Sean Murphy Induction - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jayss109 · 11-28-2006, 07:32 PM

I have to give high praise to Sean Murphy and his crew. They an OUTSTANDING job on my poor tired quadrajet. I had been fighting with my edlebrock carb for years, and my engine never did run right.

I literally bolted on the qjet, bent a new fuel line and turned the key. Truck runs like a champ now!

Sean was very proffesional and he knows his stuff!!

Highly recommended!!

ps, I get nothing from this, just believe in word of mouth. Quality work is hard to find these days!

Jason

http://www.smicarburetor.com/
________
Brunette blonde

krue · 11-28-2006, 08:19 PM

Thanks for the heads up.

c10crazy · 11-29-2006, 07:46 PM

Do they restore the finish on it?. Can I ask you what they charge?

Jayss109 · 11-29-2006, 08:20 PM

They do finish restoring as well. I didnt get it (I can be cheap sometimes!! lol)

I paid $225 + tax for the full deal. They also added a part throttle adjustment, which i havent even played with yet. This allows you to set how far the rods are in the jet up and down before the vacuum pulls them out of the jet. So for those part throttle romps, when you dont NEED to open it up, you can get the mixture good!
I literally bolted it on and fired it up. adjusted the idle a tad and havent touched it. I believe my part throttle is a little rich, so i plan on playing with it this weekend.

Send them an email and Sean will get back to you right away with the cost of coating and whatnot. I think you can even buy a qjet straight from them for $325. They have the form online to fill out about all the engine specs, vechile specs, trans specs etc. This makes sure that they get everything right. Sean even made some suggestions regarding my torque convertor being too tight. (Gonna get replaced soon anyway!!)

Hope that helps

Jason
________
Free kohls gift card

11-28-2006, 07:32 PM	#1
Jayss109 Active Member Join Date: May 2005 Location: San Jose, CA Posts: 235	Sean Murphy Induction I have to give high praise to Sean Murphy and his crew. They an OUTSTANDING job on my poor tired quadrajet. I had been fighting with my edlebrock carb for years, and my engine never did run right. I literally bolted on the qjet, bent a new fuel line and turned the key. Truck runs like a champ now! Sean was very proffesional and he knows his stuff!! Highly recommended!! ps, I get nothing from this, just believe in word of mouth. Quality work is hard to find these days! Jason http://www.smicarburetor.com/ ________ Brunette blonde Last edited by Jayss109; 04-27-2011 at 11:43 PM.

11-28-2006, 08:19 PM	#2
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,450	Re: Sean Murphy Induction Thanks for the heads up. __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

11-29-2006, 07:46 PM	#3
c10crazy Like a Rock! Join Date: May 2002 Location: USA Posts: 1,092	Re: Sean Murphy Induction Do they restore the finish on it?. Can I ask you what they charge? __________________ 69 LWB Runs great - work in progress Mess with me and you mess with the whole trailer park!

11-29-2006, 08:20 PM	#4
Jayss109 Active Member Join Date: May 2005 Location: San Jose, CA Posts: 235	Re: Sean Murphy Induction They do finish restoring as well. I didnt get it (I can be cheap sometimes!! lol) I paid $225 + tax for the full deal. They also added a part throttle adjustment, which i havent even played with yet. This allows you to set how far the rods are in the jet up and down before the vacuum pulls them out of the jet. So for those part throttle romps, when you dont NEED to open it up, you can get the mixture good! I literally bolted it on and fired it up. adjusted the idle a tad and havent touched it. I believe my part throttle is a little rich, so i plan on playing with it this weekend. Send them an email and Sean will get back to you right away with the cost of coating and whatnot. I think you can even buy a qjet straight from them for $325. They have the form online to fill out about all the engine specs, vechile specs, trans specs etc. This makes sure that they get everything right. Sean even made some suggestions regarding my torque convertor being too tight. (Gonna get replaced soon anyway!!) Hope that helps Jason ________ Free kohls gift card Last edited by Jayss109; 04-27-2011 at 11:43 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.