Ss Brake Lines - Master Cyl. Kit - The 1947 - Present Chevrolet & GMC Truck Message Board Network

LUV2XCLR8 · 09-09-2004, 07:34 PM

Well I got my kit from Tim Christian, Thanks buddy, and of course they did
not fit perfectly, have yet to here of someone's who did, a lil elbow grease,
a few hours of my time, yes I said hours, and wala, what do ya all think.

*Gee_Emm* · 09-09-2004, 07:43 PM

Cool, that would be a whole lot easier then bending a new set like I was planing on doing, I wonder if he sells a set for 2wds, the fuel lines would be nice to have premade too.

LUV2XCLR8 · 09-09-2004, 08:39 PM

2wd Is Available Also, It Was A Stainless Kit ( 4 Lines ) I Paid Like
$60 And Some Odd Cents, Fedex Shipped Direct To My Front Door.

*Gee_Emm* · 09-09-2004, 10:19 PM

Did you just get the up front set or did you also get the lines that run to the rear?

Alexis · 09-10-2004, 03:13 AM

kits are nice but man when they get them wrong do they get them wrong. I also had to put in some work to get them right. On my next project I think I'll bend my own lines, after looking at some bare(show off) frames at the goodguys show, the way they setup there brake and fuel line looked like a work of art. Especially with all the cool products out on the market. Wish I took my camera so you guy can see what I'm talking about but I bet it take some practice to bend brake lines good.

*Gee_Emm* · 09-10-2004, 09:11 AM

The bending is the easy and fun part, flaring the ends is were it gets tricky.

LUV2XCLR8 · 09-10-2004, 02:42 PM

Quote:

Originally Posted by Gee_Emm

The bending is the easy and fun part, flaring the ends is were it gets tricky.

I'M CHALLENGED, SO I OPTED NOT TO FLARE / BUILD MY OWN.

meathead95 · 09-10-2004, 05:57 PM

i think you should have painted the master cylinder :-)

LUV2XCLR8 · 09-10-2004, 07:16 PM

Quote:

Originally Posted by meathead95

i think you should have painted the master cylinder :-)

I HEAR YA KEITH

09-09-2004, 07:34 PM	#1
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,470	Ss Brake Lines - Master Cyl. Kit Well I got my kit from Tim Christian, Thanks buddy, and of course they did not fit perfectly, have yet to here of someone's who did, a lil elbow grease, a few hours of my time, yes I said hours, and wala, what do ya all think. __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

09-09-2004, 08:39 PM	#3
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,470	2wd Is Available Also, It Was A Stainless Kit ( 4 Lines ) I Paid Like $60 And Some Odd Cents, Fedex Shipped Direct To My Front Door. __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Big Piggy: "Goliath" 07 Kodiak C4500 Lil Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

09-10-2004, 05:57 PM	#8
meathead95 computer illiterate Join Date: Jan 2001 Location: Des Moines, IA Posts: 6,446	i think you should have painted the master cylinder :-) __________________ 72 2wd blazer 72 swb 4x4

09-09-2004, 07:43 PM	#2
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 4,002	Cool, that would be a whole lot easier then bending a new set like I was planing on doing, I wonder if he sells a set for 2wds, the fuel lines would be nice to have premade too.

09-09-2004, 10:19 PM	#4
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 4,002	Did you just get the up front set or did you also get the lines that run to the rear?

09-10-2004, 03:13 AM	#5
Alexis Member since 2000 Join Date: Dec 2000 Location: Mountain View Ca / Mexico Posts: 7,879	kits are nice but man when they get them wrong do they get them wrong. I also had to put in some work to get them right. On my next project I think I'll bend my own lines, after looking at some bare(show off) frames at the goodguys show, the way they setup there brake and fuel line looked like a work of art. Especially with all the cool products out on the market. Wish I took my camera so you guy can see what I'm talking about but I bet it take some practice to bend brake lines good.

09-10-2004, 09:11 AM	#6
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 4,002	The bending is the easy and fun part, flaring the ends is were it gets tricky.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.