Custom Belt question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

weedoublewide · 08-11-2019, 02:14 AM

If I'm not running an A/C setup, where do I go or can go to get a custom belt for my application??

kipps · 08-11-2019, 07:25 AM

A gen IV 5.3 vortec engine has a completely separate belt just for the AC compressor. It can be deleted without affecting the rest of the accessory drive.

I thought the same applied to other LS engines. Maybe not.

**mongocanfly** · 08-11-2019, 07:30 AM

All 4 of mine have seperate ac belts

weedoublewide · 08-11-2019, 11:49 AM

If I'm not using power steering, do I still need the pully installed to make the belt work?
Or can the belt be re-routed without the pully and still be fine?

**mongocanfly** · 08-11-2019, 12:33 PM

That may be a diff issue....most I've seen without the psp have the aftermarket accessory drive system...looking at mine I dont see a good way to eliminate the psp with a stock drive setup...the belt comes off the wp and goes around psp and then to alt....theres no direct route from wp to alt without psp...
I know reaper has his setup without psp... but with aftermarket drive on one..

**oldman3** · 08-11-2019, 11:45 PM

This is the set-up my son Mark (reaper71) did on a 49 Dodge with LS, no power steering and no AC, maybe this is what you need...Jim

P.S. Sorry last pic is unclear. Size is 13/16" X 75 5/8" OC...Jim

weedoublewide · 08-14-2019, 08:29 PM

Thats what I thought, I got the 76 inch and it was to big by an inch or two...so I picked up a 72" incher and ill let you know if that works?

Thoughts on why the sizes would be different?

Mines an LS 6.0

Duck1 · 08-15-2019, 02:42 AM

M-10, 1.50 thread, 160 mm, 82 1/2 belt 5060824 (dayco), 900027A pulley. I used and old tensioner pulley., Cut then little nipple off for a bushing and the above parts

LeesTruk · 08-15-2019, 05:25 AM

Not trying to start a controversy here, but after looking at the two belt configurations, I noticed the waterpump spin direction on the Reaper truck is opposite of the normal rotation. Can the pump work in both directions?

**mongocanfly** · 08-15-2019, 07:31 AM

its the same lee

LeesTruk · 08-15-2019, 11:17 AM

Yep, you're right. Took a little while to get my head around it. At first glimpse, it looked, well, just wrong

kipps · 08-17-2019, 08:31 PM

Any pulley that contacts the ribbed side of the belt is turning the same direction as the crank pulley.

Any pulley that is operated by the smooth side is turning the opposite direction.

08-11-2019, 02:14 AM	#1
weedoublewide Registered User Join Date: Apr 2016 Location: Rowlett, Tx Posts: 127	Custom Belt question If I'm not running an A/C setup, where do I go or can go to get a custom belt for my application??

08-11-2019, 07:25 AM	#2
kipps Registered User Join Date: Jul 2014 Location: North-central Virginia Posts: 1,099	Re: Custom Belt question A gen IV 5.3 vortec engine has a completely separate belt just for the AC compressor. It can be deleted without affecting the rest of the accessory drive. I thought the same applied to other LS engines. Maybe not. __________________ 1987 C6P V20 truck, 2010 LMG 5.3, AFM delete, 2010 Camaro exhaust manifolds, 1997 nv4500, 1991 np241c, hydroboost, 2005 14bff axle & driveshaft, drop-n-lock gooseneck, 4.10 gears, stock suspension, rims, and tires. Still a work in progress. Any questions or suggestions are welcome!

08-11-2019, 07:30 AM	#3
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,579	Re: Custom Belt question All 4 of mine have seperate ac belts __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

08-11-2019, 11:49 AM	#4
weedoublewide Registered User Join Date: Apr 2016 Location: Rowlett, Tx Posts: 127	Re: Custom Belt question If I'm not using power steering, do I still need the pully installed to make the belt work? Or can the belt be re-routed without the pully and still be fine?

08-11-2019, 12:33 PM	#5
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,579	Re: Custom Belt question That may be a diff issue....most I've seen without the psp have the aftermarket accessory drive system...looking at mine I dont see a good way to eliminate the psp with a stock drive setup...the belt comes off the wp and goes around psp and then to alt....theres no direct route from wp to alt without psp... I know reaper has his setup without psp... but with aftermarket drive on one.. __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver Last edited by mongocanfly; 08-14-2019 at 11:19 PM.

08-11-2019, 11:45 PM	#6
oldman3 Senior Member Join Date: Mar 2011 Location: West Plains, Missouri Posts: 7,553	Re: Custom Belt question This is the set-up my son Mark (reaper71) did on a 49 Dodge with LS, no power steering and no AC, maybe this is what you need...Jim P.S. Sorry last pic is unclear. Size is 13/16" X 75 5/8" OC...Jim Attached Images __________________ my build thread: http://67-72chevytrucks.com/vboard/s...d.php?t=459839 Jimbo's long bed step build:http://67-72chevytrucks.com/vboard/s...t=464626<br /> Last edited by oldman3; 08-11-2019 at 11:58 PM.

08-14-2019, 08:29 PM	#7
weedoublewide Registered User Join Date: Apr 2016 Location: Rowlett, Tx Posts: 127	Re: Custom Belt question Thats what I thought, I got the 76 inch and it was to big by an inch or two...so I picked up a 72" incher and ill let you know if that works? Thoughts on why the sizes would be different? Mines an LS 6.0

08-15-2019, 02:42 AM	#8
Duck1 Registered User Join Date: Dec 2018 Location: San Bernardino Posts: 71	Re: Custom Belt question M-10, 1.50 thread, 160 mm, 82 1/2 belt 5060824 (dayco), 900027A pulley. I used and old tensioner pulley., Cut then little nipple off for a bushing and the above parts Attached Images

08-15-2019, 05:25 AM	#9
LeesTruk Registered User Join Date: Mar 2015 Location: Manchester, CT Posts: 429	Re: Custom Belt question Not trying to start a controversy here, but after looking at the two belt configurations, I noticed the waterpump spin direction on the Reaper truck is opposite of the normal rotation. Can the pump work in both directions?

08-15-2019, 07:31 AM	#10
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,579	Re: Custom Belt question its the same lee Attached Images __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

08-15-2019, 11:17 AM	#11
LeesTruk Registered User Join Date: Mar 2015 Location: Manchester, CT Posts: 429	Re: Custom Belt question Yep, you're right. Took a little while to get my head around it. At first glimpse, it looked, well, just wrong Last edited by LeesTruk; 08-15-2019 at 11:31 AM.

08-17-2019, 08:31 PM	#12
kipps Registered User Join Date: Jul 2014 Location: North-central Virginia Posts: 1,099	Re: Custom Belt question Any pulley that contacts the ribbed side of the belt is turning the same direction as the crank pulley. Any pulley that is operated by the smooth side is turning the opposite direction. __________________ 1987 C6P V20 truck, 2010 LMG 5.3, AFM delete, 2010 Camaro exhaust manifolds, 1997 nv4500, 1991 np241c, hydroboost, 2005 14bff axle & driveshaft, drop-n-lock gooseneck, 4.10 gears, stock suspension, rims, and tires. Still a work in progress. Any questions or suggestions are welcome!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.