What did you do to your truck today? Chapter II - Page 80 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

66pnl · 04-02-2015, 02:36 AM

Took more than a day but had my inner wheel wells blasted. Then prepped, dp 90 and underhood black. I have to drive my junk every day, so one project at a time.

7tee · 04-02-2015, 06:31 AM

Quote:

Originally Posted by 66pnl

Took more than a day but had my inner wheel wells blasted. Then prepped, dp 90 and underhood black. I have to drive my junk every day, so one project at a time.

Nice job and looks great. A friend of mine has some chrome ones for sale but that's not for me...

Econman · 04-02-2015, 06:31 AM

Got my drive line installed and ordered new belts, hoses and p/s lines.

Name: 0401151536.jpg
Views: 873
Size: 40.7 KB

texasld · 04-02-2015, 12:38 PM

Got my exhaust finished up!

Name: Exhaust.jpg
Views: 851
Size: 84.2 KB

ole dollor · 04-02-2015, 10:03 PM

Quote:

Originally Posted by texasld

Got my exhaust finished up!

Attachment 1385815

dang that looks good....that is some fine work.

Possmguts · 04-02-2015, 10:13 PM

Quote:

Originally Posted by Econman

Got my drive line installed and ordered new belts, hoses and p/s lines.

Attachment 1385771

Nice.. I should be at this point next week. Building the rear end this weekend

Possmguts · 04-02-2015, 10:15 PM

Quote:

Originally Posted by texasld

Got my exhaust finished up!

Attachment 1385815

super clean looking... I had to do away with the turn downs because of the dust they kick up though. Ill do a side dump in front of the rear tires with a 6 inch oval tip

texasld · 04-03-2015, 01:56 PM

Quote:

Originally Posted by ole dollor

dang that looks good....that is some fine work.

Thanks, man! I used the Flowmaster u-fit kit and hacked up about every piece to make it the way I wanted. Then ground down all of the welds to make it "seamless" Don't know if I'll do it again because of all the time involved doing it the way I did it.

Quote:

Originally Posted by Possmguts

super clean looking... I had to do away with the turn downs because of the dust they kick up though. Ill do a side dump in front of the rear tires with a 6 inch oval tip

Thanks man, I hear about that. Hopefully I'll keep it off of really dusty roads and parking lots.

74baggedbug · 04-03-2015, 02:37 PM

Modified the billet shifter to work in our non-tilt columns

Gravityamp · 04-03-2015, 06:20 PM

Quote:

Originally Posted by 74baggedbug

Modified the billet shifter to work in our non-tilt columns

looks xlint

Gravityamp · 04-03-2015, 06:28 PM

More polishing on the paint and better yet , I finally did the headlight relays ! Omg! Huge difference I'm talking night and day or day and night or maybe it's turned my nights into days ! Unbelievable how much of a difference this makes . I will post pics of the headlights after dark lol

Thank you everyone on the site for all the help

Peace all and Happy Easter

sixty-eight shorty · 04-03-2015, 09:43 PM

Quote:

Originally Posted by 74baggedbug

Modified the billet shifter to work in our non-tilt columns

74baggedbug , you gauge panel , steering wheel and shifter look great .
I am about to buy the same shifter and was thinking it was a direct bolt on
Can you tell what did you have to do to the shifter to make it work ?
Thank you , Frank

74baggedbug · 04-03-2015, 10:11 PM

Quote:

Originally Posted by sixty-eight shorty

74baggedbug , you gauge panel , steering wheel and shifter look great .
I am about to buy the same shifter and was thinking it was a direct bolt on
Can you tell what did you have to do to the shifter to make it work ?
Thank you , Frank

I had to have the part of the stock shifter that goes I to the column machined down to fit into the billet shifter.. The piece that comes with the billet shifter is to short and won't work on our non-tilt columns

bgwss · 04-04-2015, 09:02 AM

Quote:

Originally Posted by Gravityamp

I finally did the headlight relays ! Omg! Huge difference I'm talking night and day or day and night or maybe it's turned my nights into days ! U

Did you use a kit for the headlight relays? Where did you get it from?

70 shop truck · 04-04-2015, 02:52 PM

Drained remaining fuel from my tank in prep for tank/lines replacement next week. Rebuilt Edelbrock carb and man was it dirty with all of the rust and junk in the tank. PO told me it was a 600 CFM but once I removed it I found out it's a 750 CFM. Bit overkill for a stock 350 and I will have to look to change that out in the future.

Possmguts · 04-04-2015, 06:07 PM

Learned when assembling my rear end that something is wrong... wrong part somewhere. Summit Tech Line is closed.

Eaton posi carrier is making contact with the pinion gear before the carrier bearings are even in the seats... So progress for the weekend is dead in the water.... On to the Rum and Coke....

Saclandman · 04-04-2015, 11:13 PM

https://youtu.be/4iIFMcI5GW8

Fired it up for the first time since the engine swap. F$@k yeah!

colgad · 04-04-2015, 11:33 PM

Quote:

Originally Posted by Saclandman

https://youtu.be/4iIFMcI5GW8

Fired it up for the first time since the engine swap. F$@k yeah!

You made the video private. No one can see/hear it

Possmguts · 04-05-2015, 09:19 AM

Quote:

Originally Posted by Possmguts

Learned when assembling my rear end that something is wrong... wrong part somewhere. Summit Tech Line is closed.

Eaton posi carrier is making contact with the pinion gear before the carrier bearings are even in the seats... So progress for the weekend is dead in the water.... On to the Rum and Coke....

Well... I guess I bought 3 series gears and a 4 series carrier.... SMH....

Saclandman · 04-05-2015, 11:26 AM

Quote:

Originally Posted by colgad

You made the video private. No one can see/hear it

Well, crap. How about this one?

https://youtu.be/Hy8CGih1rMs

magwakeenercew2jh · 04-05-2015, 12:04 PM

Quote:

Originally Posted by Saclandman

Well, crap.

Easy to fix:

Go to:

YouTube>

Click: "My Channel" (left side of the page)>"Video Manager"(top of the page)>

Find the video you put up and there's a box next to it (on the left), Check it with a click.

Then Click:

"Edit">"Private">"Public">"Save Changes" (bottom right of the page).

Done.

magwakeenercew2jh · 04-05-2015, 12:06 PM

Quote:

Originally Posted by Saclandman

Well, crap. How about this one?

https://youtu.be/Hy8CGih1rMs

That works. Very Nice.

VWNate1 · 04-05-2015, 01:07 PM

Quote:

Originally Posted by Saclandman

https://youtu.be/4iIFMcI5GW8

Fired it up for the first time since the engine swap. F$@k yeah!

Indeed ! that sounds great .

70 shop truck · 04-05-2015, 02:29 PM

Stripped down my interior and removed the old gas tank. Removed old seat cover and foam and now I'm just sitting around looking for that FedEx truck full of goodies so I can start putting her all back together again. It was pleasant to find that the floor and the seat frame look really good. Frame only needed a light brush and some paint down on the bottom.

cooperhw · 04-05-2015, 04:02 PM

I widened the tailgate 6 inches to match the bed I did earlier this weekend.
It's now a Chevivrolet. I don't know if I will leave it like that or put a patch panel over it with a bow tie or something? We'll see.

04-02-2015, 02:36 AM	#1976
66pnl Registered User Join Date: Mar 2014 Location: Eagle creek or Posts: 108	Re: What did you do to your truck today? Chapter II Took more than a day but had my inner wheel wells blasted. Then prepped, dp 90 and underhood black. I have to drive my junk every day, so one project at a time. Attached Images __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=620707

04-02-2015, 06:31 AM	#1978
Econman Registered User Join Date: Feb 2011 Location: Knoxville, TN Posts: 362	Re: What did you do to your truck today? Chapter II Got my drive line installed and ordered new belts, hoses and p/s lines.

04-02-2015, 12:38 PM	#1979
texasld Registered User Join Date: Dec 2013 Location: Wilmot, NH Posts: 443	Re: What did you do to your truck today? Chapter II Got my exhaust finished up! __________________ 1969 C10 SWB 5.3L LS, 4l60e, 2/4 drop (In Progress) 2015 GMC 2500 Duramax (Daily Driver) 1999 Jeep TJ 2010 Harley Street Glide Check Out My Build!: http://67-72chevytrucks.com/vboard/s...d.php?t=617981

04-03-2015, 02:37 PM	#1984
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 699	Re: What did you do to your truck today? Chapter II Modified the billet shifter to work in our non-tilt columns

04-03-2015, 06:28 PM	#1986
Gravityamp Registered User Join Date: Sep 2014 Location: Fresno Ca. Posts: 74	Re: What did you do to your truck today? Chapter II More polishing on the paint and better yet , I finally did the headlight relays ! Omg! Huge difference I'm talking night and day or day and night or maybe it's turned my nights into days ! Unbelievable how much of a difference this makes . I will post pics of the headlights after dark lol Thank you everyone on the site for all the help Peace all and Happy Easter Attached Images __________________ 69 GMC 400/400 2.5/4 drop from ECE

04-04-2015, 02:52 PM	#1990
70 shop truck Registered User Join Date: Oct 2014 Location: hampstead nc Posts: 78	Re: What did you do to your truck today? Chapter II Drained remaining fuel from my tank in prep for tank/lines replacement next week. Rebuilt Edelbrock carb and man was it dirty with all of the rust and junk in the tank. PO told me it was a 600 CFM but once I removed it I found out it's a 750 CFM. Bit overkill for a stock 350 and I will have to look to change that out in the future. __________________ 1970 Long bed- Stress release "There are only two kinds of people that understand Marines: Marines and those who have met them in battle. Everyone else has a second-hand opinion." Unknown

04-04-2015, 06:07 PM	#1991
Possmguts Registered User Join Date: Nov 2014 Location: Columbiana Ohio Posts: 1,210	Re: What did you do to your truck today? Chapter II Learned when assembling my rear end that something is wrong... wrong part somewhere. Summit Tech Line is closed. Eaton posi carrier is making contact with the pinion gear before the carrier bearings are even in the seats... So progress for the weekend is dead in the water.... On to the Rum and Coke.... __________________ "Hey... its only time and money right? Just do it." 67 Short Bed under major construction http://67-72chevytrucks.com/vboard/s...=651356&page=8

04-04-2015, 11:13 PM	#1992
Saclandman Registered User Join Date: May 2013 Location: Sacramento, CA Posts: 487	Re: What did you do to your truck today? Chapter II https://youtu.be/4iIFMcI5GW8 Fired it up for the first time since the engine swap. F$@k yeah! __________________ Rich J. 1967 Chevy C20 Longbed Stepside w/283 and 4spdSOLD 2002 Chevy Tahoe 4X4 5.3L SOLD 2015 Chevy Silverado Crew 4X4 5.3L

04-05-2015, 02:29 PM	#1999
70 shop truck Registered User Join Date: Oct 2014 Location: hampstead nc Posts: 78	Re: What did you do to your truck today? Chapter II Stripped down my interior and removed the old gas tank. Removed old seat cover and foam and now I'm just sitting around looking for that FedEx truck full of goodies so I can start putting her all back together again. It was pleasant to find that the floor and the seat frame look really good. Frame only needed a light brush and some paint down on the bottom. __________________ 1970 Long bed- Stress release "There are only two kinds of people that understand Marines: Marines and those who have met them in battle. Everyone else has a second-hand opinion." Unknown

04-05-2015, 04:02 PM	#2000
cooperhw Registered User Join Date: Oct 2014 Location: Mesa AZ (Near Phoenix) Posts: 2,302	Re: What did you do to your truck today? Chapter II I widened the tailgate 6 inches to match the bed I did earlier this weekend. It's now a Chevivrolet. I don't know if I will leave it like that or put a patch panel over it with a bow tie or something? We'll see. Attached Images __________________ "Life is too short to drive a boring vehicle". Later, Wayne



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.