The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > Diesel Conversions

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-16-2015, 12:44 AM   #1
87Skier
Registered User
 
87Skier's Avatar
 
Join Date: Mar 2014
Location: Corvallis, OR
Posts: 711
3.9L Cummins/Isuzu diesel swap in 89 Suburban

I've got an 89 Suburban (picked up as a project vehicle, just unsure of the project) that has a motor that runs but I suspect will have bottom end issues in the next couple years. Sounds like a rod knock on startup, but could be anything. Already has top end issues.

Moving passed that, I thought this would make a good candidate for a diesel swap. I know the 5.9L Cummins are incredibly long and hard to fit in any vehicle and since this came underpowered from the factory, I thought putting the smaller diesel in would be a good compromise. I've been looking at parts and so far it isn't adding up.

V2500 Suburban (Square body style)
350 TBI engine
Turbo 400 (3 speed trans)
NP231 (chain driven, right hand drop) transfer case
4.10:1 front and rear gearing
235/85r16 tires

Currently at 60mph, the engine is at 2600 rpm. I am shooting for around 1500 rpm at 60mph. Even if I swapped in an OD transmission that still puts the engine close to 1850 rpm. I think it is still on the high side.

What are your thoughts on this? Which transmission should be used? 700r4? I've heard that 4bt's are a lot more expensive but could save you money in the long run since Isuzu parts are more expensive.

I would like to avoid changing out the gearing if possible.
__________________
1972 GMC Jimmy Custom 4.8L (L20)/6L90E/NP205
1989 Chevy Suburban V2500 350/Turbo 400/4.11 gears
1996 Chevy Suburban K1500 350/4L60E
87Skier is offline   Reply With Quote
Old 09-17-2015, 09:40 PM   #2
79c25
Registered User
 
79c25's Avatar
 
Join Date: Jul 2014
Location: Lovell WY
Posts: 93
Re: 3.9L Cummins/Isuzu diesel swap in 89 Suburban

4bt, nv4500, np205 passenger drop. Should put you around 1800 rpm in 5th going 60. I know in my old 12 valve I got about 20 mpg going 65 everywhere, I think that the 4bt will do a little better. But, that's if you wanted to go with a manual. As far as an auto the 4L80E should be right about the same. But I'm interested in this swap as I'm looking to do the same in my 84 K5. As a side note the 12 valve does fit in the engine bay but I wouldn't use a 4L80E behind a 12 valve personally. That's my $0.02.
__________________
1979 GMC Sierra Grande Crew Cab C25, 454/TH400/4.10-Project truck/ DD
1985 Chevy K5 Blazer 700r4/4.10/8 lug- in search of new engine
1993 GMC Sierra K1500 4L60E
2007 Suzuki Forenza- her DD and the family vehicle
79c25 is offline   Reply With Quote
Old 09-24-2015, 07:55 AM   #3
burnin oil
Registered User
 
Join Date: Jan 2013
Location: Eastern TN
Posts: 1,919
Re: 3.9L Cummins/Isuzu diesel swap in 89 Suburban

You will want a little more RPM to keep that 3.9 happy. Basically it will be lugging around without any boost while trying to move that brick. My 95 Dodge spun 2600 RPM on the interstate and the rest of my commute was like going to a rock concert. She still knocked out mid 18s for milage in a 4x4. My dads 24v 5.9 gets just under 20mpg every tank, unless towing, running 4.10s and a 6spd in a 4x4. Don't let the RPM scare you to much. Just make sure the pumps gov springs are addressed so it doesn't go into defuel.
burnin oil is offline   Reply With Quote
Old 09-29-2015, 04:11 PM   #4
87Skier
Registered User
 
87Skier's Avatar
 
Join Date: Mar 2014
Location: Corvallis, OR
Posts: 711
Re: 3.9L Cummins/Isuzu diesel swap in 89 Suburban

Quote:
Originally Posted by 79c25 View Post
4bt, nv4500, np205 passenger drop. Should put you around 1800 rpm in 5th going 60. I know in my old 12 valve I got about 20 mpg going 65 everywhere, I think that the 4bt will do a little better. But, that's if you wanted to go with a manual. As far as an auto the 4L80E should be right about the same. But I'm interested in this swap as I'm looking to do the same in my 84 K5. As a side note the 12 valve does fit in the engine bay but I wouldn't use a 4L80E behind a 12 valve personally. That's my $0.02.
Why not use the 4L80? Personal preference? I was thinking of using it because of the cost of finding a manual transmission and having to convert my auto to manual. I really like driving manual transmissions though.
__________________
1972 GMC Jimmy Custom 4.8L (L20)/6L90E/NP205
1989 Chevy Suburban V2500 350/Turbo 400/4.11 gears
1996 Chevy Suburban K1500 350/4L60E
87Skier is offline   Reply With Quote
Old 09-29-2015, 04:19 PM   #5
87Skier
Registered User
 
87Skier's Avatar
 
Join Date: Mar 2014
Location: Corvallis, OR
Posts: 711
Re: 3.9L Cummins/Isuzu diesel swap in 89 Suburban

Quote:
Originally Posted by burnin oil View Post
You will want a little more RPM to keep that 3.9 happy. Basically it will be lugging around without any boost while trying to move that brick. My 95 Dodge spun 2600 RPM on the interstate and the rest of my commute was like going to a rock concert. She still knocked out mid 18s for milage in a 4x4. My dads 24v 5.9 gets just under 20mpg every tank, unless towing, running 4.10s and a 6spd in a 4x4. Don't let the RPM scare you to much. Just make sure the pumps gov springs are addressed so it doesn't go into defuel.
I didn't know that the 3.9L wanted more rpm. I figured it was pretty close to the 5.9L. I'm familiar with the basic process of waking up these motors, but I don't have wrench time on them though.

Also, is there any reason to avoid the Isuzu diesel? Would it cost me more in the long run? I think I can pickup the Isuzu for 1000 but I can't seem to find a Cummins for less than 2000.

And lastly, should I consider just swapping over to a 5.9L instead of the 3.9L?
__________________
1972 GMC Jimmy Custom 4.8L (L20)/6L90E/NP205
1989 Chevy Suburban V2500 350/Turbo 400/4.11 gears
1996 Chevy Suburban K1500 350/4L60E
87Skier is offline   Reply With Quote
Old 10-04-2015, 08:33 AM   #6
79c25
Registered User
 
79c25's Avatar
 
Join Date: Jul 2014
Location: Lovell WY
Posts: 93
Re: 3.9L Cummins/Isuzu diesel swap in 89 Suburban

Quote:
Originally Posted by 87Skier View Post
Why not use the 4L80? Personal preference? I was thinking of using it because of the cost of finding a manual transmission and having to convert my auto to manual. I really like driving manual transmissions though.
I don't feel that it's a reliable choice behind a 12 valve UNLESS you get it built to handle it. First generation 12s put out 400 lb ft of torque and if I remember right the 2nd generation put out 450+, the 4L80E is rated for ~350 lb ft stock. It might last a while if you are extremely nice to it though.it should do ok behind a 3.9, but once again,you have to be easy on it unless you get a built one.
__________________
1979 GMC Sierra Grande Crew Cab C25, 454/TH400/4.10-Project truck/ DD
1985 Chevy K5 Blazer 700r4/4.10/8 lug- in search of new engine
1993 GMC Sierra K1500 4L60E
2007 Suzuki Forenza- her DD and the family vehicle
79c25 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:02 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com