happy. 67-72 Chevy and GMC Trucks...The Classic Truck for the Classic Folk. 1970 CST Two tone green, 402BB, 400 Automatic, Tach, Buckets, AC, AM-FM, Tilt, GM CB, GM 8 Tract, LWB, etc JOHN 17:3...The better side of "LIFE" Remember: Everyday is a good day...Some are just gooder!

06-12-2021, 10:53 AM	#12
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,210	Re: What did you do to your truck today.The 3rd chapter Put a rebuilt carb on the 68. Ran much better but also found the PCV was defective .Runs great now __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

06-09-2021, 03:21 PM	#13
ChevyGuyNC Registered User Join Date: Sep 2011 Location: Jacksonville, FL Posts: 143	Re: What did you do to your truck today.The 3rd chapter Washed, Clay bar, compound, polished. Damn, she looks good! I love this truck! __________________ 1972 Cheyenne Super LWB, 350V8, AC, PS, PB, all original 46k survivor

06-09-2021, 03:24 PM	#14
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Jealous, I'd love to have that color and yours being "Super" - it's the only one that I like (love) better than mine. What's that other badge on your cow! Makes me wonder, what am I missing LOL __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

06-09-2021, 04:24 PM	#16
v8truckin Registered User Join Date: Oct 2020 Location: California Posts: 21	Re: What did you do to your truck today.The 3rd chapter C-Notch, 2” blocks, POL brake conversion, 2.5” drop spindles, tie rod & ball joint replacement. Just a 2 day project this past wknd…boy was it a butt kicker! Attached Images

06-09-2021, 04:29 PM	#17
Rich72C10 Mr. Cheyenne Join Date: Jun 2020 Location: Kyle, Texas Posts: 1,644	Re: What did you do to your truck today.The 3rd chapter Low Rider by War comes to mind right about now.... @ChevyGuyNC - now I see why we only get the driver side photos after your wash LOL! Glad Manes and my posting helped you out, that gal is a real nice lady for sure! __________________ Richard *'72 Chevy C10 Cheyenne Super WHT/MED BRONZE/WHT SBC 350 \| TH350 \| LWB \| AC \| Buddy Seats Upgrades:** Tilt \| Front Sway Bar \| Radio \| Sliding Window \| Bed Spare w/Lock Bed Rails \| Full LEDs \| Courtesy Lights \| Tachometer \| Glovebox Lock & Light \| Head Light Relays \| *Upgraded Fully Super Trim

06-12-2021, 05:37 PM	#19
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,158	Re: What did you do to your truck today.The 3rd chapter Rear bushing and seal in the 700r4- still leaks. :/ New 1350 rear u joint. __________________ " That didnt make it any newer " " Dont antique the equipment "



Register or Log In To remove these advertisements.

06-13-2021, 06:00 PM	#20
west9378 Registered User Join Date: Dec 2009 Location: Pulaski, TN Posts: 114	Re: What did you do to your truck today.The 3rd chapter I must be the world's Greatest Grinder because my welding well it might be a little lacking. I am trying to weld a cab dolly and I make one pass with the welder and one or two with the grinder. Maybe that is how it is supposed to be done. I am using a old stick machine I hear mig is easier maybe I should try mig. Attached Images __________________ West My Project and Photo Album http://67-72chevytrucks.com/vboard/s...d.php?t=378159 http://67-72chevytrucks.com/vboard/a...hp?albumid=641

06-13-2021, 06:28 PM	#21
body bolt Registered User Join Date: Oct 2020 Location: Albuquerque, New Mexico Posts: 475	Re: What did you do to your truck today.The 3rd chapter Got out there before it heated up and changed the alternator. It had been shutting off at low rpm and required a higher speed than normal to turn on again. Fixed.

06-13-2021, 08:02 PM	#23
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: What did you do to your truck today.The 3rd chapter Dash repair done . A/C vents cut in , firewall shaved and smoothed , getting closer to paint . Attached Images __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop

Register or Log In To remove these advertisements.