The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-13-2018, 10:46 PM   #1
Sawlog
Registered User
 
Join Date: Jun 2017
Location: Central illinois
Posts: 143
Front end drop

This is my 69 c10. I would like to drop the front end 2in.
A 2in drop front coil spring kit the best way to do this?
Thank you
Attached Images
 
Sawlog is offline   Reply With Quote
Old 06-14-2018, 02:18 AM   #2
68 P.O.S.
Registered User
 
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,659
Re: Front end drop

Drop coil springs will be the cheapest way. If your current springs are old and worn out, its possible you might not notice a difference in height, or the drop springs could even raise it a little. Depends on the condition of your springs. You could also go with drop spindles. Most are a 2 1/2" drop and you can use your stock height springs with them.
__________________
72 C10 lwb fleetside -stock 350/350 combo
68 P.O.S. is offline   Reply With Quote
Old 06-14-2018, 05:28 AM   #3
Boog
laying low
 
Boog's Avatar
 
Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 12,888
Re: Front end drop

Although the truck sits up at about factory height. The best way to lower it is always argued. You can buy 2" drop springs for around $100 or 2 1/2" drop spindles for more $ or you can remove your stock springs and cut off 1 round from the bottom of the spring to get approximately 2" drop. I used a 4 1/2" grinder to cut one coil off mine and bought spindles for about 4 1/2" total front drop. It doesn't affect the spring tension so no worry there. It will align and drive just fine. I strongly advise against heating your springs. You won't be happy with the results.
There are lots of threads here about lowering suspensions. Also we have a suspension forum down below just for all things suspension.
Forum index
http://www.67-72chevytrucks.com/vboard/index.php
__________________
Boog
69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver
primer is finer
91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said.

I stand for the flag and kneel at the cross

Last edited by Boog; 06-14-2018 at 05:42 AM.
Boog is offline   Reply With Quote
Old 06-14-2018, 08:28 AM   #4
jessemthompson
Registered User
 
Join Date: Nov 2011
Location: Williamsburg, VA
Posts: 955
Re: Front end drop

Spindles or springs will work. If you go with springs, buy a new set. They are around the hundred dollar price point. Do NOT cut them. There is a ride quality difference. I know from experience. If you’re gonna do it, do it right. If you go with spindles, upgrade the disc brakes while you’re at it.
jessemthompson is offline   Reply With Quote
Old 06-14-2018, 09:14 AM   #5
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,709
Re: Front end drop

2" coil springs are your only choice if you are keeping the drum brakes. There are no drop spindles available for drums.

If it were my truck I would spend the extra money on converting to disc brakes and use the drop spindles. IME, the drums are completely inadequate for running with modern traffic.

I went with ECE for the drop on the front of my '69. And highly recommend them.
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Old 06-14-2018, 11:38 AM   #6
Sawlog
Registered User
 
Join Date: Jun 2017
Location: Central illinois
Posts: 143
Re: Front end drop

Can I keep my 15" rims with disc brakes?
Sawlog is offline   Reply With Quote
Old 06-14-2018, 12:08 PM   #7
Sawlog
Registered User
 
Join Date: Jun 2017
Location: Central illinois
Posts: 143
Re: Front end drop

Can I keep my 15" rims with disc brakes?
Sawlog is offline   Reply With Quote
Old 06-15-2018, 08:06 AM   #8
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,709
Re: Front end drop

Maybe. If you stay with the 6 lug setup you may need to get a set of wheels from a 70's 4x4 truck which will look the same but have additional clearance for the brake calipers.

I converted to 5 lug when I did my conversion because I wanted more options in aftermarket wheels.
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Old 06-15-2018, 06:54 PM   #9
Robznob11
Registered User
 
Robznob11's Avatar
 
Join Date: Feb 2004
Location: brownfield texas (west texas)
Posts: 1,936
Re: Front end drop

Note: with the drop spindle...you will be limited to @ 3.5 bs on a 15" rim! Wheel weights may hit too...depending on how large they are. And you will likely need to trim the rails off of the lower control arms some. But it's easy with a grinder. It's the better choice for ride and geometry in my .02
__________________
The Ghost 67 short wide full custom. 550 hp LSX, 4l80E, narrowed 9". Body dropped w/air ride!
........................ ___
.........________//__{\_____
,,,,,,,/__(⊙)___//___/__(O)_/

@disciple2.rc 💪instagram💪
LED TAILS
Robznob11 is offline   Reply With Quote
Old 06-15-2018, 07:35 PM   #10
rjs53
Registered User
 
Join Date: Jan 2010
Location: nevada
Posts: 649
Re: Front end drop

I just put the ECE 4/6 drop and discs on my 69. Bolted a set of 15" rallies on with no issues. In my opinion I would cut the springs, if you like the look then eventually if you want you can get a drop kit. Its a 1969 pickup the ride quality ain't going to be that noticeable if any.
__________________
2003 Dodge 2500
1969 C10
2014 Camaro SS/RS/1LE
rjs53 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:34 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com