What did everyone get done this weekend? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Boise69 · 11-19-2006, 10:04 PM

YES IT IS. I bought it in IDAHO 3 years back and i must admit i dont know much about carbs but i've been fiddling with it to the point it drives but not that well. i would think that the elevation diff certainly would matter but how to correct i do not know. Hopefully Mark can help me.

*trkklr77* · 11-19-2006, 10:14 PM

i went to the indy speedway museum and track tour, i got to go all of 30mph on one of the fastest tracks im america!!!!!!!

i have never seen such a wide varitey of motors in my life. every thing from a 4cyl 938cui 100hp 1918 crank start to a 16cyl 1.8L with 49mm stroke, oh yeah it made 790-810hp :yikes:. a turbine drive side motor, where you sit 6" from a jet engine and a 315" 6cyl sprint car.

**truckdude239** · 11-19-2006, 10:16 PM

nothing but i am going to pick up a free 305 engine tomorrow

70 net440 · 11-19-2006, 10:16 PM

Put a wiper switch and a gas pedal in my middle kid's '67. Finally put the Pertronix kit in my youngest's '71.

timcos · 11-19-2006, 10:39 PM

I tuned up my truck.

Set the RPMs to 600...got it setting at 5 DBTDC. Runs a whole lot smoother now. Going to install HEI dizzy this coming week. Should be a decent daily driver then.

Also...installed the new washer pump, new tubing and ran the wires to the cab...connecting them tomorrow because I am going to drop my gage bezel to get to the wires I need. I did not do it saturday as I wanted to buy a bunch of 194 bulbs so I can replace them all in the dash...I have a few out...and since it will opened up...might as well replace them.

Boise69 · 11-19-2006, 10:42 PM

Hey Tim(cos)

Did you buy the whole washer kit and if so which place did you get it from? I'm looking at the kit on LMC, was it an easy install? I have to do the same.

Botietruck · 11-19-2006, 10:52 PM

Primered & painted my garage interior...after insulating & sheetrocking. Now to put everything back in it and installing the lights/etc.

timcos · 11-19-2006, 10:57 PM

I did it a little more manual....I am working on a FAQ...but here is what I did thus far...finishing it up tomorrow.

I am down to the "Run them into the cab." step

Universal pump (Checkers) 19.99, new tubing (Checkers) 4.99, some tape and connectors - a few cents.

Some Christmas music makes the whole job more pleasant as well.

The universal pump comes with some little goodies like a tee, connectors etc. I am using goodies from my "professional" wiring kit...I will take pics etc.

1. New circuit for water flow

a. Install pump to fender ahead of the reservoir or your own chosen location.

b. Attach tubing from reservoir to suction on pump.

c. Cut old tubing at firewall.

d. Extend back the squirter tubing in your hand and cut to equal length (long enough to meet in the middle.) Be careful to not tug too hard and pull them off the squirters.

e. Attach squirter tubing to new T (comes with universal pump) and attached new hose (6 ft – 4.99 at checkers) to third leg of the new T.

f. Run new tubing down the guide to the side of the truck and forward. Attach it to the output of the pump

2. New electrical circuit so your pump will pump when you depress the stock switch.

a. Attach two wires to pump wire with approved electrical connection procedures.

i. I used 6 feet each of 18 gage yellow (power) and dark blue (ground)

b. Run them into the cab

c. Remove gage panel.

i. http://www.67-72chevytrucks.com/vboa...d.php?t=164357

d. Tap onto the YELLOW wire at the wiper motor. It is switched already.

i. Use Yellow wire running to the cab for connection.

e. Tap into the dark blue (ground) wire from under the dash at the new motor.

i. Use Dark Blue wire running to the cab for connection.

3. Reassemble everything you disassembled.

*Billla* · 11-19-2006, 11:19 PM

I finally finished my )(*&#*$+)_(%)(&#$ cam swap :-D. I tore my bicep tendon pulling the truck into the garage 8/6 to do the swap, and I'm just getting back in the game enough to do real work. It's kind of a nice reminder that I'm getting better

Boise69 · 11-19-2006, 11:25 PM

Thank you Tim! It was saved in my 'how to do folder' for later reference.

Americanrider · 11-19-2006, 11:48 PM

I hit the yards on Saturday, scored a van tilt ($25) and a rust-free pass inner fender ($10) Then on Sunday I scored a shorty 67 rolling rusty shell & frame project for 200 bones. Broke but happy!

lowrollin70gmc · 11-20-2006, 12:12 AM

Lost my voice at the NDSU/SDSU football game. Our (NDSU's) 12th man definitely helped the win.

Fantasied about being with my truck tomorrow afternoon, it's been months. I have to remember not to cry on the paint job.

jimmydean · 11-20-2006, 12:28 AM

I got my air gauges mounted and started to mount my switch box. When I pulled up the rubber mat to run the wires, I got side tracked by 37 years of dirt and grime. I spent way too much time trying to clean up the drivers side and ran out of daylight.

Today was solid rain and the forcast is rain until Friday. All my wires are there, I just need to trim and tie everything, then fire up the compressor and see if my air lines are as leak-proof as I hope.

If next weekend sucks less, I might have my truck on it's own wheels and under it's own power again. I will post som pics for sure too.

**N2TRUX** · 11-20-2006, 12:36 AM

This was my weekend off and I got a lot done. The weather was awesome so I took advantage of it. Friday night I took the family to dinner so I could have that weekend obligation fulfilled. Saturday I went and toured our new Church building then picked up my 04 Dodge at the body shop. I had the front bumper cap and mirrors repainted and the whole truck buffed out. Then I went and had the Snuglid put back on. It had been shipped back to Snugtop because of defective paint. They did an awesome job of making it look like a new one.

Saturday night I took the wife out to dinner then in the 77 then we went to the local car s cruise. This was the last night for the season so the turn out was huge. They set an all time record with a fitting number of 427 cars and trucks.

Sunday after church I started detailing my Dodge to get it ready to sell. Then I spent some time cleaning up my 06 Crewcab. The whole while I was making plans for what I want to do to the 77 over the winter....

Robert1970C20rstbukt · 11-20-2006, 12:40 AM

Well I figured out the Suburban needs all new brake hoses, gonna take awhile before I can afford 'em. Tomorrow I plan on getting the '69 grille and bumper on the truck.

*Billla* · 11-20-2006, 01:26 AM

Quote:

Originally Posted by 409biscayne

box sides

Box sides? :-D

jamis · 11-20-2006, 09:05 AM

Open my garage door, took the cover off my project, sat in a rocking chair smoking a montecristo and stared at it.....I need to get motivated

birdie · 11-20-2006, 11:50 AM

Saturday I repaired the linkage on my choke so I was able to hook up the cable. It sure is nice to have the truck run on it's own when the engine is cold. Also got a 81 chevy van for free. It has a fresh rebuilt tranny with tilt column and power steering pump, just got to get it home. Yesterday I put in a different seat, that I had scored for free and I got my mig welder all ready to go. Things are starting to look up.

mjensen · 11-20-2006, 01:28 PM

Went over to Timcos house to see his project.

70rs/ss · 11-20-2006, 04:16 PM

Started updating the GSA truck I brought home last weekend, rebuilding the 2 barrel (yeah I know why not a 4 barrel) but I need it to run so I can see if the motor is OK or not. Drained the many year old gas and put fresh in it, and scoped out one of my HEI to put in it, Then drive it!! I can't wait to make smoke come forth from the tires and 4.11's!!! Oh Yeah, I popped the rear cover to ensure 4.11's and they are there!! Put it back together with a new gasket and royal purple gear lube, almost ready, I hope the neighbors are!! I have a 5 day weekend for turkey day coming, so the 69ish GMC I hauled home for free will be stripped over the week long weekend and hopefully the 68 Short Fleet 3/4ton 4X4 will be near road ready at weeks end!!

11-19-2006, 10:04 PM	#26
Boise69 The Hammer Man Join Date: Oct 2006 Location: Wilmington, NC Posts: 864	Re: What did everyone get done this weekend? YES IT IS. I bought it in IDAHO 3 years back and i must admit i dont know much about carbs but i've been fiddling with it to the point it drives but not that well. i would think that the elevation diff certainly would matter but how to correct i do not know. Hopefully Mark can help me. __________________ Boise69. Bought in Boise ID and its a '69 ___________________________________________ 1969 Chevy C-10 SWB 350/400 - drivable project www.americanhammer.com 2013 MBZ Sprinter customized 2005 MBZ Sprinter Van 2004 Land Rover Discovery 2001 Yamaha Road Star 1997 MBZ E420 1989 Ferrari Mondial T

11-19-2006, 10:14 PM	#27
trkklr77 Account Suspended Join Date: Aug 2006 Location: vacaville ca, because it as far from indy as i can be Posts: 777	Re: What did everyone get done this weekend? i went to the indy speedway museum and track tour, i got to go all of 30mph on one of the fastest tracks im america!!!!!!! i have never seen such a wide varitey of motors in my life. every thing from a 4cyl 938cui 100hp 1918 crank start to a 16cyl 1.8L with 49mm stroke, oh yeah it made 790-810hp :yikes:. a turbine drive side motor, where you sit 6" from a jet engine and a 315" 6cyl sprint car. Attached Images

11-19-2006, 10:16 PM	#28
truckdude239 Senior Member Join Date: Sep 2005 Location: Lewisville, Nc Posts: 10,217	Re: What did everyone get done this weekend? nothing but i am going to pick up a free 305 engine tomorrow __________________ David fuller Ase Certified Mechanic Click here to help support our board!! 1971 Chevy c-10 under going a 4.8l LSx swap Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=421305 2007 Honda Accord my daily 145kmiles 2002 Honda Accord 4 door With 330k(sisters car) 2005 toyota Avalon 228k( brothers car) 2002 Sububran 5.3 245k 2000 Tahoe 5.3l 378 General manager for Marco's Carwash & lube

11-19-2006, 10:16 PM	#29
70 net440 Junior Member Join Date: Sep 2003 Location: yreka, ca Posts: 270	Re: What did everyone get done this weekend? Put a wiper switch and a gas pedal in my middle kid's '67. Finally put the Pertronix kit in my youngest's '71. __________________ 63 C10 70 Coronet R/T 67 C10 70 Dart Swinger 71 K10

11-19-2006, 10:39 PM	#30
timcos Chief Honcho In Charge Join Date: Aug 2006 Location: Bentonville AR Posts: 970	Re: What did everyone get done this weekend? I tuned up my truck. Set the RPMs to 600...got it setting at 5 DBTDC. Runs a whole lot smoother now. Going to install HEI dizzy this coming week. Should be a decent daily driver then. Also...installed the new washer pump, new tubing and ran the wires to the cab...connecting them tomorrow because I am going to drop my gage bezel to get to the wires I need. I did not do it saturday as I wanted to buy a bunch of 194 bulbs so I can replace them all in the dash...I have a few out...and since it will opened up...might as well replace them. __________________ 1992 1500 4x4 Shortbed 1984 Ford F250 Supercab Longbed 6.9L Diesel 1972 K10 Cheyenne Super Fleetside Short Bed - 350 - A/C 1971 VW SuperBeetle 1960 Wife 1984 Son 1986 Son 1989 Son Previous Trucks 1967 C10 SWB (1980-1981) 1971 C10 LWB (1998-2004) Last edited by timcos; 11-19-2006 at 10:40 PM.

11-19-2006, 10:42 PM	#31
Boise69 The Hammer Man Join Date: Oct 2006 Location: Wilmington, NC Posts: 864	Re: What did everyone get done this weekend? Hey Tim(cos) Did you buy the whole washer kit and if so which place did you get it from? I'm looking at the kit on LMC, was it an easy install? I have to do the same.

11-19-2006, 10:52 PM	#32
Botietruck '71 chevy s.bed/s.side Join Date: Mar 2005 Location: Chesapeake, VA Posts: 1,571	Re: What did everyone get done this weekend? Primered & painted my garage interior...after insulating & sheetrocking. Now to put everything back in it and installing the lights/etc. __________________ STILL PLAYS WITH CARS...AND TRUCKS!! Parents! Be good to your kids...they get to choose your nursing home! 250 I-6 with a 3 speed Saginaw and Borg Warner Overdrive...She's got overdrive!

11-19-2006, 10:57 PM	#33
timcos Chief Honcho In Charge Join Date: Aug 2006 Location: Bentonville AR Posts: 970	Re: What did everyone get done this weekend? I did it a little more manual....I am working on a FAQ...but here is what I did thus far...finishing it up tomorrow. I am down to the "Run them into the cab." step Universal pump (Checkers) 19.99, new tubing (Checkers) 4.99, some tape and connectors - a few cents. Some Christmas music makes the whole job more pleasant as well. The universal pump comes with some little goodies like a tee, connectors etc. I am using goodies from my "professional" wiring kit...I will take pics etc. 1. New circuit for water flow a. Install pump to fender ahead of the reservoir or your own chosen location. b. Attach tubing from reservoir to suction on pump. c. Cut old tubing at firewall. d. Extend back the squirter tubing in your hand and cut to equal length (long enough to meet in the middle.) Be careful to not tug too hard and pull them off the squirters. e. Attach squirter tubing to new T (comes with universal pump) and attached new hose (6 ft – 4.99 at checkers) to third leg of the new T. f. Run new tubing down the guide to the side of the truck and forward. Attach it to the output of the pump 2. New electrical circuit so your pump will pump when you depress the stock switch. a. Attach two wires to pump wire with approved electrical connection procedures. i. I used 6 feet each of 18 gage yellow (power) and dark blue (ground) b. Run them into the cab c. Remove gage panel. i. http://www.67-72chevytrucks.com/vboa...d.php?t=164357 d. Tap onto the YELLOW wire at the wiper motor. It is switched already. i. Use Yellow wire running to the cab for connection. e. Tap into the dark blue (ground) wire from under the dash at the new motor. i. Use Dark Blue wire running to the cab for connection. 3. Reassemble everything you disassembled. __________________ 1992 1500 4x4 Shortbed 1984 Ford F250 Supercab Longbed 6.9L Diesel 1972 K10 Cheyenne Super Fleetside Short Bed - 350 - A/C 1971 VW SuperBeetle 1960 Wife 1984 Son 1986 Son 1989 Son Previous Trucks 1967 C10 SWB (1980-1981) 1971 C10 LWB (1998-2004)

11-19-2006, 11:19 PM	#34
Billla Account Suspended Join Date: Sep 2005 Location: Monroe, WA Posts: 3,815	Re: What did everyone get done this weekend? I finally finished my )(&#$+)_(%)(&#$ cam swap :-D. I tore my bicep tendon pulling the truck into the garage 8/6 to do the swap, and I'm just getting back in the game enough to do real work. It's kind of a nice reminder that I'm getting better

11-19-2006, 11:25 PM	#35
Boise69 The Hammer Man Join Date: Oct 2006 Location: Wilmington, NC Posts: 864	Re: What did everyone get done this weekend? Thank you Tim! It was saved in my 'how to do folder' for later reference.

11-19-2006, 11:48 PM	#36
Americanrider Registered User Join Date: Dec 2004 Location: NW, WA. Posts: 1,421	Re: What did everyone get done this weekend? I hit the yards on Saturday, scored a van tilt ($25) and a rust-free pass inner fender ($10) Then on Sunday I scored a shorty 67 rolling rusty shell & frame project for 200 bones. Broke but happy! Attached Images

11-20-2006, 12:12 AM	#37
lowrollin70gmc Too many projects Join Date: Mar 2004 Location: Fargo, ND land of the flat hills Posts: 1,147	Re: What did everyone get done this weekend? Lost my voice at the NDSU/SDSU football game. Our (NDSU's) 12th man definitely helped the win. Fantasied about being with my truck tomorrow afternoon, it's been months. I have to remember not to cry on the paint job. __________________ Andrew 84 GMC C1500 SWB 6.2 Diesel/700R4/3.42 "Grandpa's odd duck" 70 GMC C1500 LWB My first truck: shaved, bagged, and more: the lowrollin70gmc 68 K20 Suburban 12V Cummins/NV5600/NP205/D60/11.5AAM 3.73s "Dakota Cadillac" 63 Chevy II Nova Coupe 250 I6/T56/4.56s "Economy car" 53 Willys Wagon 350/NV4500/BW4401/HP D44/9inch “Winter Wagon” 30 Model A 16 Focus ST

11-20-2006, 12:28 AM	#38
jimmydean Registered User Join Date: May 2005 Location: Beaverton, OR Posts: 3,728	Re: What did everyone get done this weekend? I got my air gauges mounted and started to mount my switch box. When I pulled up the rubber mat to run the wires, I got side tracked by 37 years of dirt and grime. I spent way too much time trying to clean up the drivers side and ran out of daylight. Today was solid rain and the forcast is rain until Friday. All my wires are there, I just need to trim and tie everything, then fire up the compressor and see if my air lines are as leak-proof as I hope. If next weekend sucks less, I might have my truck on it's own wheels and under it's own power again. I will post som pics for sure too.

11-20-2006, 12:36 AM	#39
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,023	Re: What did everyone get done this weekend? This was my weekend off and I got a lot done. The weather was awesome so I took advantage of it. Friday night I took the family to dinner so I could have that weekend obligation fulfilled. Saturday I went and toured our new Church building then picked up my 04 Dodge at the body shop. I had the front bumper cap and mirrors repainted and the whole truck buffed out. Then I went and had the Snuglid put back on. It had been shipped back to Snugtop because of defective paint. They did an awesome job of making it look like a new one. Saturday night I took the wife out to dinner then in the 77 then we went to the local car s cruise. This was the last night for the season so the turn out was huge. They set an all time record with a fitting number of 427 cars and trucks. Sunday after church I started detailing my Dodge to get it ready to sell. Then I spent some time cleaning up my 06 Crewcab. The whole while I was making plans for what I want to do to the 77 over the winter.... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

11-20-2006, 12:40 AM	#40
Robert1970C20rstbukt Registered User Join Date: Jun 2004 Location: Beeville, Texas Posts: 1,943	Re: What did everyone get done this weekend? Well I figured out the Suburban needs all new brake hoses, gonna take awhile before I can afford 'em. Tomorrow I plan on getting the '69 grille and bumper on the truck. __________________ RJD 1984 Chevrolet C30 welding truck 454/SM465 1977 GMC C15 pickup 350/TH350 1970 Chevrolet C20 pickup 350/TH400 1970 Chevrolet K20 Suburban 454/TH350 1969 GMC 8500 478M V6/5 spd winch truck



Register or Log In To remove these advertisements.

11-20-2006, 09:05 AM	#42
jamis F.A.S.T. president Join Date: Sep 2003 Location: Florida Posts: 1,883	Re: What did everyone get done this weekend? Open my garage door, took the cover off my project, sat in a rocking chair smoking a montecristo and stared at it.....I need to get motivated __________________ F.A.S.T. President and Founder Fabricators for the Advancement of Sawsall Technology "A fear of the Sawsall is a sign of retarded sexual and emotional maturity." ~Sigmund Freud, "General Introduction to Psychoanalysis" Last edited by jamis; 11-20-2006 at 09:07 AM.

11-20-2006, 11:50 AM	#43
birdie Registered User Join Date: Nov 2005 Location: Rouleau, Saskatchewan Posts: 87	Re: What did everyone get done this weekend? Saturday I repaired the linkage on my choke so I was able to hook up the cable. It sure is nice to have the truck run on it's own when the engine is cold. Also got a 81 chevy van for free. It has a fresh rebuilt tranny with tilt column and power steering pump, just got to get it home. Yesterday I put in a different seat, that I had scored for free and I got my mig welder all ready to go. Things are starting to look up. __________________ 1946 Chevy ton truck 1972 Chev C30 1975 Scottsdale C10

11-20-2006, 01:28 PM	#44
mjensen Registered User Join Date: Jun 2006 Location: Utah Posts: 1,562	Re: What did everyone get done this weekend? Went over to Timcos house to see his project. __________________ Mike '69 GMC 3/4 ton 4x4 Build Thread

11-20-2006, 04:16 PM	#45
70rs/ss Registered User Join Date: Dec 2004 Location: Northern AZ Posts: 7,271	Re: What did everyone get done this weekend? Started updating the GSA truck I brought home last weekend, rebuilding the 2 barrel (yeah I know why not a 4 barrel) but I need it to run so I can see if the motor is OK or not. Drained the many year old gas and put fresh in it, and scoped out one of my HEI to put in it, Then drive it!! I can't wait to make smoke come forth from the tires and 4.11's!!! Oh Yeah, I popped the rear cover to ensure 4.11's and they are there!! Put it back together with a new gasket and royal purple gear lube, almost ready, I hope the neighbors are!! I have a 5 day weekend for turkey day coming, so the 69ish GMC I hauled home for free will be stripped over the week long weekend and hopefully the 68 Short Fleet 3/4ton 4X4 will be near road ready at weeks end!!

Register or Log In To remove these advertisements.