HED 69648 Elite headers new - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Alan's Classic · 06-10-2009, 11:02 PM

I bought these headers to try to make fit on my truck, but it just didn't work out. The top flange of the frame rail could be clearanced enough, but the collector hits the lower part of the rail alot. Here is a LINKY to the application list thru Summit. I ground on the collector some, but didn't get into the flange of the pipe (as shown in pic). These list for $319.95 thru Summit. I''ll sale them for $250 shipped to the lower 48. I do accept paypal

scotts62 · 06-10-2009, 11:20 PM

Man those would look good on the 62...

Alan's Classic · 06-10-2009, 11:42 PM

Quote:

Originally Posted by scotts62

Man those would look good on the 62...

They're for sale.

Do you think they would work since your frame is custom? I can measure between my rails if you need me too.

scotts62 · 06-11-2009, 07:41 AM

Yeah i know i have been eyeballing them

Yeah measure inside the frame if you dont mind because im not sure what header will fit and may be in the same boat you were

Alan's Classic · 06-11-2009, 11:21 AM

Quote:

Originally Posted by scotts62

Yeah i know i have been eyeballing them

Yeah measure inside the frame if you dont mind because im not sure what header will fit and may be in the same boat you were

I'll see if I can get a measurement for you tonight.

Alan's Classic · 06-11-2009, 10:38 PM

Scott, I measured between the lower part of the frame even with the front of the tranny pan and it measured 29 5/8". Hope this helps.

cjracing15 · 06-12-2009, 06:21 PM

Alan do you know if these will fit a 86 chevy K-10? Also does it come with all the hardware (bolts,gaskets,etc)? If the answer is yes to both questions then I might just be intrested. Thanks, Jamie

Alan's Classic · 06-12-2009, 07:02 PM

Quote:

Originally Posted by cjracing15

Alan do you know if these will fit a 86 chevy K-10? Also does it come with all the hardware (bolts,gaskets,etc)? If the answer is yes to both questions then I might just be intrested. Thanks, Jamie

Here is a link to the 1986 Chevrolet applications. I will let you determine if they will work or not. And yes it comes complete with gaskets, bolts and collectors. The original box is not sutable for shipping. I will have to round up a box to ship them in.

scotts62 · 06-12-2009, 07:41 PM

Quote:

Originally Posted by Alan's Classic

Scott, I measured between the lower part of the frame even with the front of the tranny pan and it measured 29 5/8". Hope this helps.

Mine frame is 31" so it all should clear just fine. Let me see what i can do, if you still have them. Its no biggie

Alan's Classic · 06-12-2009, 08:29 PM

Quote:

Originally Posted by scotts62

Mine frame is 31" so it all should clear just fine. Let me see what i can do, if you still have them. Its no biggie

It will still be tight for you. I hate to say how much I cut out of the lower section of my rail and still needed more. That's why I stopped where I was.

scotts62 · 06-12-2009, 08:45 PM

Quote:

Originally Posted by Alan's Classic

It will still be tight for you. I hate to say how much I cut out of the lower section of my rail and still needed more. That's why I stopped where I was.

Yeah it might be better to buy a weld-up kit and make them like i was going to that way i can make them clear everything if possible.

Alan's Classic · 06-30-2009, 09:43 PM

ttt

Alan's Classic · 09-18-2009, 10:10 PM

Sad news, I just discovered that these headers are not what they are supposed to be. It looks like I got an old switch-a-roo. I don't know what they are or what they go in other than a SBC.

joe231 · 09-22-2009, 09:16 PM

I hate to say it, but they look like the $129 eBay specials.
Are they stainless?
How much do you want for them?
And do you know how wide they are bolted to the engine?

Alan's Classic · 09-22-2009, 09:38 PM

Quote:

Originally Posted by joe231

I hate to say it, but they look like the $129 eBay specials.
Are they stainless?
How much do you want for them?
And do you know how wide they are bolted to the engine?

I haven't even looked on ebay, but I'm sure your right. I believe they are coated, not 100% sure. I will check tonight when I go out to the shop. I can't give you a correct measurement when bolted to the engine because I can't get them to bolt up completely. The passenger side is almost a perfect fit. I thought about cutting a wedge out of the bottom of each tube at the first bend where it meets the head and pull it in and weld it up and have them coated if they aren't stainless. I'll keep you posted.

joe231 · 09-22-2009, 11:11 PM

Cool,
I am wondering if they will fit my '80
lots of guys run the 88-98 headers on the 73-87 trucks with slight modification to the lower frame.

Alan's Classic · 09-22-2009, 11:22 PM

I didn't make it out to the shop tonight. I'll let you know something when I find out. It's been very hard to get back in the groove. I'll get back in the saddle soon I hope.

I took the carb off my 55 when I got home and I never made it back outside.

joe231 · 09-22-2009, 11:41 PM

No rush on my part

joe231 · 09-22-2009, 11:53 PM

If they are coated...maybe these?
they look a lot alike

Coated header linky

06-10-2009, 11:02 PM	#1
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	HED 69648 Elite headers new I bought these headers to try to make fit on my truck, but it just didn't work out. The top flange of the frame rail could be clearanced enough, but the collector hits the lower part of the rail alot. Here is a LINKY to the application list thru Summit. I ground on the collector some, but didn't get into the flange of the pipe (as shown in pic). These list for $319.95 thru Summit. I''ll sale them for $250 shipped to the lower 48. I do accept paypal __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

06-10-2009, 11:20 PM	#2
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,240	Re: HED 69648 Elite headers new Man those would look good on the 62... __________________ Scott 93 crew cab build Project 62

06-11-2009, 07:41 AM	#4
scotts62 One day... Join Date: Apr 2008 Location: Tuttle, Ok Posts: 9,240	Re: HED 69648 Elite headers new Yeah i know i have been eyeballing them Yeah measure inside the frame if you dont mind because im not sure what header will fit and may be in the same boat you were __________________ Scott 93 crew cab build Project 62

06-11-2009, 10:38 PM	#6
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: HED 69648 Elite headers new Scott, I measured between the lower part of the frame even with the front of the tranny pan and it measured 29 5/8". Hope this helps. __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

06-12-2009, 06:21 PM	#7
cjracing15 Registered User Join Date: Jan 2007 Location: Lexington, TN Posts: 1,427	Re: HED 69648 Elite headers new Alan do you know if these will fit a 86 chevy K-10? Also does it come with all the hardware (bolts,gaskets,etc)? If the answer is yes to both questions then I might just be intrested. Thanks, Jamie __________________ The fleet 94 Chevy 4x4 reg cab 2018 Traverse (wifes car) 1977 SWB stepside 1949 Chevy truck Last edited by cjracing15; 06-12-2009 at 06:24 PM.

06-30-2009, 09:43 PM	#12
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: HED 69648 Elite headers new ttt __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

09-18-2009, 10:10 PM	#13
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: HED 69648 Elite headers new Sad news, I just discovered that these headers are not what they are supposed to be. It looks like I got an old switch-a-roo. I don't know what they are or what they go in other than a SBC. __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

09-22-2009, 09:16 PM	#14
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: HED 69648 Elite headers new I hate to say it, but they look like the $129 eBay specials. Are they stainless? How much do you want for them? And do you know how wide they are bolted to the engine? __________________ *CHEVY ONLY* Last edited by joe231; 09-22-2009 at 09:22 PM.

09-22-2009, 11:11 PM	#16
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: HED 69648 Elite headers new Cool, I am wondering if they will fit my '80 lots of guys run the 88-98 headers on the 73-87 trucks with slight modification to the lower frame. __________________ *CHEVY ONLY*

09-22-2009, 11:22 PM	#17
Alan's Classic 1 thing at a time is progress. Join Date: Jun 2007 Location: Ball Ground GA Posts: 5,511	Re: HED 69648 Elite headers new I didn't make it out to the shop tonight. I'll let you know something when I find out. It's been very hard to get back in the groove. I'll get back in the saddle soon I hope. I took the carb off my 55 when I got home and I never made it back outside. __________________ Alan Philippians 2:14-16 Alan's Classic Facebook page. North Georgia Group Project 1965 Vitamin C-10 1995 GMC Sierra K1500 The "Wrecker"

09-22-2009, 11:41 PM	#18
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: HED 69648 Elite headers new No rush on my part __________________ *CHEVY ONLY*

09-22-2009, 11:53 PM	#19
joe231 Registered User Join Date: Dec 2007 Location: Palmer, Alaska Posts: 13,821	Re: HED 69648 Elite headers new If they are coated...maybe these? they look a lot alike Coated header linky __________________ *CHEVY ONLY* Last edited by joe231; 09-22-2009 at 11:54 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.