Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
07-29-2015, 09:28 AM | #1 |
Registered User
Join Date: Oct 2012
Location: Miami, Florida
Posts: 910
|
electrical needs of mty c10
hello to all. I have a 1971 c10, stout, fuel injected 370 lq9/th400 with air ride suspension, 2 Viair air compressors, walbro electric fuel pump, custom dash with autometer gauges, and dual electric fans. I plan to add AC in the near future. I want to address my electrical needs. lets say, hypothecally that I want to power all this at the same time. how can I ensure the each unit is getting all the power, it needs. my first step is to upgrade the alternator and battery, right? powermaster 255 and a yellow top optima battery? what some your tricks?
|
07-29-2015, 12:22 PM | #2 | |
Old member
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
|
Re: electrical needs of mty c10
Quote:
Anything requiring large amp draw put on relays.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver Seeing the USA in a 71 Upstate SC GM Truck Club 2013,14 and 2016 Hot Rod Pour Tour http://upstategmtrucks.com/ Get out and drive the truck this summer and have some fun! It sucks not being able to hear! LWB trucks rule, if you don't think so measure your SWB! After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs. |
|
07-30-2015, 08:27 AM | #3 |
1965 Chevy C10, 2005 4.8L/4l60
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,539
|
Re: electrical needs of mty c10
Stock AC compressor or aftermarket?
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 support our troops! |
07-30-2015, 08:51 AM | #4 |
Registered User
Join Date: Oct 2012
Location: Miami, Florida
Posts: 910
|
Re: electrical needs of mty c10
sanden possibly. I have relays on every thing such as fans, viair compressors, ignition, fuel pump. at night, when the lights are are on the seem dim. I expect them to be brighter. what battery would a good power source to tar with? nice truck Clyde65. 4.8/4l60E, good, proven drivetrain.
Last edited by dec010974; 07-30-2015 at 08:52 AM. Reason: grammar |
07-31-2015, 09:59 AM | #5 |
Registered User
Join Date: Apr 2011
Location: Klein Texas
Posts: 3,852
|
Re: electrical needs of mty c10
The fans are the big power hogs. You could be pulling near 50 amps when their on.
I'd have the headlights on a relay also.
__________________
My Classics: '72 K20 Suburban + '65 Dodge Town Wagon '72 Corvette Roadster +'67 Corvette Roadster '73 Z-28 Camaro '63 Ford SWB Uni Pickup '50 Ford Coupe |
08-01-2015, 06:53 AM | #6 |
Registered User
Join Date: Oct 2012
Location: Miami, Florida
Posts: 910
|
Re: electrical needs of mty c10
interesting. put the light on a relay. if you don't mind explaining, how will this helps?
|
08-01-2015, 10:44 AM | #7 |
Msgt USAF Ret
Join Date: Jan 2005
Location: Kalamazoo, Michigan
Posts: 8,703
|
Re: electrical needs of mty c10
The wiring on these older trucks is a fairly small gauge and as they get older they develop more resistance to current flow. In addition to that the switches become overheated from carrying the current and they gradually burn out.
Headlight, heater, ignition and dimmer for instance. What the relays do is carry the high current loads in the truck circuit. The vehicle switches then just turn on the relays instead of the loads directly. It takes just a few milliamps to turn on a relay as opposed to turning on a fan or a light. The voltage required to do that is much much less than what is required to operate the headlights or the heater motor. The result is a much smaller voltage drop in the circuit and more power for the lights and the fan. This means brighter lights, more current for the fan motor and anything else on a relay circuit. The headlights are operated by a main power wire going to the headlight switch, 12 gauge red and a 12 gauge blue wire from there to the dimmer switch. From the dimmer switch we have 2 smaller wires, Tan ( low beam ),and green, (high beam ) that run directly to the headlights to the left and then over to the right. These small wires carry the full current load to the headlights and the voltage drop over all that resistance can be as high as 2 volts. So you have 10 volts for the headlights instead of 12. Here's what we do to cure the problem. We run 12 volts through the relays for the light power over a much shorter distance result brighter lights and less dimming at engine idle. Notice the 12 volt power to the relays to terminals 30 and the exit power to the headlights from terminals 87. The terminal 30 wire is fused by a 20 amp fuse, for each headlight. The relay coils then become the controls for turning on the lights. We run the tan wire to the no. 86 terminal and then ground the 85 terminal to a good solid ground. Now we have the low beam circuit completed. We do the same to the light green wire on the other relay for the high beams and marvel at the brighter lights. The wires in the diagram are different colors but than stock but we can substitute the correct colors using the tan and green and of course black for ground. Be sure to clean and tighten the headlight connections and the grounds. For you GM guys we have a slightly different diagram.
__________________
VetteVet metallic green 67 stepside 74 corvette convertible 1965 Harley sportster 1995 Harley wide glide Growing old is hell, but it beats the alternative. Last edited by VetteVet; 08-01-2015 at 10:52 AM. |
08-01-2015, 02:32 PM | #8 |
meowMEOWmeowMEOW
Join Date: Sep 2009
Location: MKE WI
Posts: 7,128
|
Re: electrical needs of mty c10
Mine has been fully rewired, but I echo the sentiments above. Making sure you have a good thick gauge wire for power feeds or anything that has a high constant draw, can really make a difference. The old solid core stuff can easily be overpowered and melt down.
__________________
'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING MY BUILD THE H8RDCPTR //\\ MY YOUTUBE CHANNEL REV J HD
|
08-03-2015, 11:09 PM | #9 |
Registered User
Join Date: Oct 2012
Location: Miami, Florida
Posts: 910
|
Re: electrical needs of my c10
well br3w and vettevet, I fully understand. my electrical was rewired. well I just thought that since I rewired my entire truck with a new electrical fuse box that the wiring should be up to par. I even thought about using the new leds which I know run on a relay system. thanks for the info. this will be my next assignment on the truck. this shouldn't interfere with my t56 funds.
|
Bookmarks |
|
|