The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-31-2020, 12:33 PM   #1
Bridgeman57
Registered User
 
Bridgeman57's Avatar
 
Join Date: Nov 2018
Location: Yuba city, California
Posts: 86
1986 block, 1987 heads- CAM HELP

I bough an engine with TBI and I’ve swapped it to carb. I want to put in a new camshaft but not sure what all I should replace because the cam in the block is setup for TBI. Because the degree would be off center a little. Would the stock cam be alright? And if I do add a cam, would I have to install new lifters, rods, valve springs, timing chain? Or would simply moving the cam timing a few degree be easier then spending roughly $500 more into a ****ty stock engine. Or just leave the cam alone and run it?

Suggestions and advice would be great.
Thanks
Bridgeman57 is offline   Reply With Quote
Old 06-01-2020, 04:55 PM   #2
THI
Active Member
 
THI's Avatar
 
Join Date: Jan 2017
Location: Traverse City, MI
Posts: 168
Re: 1986 block, 1987 heads- CAM HELP

The stock TBI cam is really small - around 179* intake duration @ .050" lift. The old 193* intake/202* exhaust cam used in the 307-400 small blocks is a big improvement and would work with the valve springs. The TBI heads are poor flowing heads so going too big on a cam would not work well. Many have had good luck with an RV cam (204*/214*)
THI is offline   Reply With Quote
Old 06-10-2020, 08:49 PM   #3
MikeB
Senior Member
 
MikeB's Avatar
 
Join Date: Jul 2000
Location: North Texas
Posts: 3,378
Re: 1986 block, 1987 heads- CAM HELP

No reason the TBI cam won't work with a carb. But as mentioned above, it's quite small with an emphasis on low RPM torque. Something like a Summit Racing SUM-K1101 cam & kit would be an improvement, without killing low RPM performance.
https://www.summitracing.com/parts/sum-k1101

Be sure to read everything you can on breaking in a flat tappet cam!

As moderate as it is, a 204/214 cam would be a bit big in a 305 with tall gears, like 2.56 or 2.73.

Edit: Yes, if you install a new cam, you must use new lifters and probably will need a new timing set.
__________________
Mike
1969 C10 LWB -- owned for 34 years. 350/TH350, 3.08 posi, 1st Gen Vintage Air, AAW wiring harness, 5-lug conversion, 1985 spindles and brakes.
1982 C10 SWB -- sold
1981 C10 Silverado LWB -- sold, but wish I still had it!
1969 C10 (not the current one) that I bought in the early 1980s. Paid $1200; sold for $1500 a few years later. Just a hint at the appreciation that was coming.
Retired as a factory automation products salesman.
Worked part-time over the years for an engine builder and a classic car repair shop.
Member here for 23 years! This is the very first car/truck Internet forum I joined. I still used a dial-up modem back then!

Last edited by MikeB; 06-11-2020 at 03:29 AM.
MikeB is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:31 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com