The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-07-2020, 06:59 PM   #1
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Spark plug wires to get and set up?

I had placed the wires in a box when I did my teardown years ago and planned to reuse them but I am seeing ripped boots and a melted wire. The L31 I think is the same firing order and all as the previous 350 I had before I swapped. The plan was to reference my pics of the teardown and follow the cylinder numbers I marked at the plug end and the numeric order I marked on the distributor cap. It wasnt a firing order numbering just a left right in order so I plugged up the right spots again.

I was thinking to get an AC Delco set of wires since I have bought new plugs that are AC Delco Part # R44LTS. Is there any particular year and models to search by that would give me the right length to hopefully dodge the headers where it might melt? I would think this time to get heat shield wraps for the boots this time, any that are recommended?

Ill post pics of the teardown and where I am now.
Attached Images
     
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 11-07-2020, 07:37 PM   #2
truckster
Senior Member
 
truckster's Avatar
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,760
Re: Spark plug wires to get and set up?

I used Taylor wires and ordered a set for a 76 Corvette. I ran them under the rams horns just like the factory did. I think that would work for your headers as well.
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson
truckster is offline   Reply With Quote
Old 11-07-2020, 07:40 PM   #3
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: Spark plug wires to get and set up?

With headers your best bet is to buy a set of cut to length wires and put the ends on yourself. Very easy to do.
Run the wires like on a corvette. Down the back of each head and then along the pan rail and up to each plug.
Plug wire brackets are available to do that.
geezer#99 is offline   Reply With Quote
Old 11-08-2020, 11:17 AM   #4
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Farmington, New Mexico
Posts: 6,170
Re: Spark plug wires to get and set up?

+1 I use accel cut to fit wires with ceramic spark plug boots.

https://www.jegs.com/i/Accel/110/9002C/10002/-1

You’ll need a good spark plug wire crimping tool like this:
https://www.summitracing.com/parts/s...QaAu09EALw_wcB
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 315/75/16's
‘87 IROC-Z all original 50K mile survivor TPI 305 IROC Blue
‘10 Camaro 2SS/RS Aqua Blue Metallic #93 -version 2.0
57taskforce is offline   Reply With Quote
Old 11-08-2020, 11:25 AM   #5
Getter-Done
Senior Member
 
Getter-Done's Avatar
 
Join Date: Dec 2009
Location: TN.
Posts: 7,623
Re: Spark plug wires to get and set up?

Quote:
Originally Posted by 57taskforce View Post
+1 I use accel cut to fit wires with ceramic spark plug boots.

https://www.jegs.com/i/Accel/110/9002C/10002/-1

You’ll need a good spark plug wire crimping tool like this:
https://www.summitracing.com/parts/s...QaAu09EALw_wcB
I have used this same set.
They are Great









.
__________________
________________________________________________________________________________________
____________________________________________
84 Chevy K-20
63 Impala (my high school car)

http://67-72chevytrucks.com/vboard/s...Crew Cab Build
Getter-Done is online now   Reply With Quote
Old 11-08-2020, 09:58 PM   #6
kaycee
Registered User
 
kaycee's Avatar
 
Join Date: Jan 2000
Location: Wyoming USA
Posts: 2,445
Re: Spark plug wires to get and set up?

I run the MSD streetfire wires on both my rigs in the stock location with headers . They come with a little crimp tool you put in the vice works like a champ
__________________
2001 Silverado K-1500
2005 FXDWG stage3
69 CHEVY Short/Step 327/4L60 373 posi
63 IMPALA 327
kaycee is offline   Reply With Quote
Old 11-08-2020, 10:59 PM   #7
burnin oil
Registered User
 
Join Date: Jan 2013
Location: Eastern TN
Posts: 1,919
Re: Spark plug wires to get and set up?

I like the MSD low resistance wire myself as it has proven to be very durable. I had a header tube that was very close to the boot. The boot would die and I would just cut it off and replace the end. I could do this a couple times by leaving the wire long.

As for routing. Under the headers is better looking but I think its a pain to work on them, especially if you ziptie them together. Its ugly but I find spaghetti style over the cover to work the best on my headers. Alot of it really depends on how the tube and plug end occupy the same space. My old headers had 6 wires under and 2 over. I did this purely for wire longevity. I have a solid cam on my motor and its still easier for me to run over the top on this set of headers even though I have to pull the valve cover every once in a while. I do tend to change the plugs more than checking valve lash. I have one wire with the woven sleeve over it thats cut to cover the boot. I had so much radiant heat that the boot would crack after a few thousand miles. I tried all the wire ends other than the ceramic ones.

Looking at your headers make me.gringe. they remind me of a set I had that required shorty plugs for clearance. If that is your case get real comfy with the manufacturers plug guide then cross reference. My shorty was actually a lawn mower plug. By dropping the first letter of that I managed to get a standard plug (identical) for $2. Lawn mower plugs add an extra letter to the front to signify things like brings and Stratton. $5 plug in lawn in garden is $2 in automotive section of Walmart. Price at Walmart last year.
burnin oil is offline   Reply With Quote
Old 11-12-2020, 03:49 PM   #8
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Re: Spark plug wires to get and set up?

Quote:
Originally Posted by truckster View Post
I used Taylor wires and ordered a set for a 76 Corvette. I ran them under the rams horns just like the factory did. I think that would work for your headers as well.
Quote:
Originally Posted by geezer#99 View Post
With headers your best bet is to buy a set of cut to length wires and put the ends on yourself. Very easy to do.
Run the wires like on a corvette. Down the back of each head and then along the pan rail and up to each plug.
Plug wire brackets are available to do that.
Thanks for the replies guys, how about the spark plug gap on this new L31 and running AC Delco Part # R44LTS plugs? .045 or .060?
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 11-12-2020, 05:52 PM   #9
truckster
Senior Member
 
truckster's Avatar
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 7,760
Re: Spark plug wires to get and set up?

Quote:
Originally Posted by msg View Post
Thanks for the replies guys, how about the spark plug gap on this new L31 and running AC Delco Part # R44LTS plugs? .045 or .060?
The factory started out at .060 when they went to HEI, but switched to .045. I would go with .045.
__________________
I have sworn upon the altar of God, eternal hostility against every form of tyranny over the mind of man. - Thomas Jefferson
truckster is offline   Reply With Quote
Old 11-12-2020, 11:43 PM   #10
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Re: Spark plug wires to get and set up?

Thanks Truckster, I will gap them to .045.
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 11-15-2020, 08:46 PM   #11
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Re: Spark plug wires to get and set up?

Ok, I ordered the 67 corvette Taylor set to start with and bought the heat shield sleeves for the boots as well. I tried running them under vs over the top to see if I can make that work. Ill attach pics of what I have and see if you guys think its safe.. and if I wired this thing up right.

I assumed the HEI diagram and the firing order is correct for an L31? I used it as a guide on how to run the wires.





After running the wires I learned that the driver side header is designed differently than the passenger side. The 1st cylinder exhaust makes it way too tight of a space to sneak a wire into. Every time I tried it just looked like a no go. Maybe the shorty plug that burnin oil mentioned would help give better clearance?

As another option I took the wire and ran it out to the frame and under the engine mount. Not pretty but if I install a clip on the firewall instead of tape it would keep it from dangling onto the back of the header.

Here are some of the pics of that tight spot on the driver side and trying to route the wire under the header.
Attached Images
  
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 11-15-2020, 08:49 PM   #12
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Re: Spark plug wires to get and set up?

Here is the alternate route going out to the frame, under the engine bracket and pinning the wire against the firewall to keep it from touching the exhaust.
Attached Images
  
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Old 11-15-2020, 08:51 PM   #13
msg
Registered User
 
Join Date: Feb 2013
Location: GA
Posts: 1,313
Re: Spark plug wires to get and set up?

Here are pics of how the other driver side wires then look.
Attached Images
  
__________________
Progress thread for my 66
http://67-72chevytrucks.com/vboard/s...d.php?t=623848
msg is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:11 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com