Am I missing something? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Belsh** · 03-19-2024, 06:11 PM

Been cutting some of the floor out on my 70 C10 and noticed the 2 holes in the chassis rails (in picture), they line up with the trans crossmember, Looks like there should there be some fixings through them?

Thanks

**LockDoc** · 03-19-2024, 10:24 PM

Quote:

Originally Posted by Belsh

Been cutting some of the floor out on my 70 C10 and noticed the 2 holes in the chassis rails (in picture), they line up with the trans crossmember, Looks like there should there be some fixings through them?

Thanks

I'll check the 1/2 ton bare frame I have in the morning and see what is there. I think it should have bolts in it.

**jerry moss** · 03-19-2024, 10:29 PM

you sir are correct, a lot of times they don't get put back because the cab mounts get smashed down and it's a ***** to put them back in.

**LockDoc** · 03-20-2024, 08:39 AM

-
Here is a picture of my 1/2 ton frame.

**Belsh** · 03-20-2024, 09:45 AM

Quote:

Originally Posted by LockDoc

-
Here is a picture of my 1/2 ton frame.

Thanks as always, I think I will tack weld some nuts on from the top to facilitate fixing the bolts from below as I suspect getting to them is rather tricky as Jerry has alluded to!!

68Gold/white · 03-20-2024, 02:59 PM

Wrap a piece of masking tape on the nut. That will allow a box end wrench to hold it while starting the bolt.

**Belsh** · 03-20-2024, 03:21 PM

Quote:

Originally Posted by 68Gold/white

Wrap a piece of masking tape on the nut. That will allow a box end wrench to hold it while starting the bolt.

Do you not recommend tacking the nuts on? I figured it will make life easier if i ever have to remove the bolts

68Gold/white · 03-20-2024, 04:07 PM

Nothing wrong with welding....

Accelo · 03-20-2024, 04:25 PM

The early trucks had this end piece riveted onto the cross-member.
The only method to get it out was to hammer one side forward and the other back. This spread the frame slightly and knocked all kinds of dirt and crap loose in the process.
Later ones were bolted.
To get these out easier, I just loosened the bolts, at the cross-member, and removed the ones from the frame. Made it a lot easier to complete the R&R.
The bolts came in from the top and I didn't have to remove them from between the frame and cab to get the cross-member out.
I never did determine exactly when this change was made.

Nothing wrong with welding to nuts to the top of the frame. Typically one doesn't have access to pull this off like you do.

**dmjlambert** · 03-21-2024, 06:43 PM

Was this truck working without the crossmember attached? Trying to figure that part out.

*Casper42* · 03-21-2024, 08:57 PM

Yes - a proper heading on your post

**Belsh** · 03-22-2024, 02:40 AM

Quote:

Originally Posted by dmjlambert

Was this truck working without the crossmember attached? Trying to figure that part out.

Ive only done about 50 miles in it since purchase but seemed to drive ok for a 53 year old truck, there are fixings on the bottom of of the crossmember too which are in place which was why I wasnt sure if top ones were supposed to be there or not.

**Belsh** · 03-22-2024, 02:42 AM

Quote:

Originally Posted by Casper42

Yes - a proper heading on your post

Please accept my sincere apologies, in future I shall run any posts past your good self for approval before posting......

**70STOVEBOLT** · 03-25-2024, 01:25 PM

Quote:

Originally Posted by Belsh

Please accept my sincere apologies, in future I shall run any posts past your good self for approval before posting......

**MySons68C20** · 03-25-2024, 02:42 PM

Quote:

Originally Posted by Belsh

Please accept my sincere apologies, in future I shall run any posts past your good self for approval before posting......

Most polite way to say.......you know!!

03-19-2024, 06:11 PM	#1
Belsh Junior Member Join Date: Oct 2022 Location: Whitley bay UK Posts: 62	Am I missing something? Been cutting some of the floor out on my 70 C10 and noticed the 2 holes in the chassis rails (in picture), they line up with the trans crossmember, Looks like there should there be some fixings through them? Thanks Attached Images

03-19-2024, 10:29 PM	#3
jerry moss Born Psycho Join Date: Feb 2001 Location: brentwood,cal,usa Posts: 4,742	Re: Am I missing something? you sir are correct, a lot of times they don't get put back because the cab mounts get smashed down and it's a ***** to put them back in. __________________ jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA

03-20-2024, 08:39 AM	#4
LockDoc The Older Generation Join Date: Aug 2006 Location: Montezuma, Iowa Posts: 25,331	Re: Am I missing something? - Here is a picture of my 1/2 ton frame. Attached Images __________________ Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 -

03-20-2024, 02:59 PM	#6
68Gold/white Registered User Join Date: Sep 2011 Location: Ark City, Kansas Posts: 3,280	Re: Am I missing something? Wrap a piece of masking tape on the nut. That will allow a box end wrench to hold it while starting the bolt.

03-20-2024, 04:07 PM	#8
68Gold/white Registered User Join Date: Sep 2011 Location: Ark City, Kansas Posts: 3,280	Re: Am I missing something? Nothing wrong with welding....

03-20-2024, 04:25 PM	#9
Accelo Registered User Join Date: Mar 2015 Location: washington Posts: 2,161	Re: Am I missing something? The early trucks had this end piece riveted onto the cross-member. The only method to get it out was to hammer one side forward and the other back. This spread the frame slightly and knocked all kinds of dirt and crap loose in the process. Later ones were bolted. To get these out easier, I just loosened the bolts, at the cross-member, and removed the ones from the frame. Made it a lot easier to complete the R&R. The bolts came in from the top and I didn't have to remove them from between the frame and cab to get the cross-member out. I never did determine exactly when this change was made. Nothing wrong with welding to nuts to the top of the frame. Typically one doesn't have access to pull this off like you do.

03-21-2024, 06:43 PM	#10
dmjlambert Senior Member Join Date: Apr 2016 Location: Cypress, TX Posts: 3,565	Re: Am I missing something? Was this truck working without the crossmember attached? Trying to figure that part out.

03-21-2024, 08:57 PM	#11
Casper42 Account Suspended Join Date: Nov 2022 Location: Seattle, WA Posts: 312	Re: Am I missing something? Yes - a proper heading on your post



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.