Show your motor... - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**americanmusc1e** · 01-05-2010, 12:46 PM

Quote:

Originally Posted by mosesburb

just a big heavy six cylinder. Turbo'd, intercooled, and fuel injected. Runs on diesel too.

i want one!!!!!!

tapeworm · 01-06-2010, 01:21 AM

Quote:

Originally Posted by mosesburb

Just a big heavy six cylinder. Turbo'd, intercooled, and fuel injected. Runs on diesel too.

A 6BT in a 72 Burb; I have now seen it all

Anyone like seeing diesel engines in anything check out this site

www.4btswaps.com/

howard_m18 · 01-06-2010, 02:10 AM

I thought I posted mine,BUT can't find it? My mind is my best friend, I just wish it would visit me more often!! The stock 350 came out of a 68 conversion van that I had & it is hooked up to a 700 trans!

s_nova69 · 01-06-2010, 02:13 AM

Here is my 500 hp 406. 5.7 gm pm rods, stock crank, Chapman ported Sportsman II heads, stainless rockers, gmpp alum water pump, fully balanced. Is installed in my 70 Longhorn now. Runs hard.

c10seconds · 01-06-2010, 03:44 AM

Quote:

Originally Posted by rob32472

Here's mine

what headers and motormount adapter did you use? are you happy with the clearance? Im in the process of converting my 67 2wd to an lsx. trying to figure out the best way to do it.

**Hart_Rod** · 01-06-2010, 10:56 AM

Quote:

Originally Posted by c10seconds

what headers and motormount adapter did you use? are you happy with the clearance? Im in the process of converting my 67 2wd to an lsx. trying to figure out the best way to do it.

They are Doug Thorley Headers and Early Classic Enterprises (ECE) motor mounts. It's the same setup I have on both of my trucks. Clearances are great and both products work as advertised.

**425HP409** · 01-07-2010, 04:45 PM

Here is the engine I have finished for my 68. It is a Gen 5 454 with original 402 heads, intake & exhaust manifolds, and accessory brackets. I installed a Holley Spreadbore that I rebuilt and I test ran it and made all adjustments on my engine stand, and now am ready to install it in the truck.

chevy_mike · 01-10-2010, 11:46 PM

Finally got my engine done to the point of needing to install back in the frame.

Went from this,

To this,

po_bird · 01-16-2010, 11:41 PM

Yeah! Keep em coming

'72customdeluxe · 01-16-2010, 11:50 PM

Quote:

Originally Posted by s_nova69

Here is my 500 hp 406. 5.7 gm pm rods, stock crank, Chapman ported Sportsman II heads, stainless rockers, gmpp alum water pump, fully balanced. Is installed in my 70 Longhorn now. Runs hard.

lol srsly? And if it's cranking out 500 why are you running flowtechs with 1.5" primaries. Need more like 1-7/8

AJs72K5 · 01-17-2010, 01:15 AM

BBC 460. Edelbrock aluminum heads. Edelbrock MPFI. Comp hydraulic roller cam. 10:1 compression. Camquest says: 515hp @ 5000; 580tq @ 4000. Going in my 72 K5.

420am · 01-17-2010, 05:34 AM

Work in progress..

350 cid
Edelbrock 650cfm
Edeldrock 1" carb spacer
Edelbrock EPS Manifold
Lunati Bracket Master II Cam / Lifters / Pushrods
Comp Cams Roller Rockers
Comp Cams Double Roller
'906' Iron Vortec Heads

Not pictured..
MSD Distributor Cap/Rotor
MSD Streetfire Wires

I've done about everything I can without pulling the motor. I know if I pull it out I'll tear it completely down and I won't have the money to put it together before summer. This motor was just a O'Reilly's rebuilt motor with maybe 20k on it that I was going to replace a head gasket on.. then replace a head gasket and port and polish the old crap '882' heads on.. then I got new heads, which required a new intake.. Hahaha.. I wonder when I'll be done.

**FRENCHBLUE72** · 01-17-2010, 01:06 PM

Heres the 454 in my 72 sounds good still have not even drove the damn thing...

YouTube- 454 running

OldSkool71 · 01-17-2010, 09:26 PM

Quote:

Originally Posted by Old Red

Here's a 427 with 3 two's

I want that!!!

nuke1 · 01-18-2010, 12:12 AM

Here's mine, i love showing it off, but next winter she will be apart agaoin.

po_bird · 01-18-2010, 12:14 AM

Green is mt fav color

ozman3803 · 01-18-2010, 12:39 AM

Sweet thread, I love SBC but how about some 500+ci BBC

Inked Okie · 01-18-2010, 01:30 PM

68 chevy 350 still under construction

dznucks · 01-18-2010, 02:28 PM

68stepbed, bigsnookmaster,

What engine paint are you two using? those two motors look awsome.

*Fitz* · 01-18-2010, 02:42 PM

572/620 in my 67 Stepside:

kvn1011 · 01-18-2010, 04:34 PM

Quote:

Originally Posted by Fitz

572/620 in my 67 Stepside:

nice!!!

68Stepbed · 01-18-2010, 06:37 PM

dznucks, I used rattle can touchup paint(MOPAR to match truck color) for my block and heads. The VC's, intake and other bits and pieces, I used DupliColor Cast Coat Iron engine enamel from Advanced Auto Parts.

po_bird · 01-18-2010, 10:22 PM

Fitz thats one bad azz motor

dznucks · 01-20-2010, 09:18 AM

Thanks 68stepbed

Fastest32 · 01-23-2010, 09:44 PM

..

01-06-2010, 02:10 AM	#78
howard_m18 Registered User Join Date: Mar 2009 Location: clarkston,MI Posts: 217	Re: Show your motor... I thought I posted mine,BUT can't find it? My mind is my best friend, I just wish it would visit me more often!! The stock 350 came out of a 68 conversion van that I had & it is hooked up to a 700 trans! Attached Images __________________ 1967 C10 LWB, painted 2010 MUSTANG GRABBER BLUE & finally got it on the road after sitting in garage for 10+ yrs. Howard in MI.

01-06-2010, 02:13 AM	#79
s_nova69 Registered User Join Date: Jul 2007 Location: slc, ut Posts: 318	Re: Show your motor... Here is my 500 hp 406. 5.7 gm pm rods, stock crank, Chapman ported Sportsman II heads, stainless rockers, gmpp alum water pump, fully balanced. Is installed in my 70 Longhorn now. Runs hard. Attached Images __________________ Phil '70 Longhorn 421 700r4 tach 4 wheel disc hydroboost daily driver '72 short super build 4wd '72 Suburban LT4 coming soon!!

01-07-2010, 04:45 PM	#82
425HP409 425hp409 Join Date: Oct 2008 Location: Prosper Texas Posts: 834	Re: Show your motor... Here is the engine I have finished for my 68. It is a Gen 5 454 with original 402 heads, intake & exhaust manifolds, and accessory brackets. I installed a Holley Spreadbore that I rebuilt and I test ran it and made all adjustments on my engine stand, and now am ready to install it in the truck. Attached Images __________________ Charles 68 SWB, Dad bought new, now 396 & factory ac 64 Impala SS, 409 425HP, 4 speed AC 64 Bel Air Wagon, 400 Small Block 57 Bel Air all original 283 w/Factory Air 77 GMC Sprint, 454/425HP 67 Olds 442, all original 90 ZR1 Corvette

01-10-2010, 11:46 PM	#83
chevy_mike Never Ending Projects Join Date: Jul 2006 Location: San Diego, CA Posts: 3,836	Re: Show your motor... Finally got my engine done to the point of needing to install back in the frame. Went from this, To this, __________________ . 1965 C10 Panel, Tiki Express http://www.67-72chevytrucks.com/vboa...d.php?t=506580 SOLD 1968 Chevy C10, Long, Fleetside, Hot Rod Hauler http://67-72chevytrucks.com/vboard/s...d.php?t=313233 SOLD 1965 Chevy C10, Long, Fleetside, Hot Rod C10 http://67-72chevytrucks.com/vboard/s...d.php?t=415702 SOLD We were given two ears and one mouth for a reason... listen twice as much and speak half as often... Last edited by chevy_mike; 01-10-2010 at 11:47 PM.

01-16-2010, 11:41 PM	#84
po_bird Registered User Join Date: Oct 2005 Location: MUSKOGEE, OK Posts: 229	Re: Show your motor... Yeah! Keep em coming __________________ 72 SIERRA LB 74 C10 SB 85 C10 SB 75 EL CAMINO SS

01-17-2010, 01:15 AM	#86
AJs72K5 Registered User Join Date: Nov 2007 Location: South Tx Posts: 1,083	Re: Show your motor... BBC 460. Edelbrock aluminum heads. Edelbrock MPFI. Comp hydraulic roller cam. 10:1 compression. Camquest says: 515hp @ 5000; 580tq @ 4000. Going in my 72 K5. __________________ - AJ Gray Matter Build - 1972 K5 with some stuff

01-17-2010, 05:34 AM	#87
420am Registered User Join Date: Feb 2008 Location: Madison, WI Posts: 357	Re: Show your motor... Work in progress.. 350 cid Edelbrock 650cfm Edeldrock 1" carb spacer Edelbrock EPS Manifold Lunati Bracket Master II Cam / Lifters / Pushrods Comp Cams Roller Rockers Comp Cams Double Roller '906' Iron Vortec Heads Not pictured.. MSD Distributor Cap/Rotor MSD Streetfire Wires I've done about everything I can without pulling the motor. I know if I pull it out I'll tear it completely down and I won't have the money to put it together before summer. This motor was just a O'Reilly's rebuilt motor with maybe 20k on it that I was going to replace a head gasket on.. then replace a head gasket and port and polish the old crap '882' heads on.. then I got new heads, which required a new intake.. Hahaha.. I wonder when I'll be done. __________________ 1972 Long Bed Cheyenne Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=285282 Waste my bandwidth and listen to some great tunes >> http://www.radioxenu.com (Live Shows with yours truly every Friday) Last edited by 420am; 01-17-2010 at 05:37 AM.

01-18-2010, 12:12 AM	#90
nuke1 Registered User Join Date: Jun 2007 Location: Saskatoon, Saskatchewan,: Posts: 2,901	Re: Show your motor... Here's mine, i love showing it off, but next winter she will be apart agaoin. Attached Images __________________ James 1968 GMC "HAVOC" 1986 GMC "Frank" J.J.R.H. Design & Consulting My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300 A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238 1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361 Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390 Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100 1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587

01-18-2010, 12:14 AM	#91
po_bird Registered User Join Date: Oct 2005 Location: MUSKOGEE, OK Posts: 229	Re: Show your motor... Green is mt fav color __________________ 72 SIERRA LB 74 C10 SB 85 C10 SB 75 EL CAMINO SS

01-18-2010, 12:39 AM	#92
ozman3803 Registered User Join Date: Jun 2009 Location: Lincoln, NE Posts: 125	Re: Show your motor... Sweet thread, I love SBC but how about some 500+ci BBC

01-18-2010, 01:30 PM	#93
Inked Okie Registered User Join Date: Feb 2009 Location: Tulsa, Oklahoma Posts: 25	Re: Show your motor... 68 chevy 350 still under construction Attached Images __________________ Wade

01-18-2010, 02:28 PM	#94
dznucks Registered User Join Date: Feb 2006 Location: Smyrna, Ga Posts: 1,647	Re: Show your motor... 68stepbed, bigsnookmaster, What engine paint are you two using? those two motors look awsome. Last edited by dznucks; 01-18-2010 at 02:28 PM.

01-18-2010, 02:42 PM	#95
Fitz Account Suspended Join Date: Jan 2007 Location: Tucson Posts: 2,183	Re: Show your motor... 572/620 in my 67 Stepside: Attached Images

01-18-2010, 06:37 PM	#97
68Stepbed Registered User Join Date: Mar 2005 Location: 10-Uh-See Posts: 5,609	Re: Show your motor... dznucks, I used rattle can touchup paint(MOPAR to match truck color) for my block and heads. The VC's, intake and other bits and pieces, I used DupliColor Cast Coat Iron engine enamel from Advanced Auto Parts. __________________ Matt 68 C10 stepside, LS1/700R4, TCI Engineering suspension system

01-18-2010, 10:22 PM	#98
po_bird Registered User Join Date: Oct 2005 Location: MUSKOGEE, OK Posts: 229	Re: Show your motor... Fitz thats one bad azz motor __________________ 72 SIERRA LB 74 C10 SB 85 C10 SB 75 EL CAMINO SS



Register or Log In To remove these advertisements.

01-20-2010, 09:18 AM	#99
dznucks Registered User Join Date: Feb 2006 Location: Smyrna, Ga Posts: 1,647	Re: Show your motor... Thanks 68stepbed

01-23-2010, 09:44 PM	#100
Fastest32 Registered User Join Date: Nov 2009 Location: Austin Texas Posts: 370	Re: Show your motor... .. Last edited by Fastest32; 01-23-2010 at 09:49 PM. Reason: Wrong section

Register or Log In To remove these advertisements.