"The Convict"

[Hankster]

Where it all started...

[Hankster]

I decided to go back with a turbo trans.. so I dropped the 700r4 its for sale now, and I've found a turbo 400 I'm going to try to get. I had a friend cut off and flip over my perch pads on my 12 bolt. So it'll be going in soon. Me and my folks are moving to Texas around the end of the month also. So I'm trying to get the truck drive able so we can load it onto a trailer and haul her up there.

[creamed12]

Damn I wish I could have caught you earlier in your build. I had a 1998 5.7 Vortec in a 1963 Impala. I recently swapped it for a 2002 LS1. I sold the 5.7 but I still have the harness and computer. The harness was bought new from Fuel Injection Specialties and they also did the computer. If you or anyone needs it, I am willing to sell them both for very cheap. And if I am correct, I have a programmer for that engine (gotta check on that).

[bbbc10]

there is ALOT of nice squares here in tx!!!! what part of tx yall moving too

[2000Limited]

Where is all the progress!!!! lol

[Hankster]

Originally Posted by bbbc10

there is ALOT of nice squares here in tx!!!! what part of tx yall moving too

Lufkin/Applespring about 1 hour from houston

Originally Posted by 2000Limited

Where is all the progress!!!! lol

Man , She moves under her own power. I sold the 700 and got the turbo 400. Its an animal. she needs some tuning, but it moves under its own power.. I'm happy. I over filled the trans (had wrong dipstick) then it blew most back out.. decided to drive it... 2nd is slipping bad.. think I ruined it! /: but even with 2nd slipping I was doing rollin' burnouts all day! It was d@mn fun! Dad said no more though or it wouldn't make it on a trailer lol I'm gonna try to add fluid... see if she will quit slipping. either way I have a bad driveline vibration. think its the trans anyways. dad is retiring before we move he is talking about getting the trans built for me with his money since I have worked so hard on it! but its fun!

[bbbc10]

gotcha that's a few hrs away from all us guys up here in dallas

[Hankster]

I want to head up to dallas and check it all out.

[bbbc10]

more than welcome we go an have meets all the time.....we got some facebook pages too

https://www.facebook.com/groups/LoneStarSquares/

[Hankster]

Ten four man! Good to know!

[Hankster]

I Done some tweaking on fluid.. lol No more slipping. I still have a terrible vibration though. I'm thinking its the torque converter. Because it does it sitting still, and the higher the rpms the worse it gets. But, when I'm going down the road... its even worse. Any input?

[bucannon]

i would guess flywheel or torque converter. once i didn't tighten one of the 3 bolts from the flywheel to torque converter and it had a terrible vibration as well

[ChevDog1]

Originally Posted by Hankster

I Done some tweaking on fluid.. lol No more slipping. I still have a terrible vibration though. I'm thinking its the torque converter. Because it does it sitting still, and the higher the rpms the worse it gets. But, when I'm going down the road... its even worse. Any input?

Did you use an externally balanced flexplate when you installed your 700R4? The 454 is externally balanced, and will have a weight welded to the flexplate, where most small blocks (except 400) have no weight. I had the same problem as you, only in reverse. When I bought my truck, it had a 454 flexplate used on my 250 straight six. Shook bad. Removed the weight and its fine now.

Did you reuse the flexplate from your small block?

[Hankster]

When I bought the 454 it came with a balanced flex-plate. When I had the 700r4 in the truck it didn't shake like this! Thanks for the input!

[TheBlueBomber]

Glad to see she's moving under her own power. You beat me at getting yours running before I did so I give you props. Got any new pictures?

[Hankster]

Originally Posted by TheBlueBomber

Glad to see she's moving under her own power. You beat me at getting yours running before I did so I give you props. Got any new pictures?

Thanks man, sorry for late reply, been moving. We know live in Texas. I got alot of new pictures on my phone. I'll have to get them on here soon. she is also rocking 20s now!

[Hankster]

Here's a pic with the 20s,

[ECU PIRATE]

Originally Posted by Hankster

Here's a pic with the 20s,

Nice!!!!!!!!!!!!!

[Hankster]

Thank ya!

[Hankster]

So here's an update looking back to just over a month ago.

I dropped my 700r4, sold it and bought a turbo 400, and mount, for about the same amount it'd cost me to get my drive-shaft cut to work with the 700r4. Me and dad wrestled it in, got it buttoned up, done the home made flip on the back.. (We had a buddy of our cut the perch pads off, flip them and re-weld them, On my 12 bolt I got to swap in) Me and dad and a buddy worked on that for a while. Got it bolted together, realized that The turbo 400 takes a different yoke. Went to a junk yard the next day, whom said they were out of what I needed, I told them a 4l80e yoke would work and they went and got it. Took it and got it put on, along with new u-joints. Got home and realized again that my drive-shaft is still to long, by just under an inch.. Dad said, wait! Aftermarket flip kits move the rear end back an inch, so we unbolted the rear, flipped it up, and drilled new holes.. set it back down, bolted it up, and realized for the 4th time, That they put in the wrong u-joints! Ughhhh another day of waiting.. Got them swapped, got it in, Drove the truck up the road with open manifolds.. Come back and the right front wheel locked up. Had to get new calipers, pads, and lines.. luckily it didn't ruin my rotor, so I bought all that with my Exhaust money. Well now what? I need exhaust. Here comes my brother to the rescue, he said " I'll pay for your exhaust if you take me on the first ride" Done. no problem. Drove it to the exhaust shop the next day with open manifolds, no tag, no registration, etc. Got exhaust drove it home, and realized that its vibrating bad.. hmm maybe pinion angle? nope... does it sitting still is it missing... yes, got that buttoned up, still vibrating.. still... Like to this day, but we done some tuning and off she went. Me and my brother loaded up. Went up the road smoking the tires.. Rolling burnouts all over the place. I was having fun! Got home, popped hood and tranny flood is everywhere. My d@mn dipstick didn't seal up.. Changed it out with another.. its better but still blows some fluid out, In the mist of all this the guy I got the trans from gave me a steering wheel (Gt Grant) just like the one in the truck my dad built.. That's the truck that got me into all this, that's where it all started for me. Another buddy of mine gave me a extra tilt column he had! Thanks man! Loaded everything up and off to Texas we moved. I got the tilt column in about 2 weeks ago. traded my rallies for 20s, and done some more tuning.. enough talk PICTURE TIME.

[Hankster]

First pic is driving to exhaust shop. Second is the exhaust, and third is for fun.

[Hankster]

The vibration is getting worse and worse, Dad thinks we are going to have to get the trans rebuilt, which sucks!

[Hankster]

Crawled under my truck to tightin my starter, and it feel apart in my hand, /: I put it to good use for a couple months though, And it was a free one from 2fat2fly. Oh, and if anyone is still following my build, please say some kind words.. Thanks!

[naphtali5725]

Originally Posted by Hankster

Crawled under my truck to tightin my starter, and it feel apart in my hand, /: I put it to good use for a couple months though, And it was a free one from 2fat2fly. Oh, and if anyone is still following my build, please say some kind words.. Thanks!

some kind words...

looking good, did you get the vibration issue resolved?

[l92powered77]

keep on truckin !!! coming along nice