The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-17-2003, 12:21 AM   #1
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
INSTALL: Tennman's Sidemarker Fuel Fill on a Stepside

Finally got around to showing the install! I hope this helps everyone. There are alot of pics, so it might take awhile to load them all.

Here is what I used:

1- 1997 S10 fuel filler door with neck
1- 1 1/2 fuel filler hose (see blazer tank install for part number)
3 ft of 5/8" hose
4- 1/4" machine threaded bolts 1 1/4" long
4- nylon lock nuts for above bolts
2- 1/2" spacers for above bolts
1- permacap gas cap (optional)
1- large can of patience!!!

Here are the parts I got from the local wrecking yard:
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:22 AM   #2
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
more pics of junkyard parts
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:24 AM   #3
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
sidemarker light
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:26 AM   #4
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
backside of light,
You will need to grind smooth the ridges around the bolt holes on this side. Also grind off the white ridges on the ends near the bolt holes.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:47 AM   #5
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Here is the top of the fuel filler neck. You will need to weld on an exhaust reducer fitting that goes from 2" ID to 1 1/2"OD on the bottom. I cut the filler length to just below the vent hole fitting.
I could only find a 2" ID to 1 1/2" ID so I had the fuel filler hose stretched with an exhaust pipe stretcher.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:50 AM   #6
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Here is a pic of the sidemarker hole where the lense goes. My fender had this metal backing on it.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:51 AM   #7
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
another pic without the light.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:52 AM   #8
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Here is the backside of the fender.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 12:54 AM   #9
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
You have to cut out the basket.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:05 AM   #10
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
All that is really involved is cutting the fuel door to match the width and height of the sidemarker lense. Measure between the white ridges up and down (approx. 2 1/2"), but measure to just outside the bolt holes ( about 1/8" past on both ends turns out just past 3 1/2" length). My fuel door faceplate (big round part) seperated from my hinge piece, so I had it welded together again.
You can see the weld spot on the side in this pic.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:20 AM   #11
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Drill the holes for the lense and cut out a notch for the light. I used the original screws and just cut them off on the back side.
Now the bolt flanges on the back part of the hinge base will need to be cut off. Sorry no pics, but you will know which ones they are. They are little tabs with nuts welded on the backside. These were used to bolt the hinge on the S10. Feel free to try and make these work for you, but I couldn't, so I cut them even.
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:26 AM   #12
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Here comes the hard part. Drill 2 holes in the lip of the hole on the fender (where the light goes) These will be used to mount the hinges in place. While your at it drill the holes on the opposite side also. These holes will be used to hold on the plastic fuel tray.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:33 AM   #13
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Next hold the assembly (hinge assembly with lense attached) up in the hole. You need to open and close the assembly while holding it in place to get the alignment right. The best way is to hold the hinge underneath while the lense is in the right spot. Have your helper open the door slowly and then mark the through the holes you drilled in the lip to the hinge. TRIPLE CHECK YOUR MARKINGS!!!!!!! I cannot stress that enough. Then pull the assembly and drill the holes. Make sure they line up appropriately after you drill them. Next bolt it in. I had to add some washers as spacers between the fender and the hinge to help bring the back half of the hinge more flush.
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:34 AM   #14
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Here it is installed:
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:35 AM   #15
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Another (again)
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:45 AM   #16
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Next bolt on the fuel tray to the filler neck.
I actually bolted on mine upside down, with the hole in the filler neck towards the top. This makes it easier to fill with gas. I tried it the normal way, but there is not much room, so this was the fix. It doesn't seem to affect anything. Hook up the hoses (the filler hose and the vent hose). Next hold the assembly (filler neck with tray) up to the hole. Find where you will need to trim the tray, then pull the tray off and trim what you need to trim. You will need to do some trial and error here. What I did was leave it loose, take it to the gas station, Insert the gas nozzle, then mark the location of the tray. I also marked the holes I drilled earlier on the fuel tray.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:51 AM   #17
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Heres another of the filler neck installed. The Blazer tank inlet and the filler neck match almost perfect. When I installed the fuel tray I added spacers between the tray and fender. Once again to give a little more room when adding fuel.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 01:56 AM   #18
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Drill the holes in the tray for the bolts (once again TRIPLE CHECK before you drill. There isn't alot of room to play with on the tray. You might need to do a little 'tweaking' and bending to get everything to line up properly.
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:02 AM   #19
JadeEmperor
Registered User
 
Join Date: Aug 2002
Location: Phoenix, AZ 85018
Posts: 102
Awesome job


Great how-to, thanks for the info. Seems pretty straight forward, some items tedious but as you said I'm sure the key is checking your measurments and marks.

Keep us posted on other projects.
__________________
Jimmie
Modern Vintage Autoworks
- '70 Chevy C10
- '74 Chevy C30 3+3 Dually
- '04 Chevy Colorado

Built, NOT, Bought. If you build it...they will ENVY!

Drive Slow, Scrape Hard, or Take Your Truck and GO HOME!
JadeEmperor is offline   Reply With Quote
Old 11-17-2003, 02:03 AM   #20
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Make sure when you open the door, the lense doesn't hit the side of te bed. I remedied this by bending the hinge a little, so it didn't open to a full 90 degrees.
Here is the reason for the Permacap:
I installed everything and put the regular gas cap on and put the light in. The light harness hit the gas cap. So I got the permacap because it has a lower profile. Now the light clears just fine. I still have to remove the cap to fill the tank (California gas nozzles have huge adapters on them and they won't fit in the light hole well). But I really don't mind much.
Here are some pics of the final product:
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:04 AM   #21
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
more
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:06 AM   #22
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Another
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:07 AM   #23
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
One More
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:12 AM   #24
jorgensensc
Registered User
 
jorgensensc's Avatar
 
Join Date: Jul 2003
Location: Cypress, Tx
Posts: 4,006
Since they seem to go together, here is the link to the blazer tank install:
BLazer Tank Install

Also I put a new light harness in and zip tied it discreetly to the hinge after I wrapped it in electrical tape.
Hope you enjoyed this post!!!
It's really not that hard, just tedious and it takes a little tweaking.
If you have any questions, please feel free to ask!
Shawn
Attached Images
 
__________________
1972 C20 Suburban- Big Blue Betty
'56 Chevy Bel Air Sedan- Frame up Restoration

-What would you attempt to achieve if you knew you could not fail?-

-I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door-

R.I.P. EAST SIDE LOW LIFE
jorgensensc is offline   Reply With Quote
Old 11-17-2003, 02:21 AM   #25
jugernot
Life, Be In It.....
 
jugernot's Avatar
 
Join Date: Oct 2003
Location: Novato, California
Posts: 1,498
Thumbs up

Wow that is really really cool. Great job thanks for sharing.
jugernot is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:18 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com