Normy71 - Page 3 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Normy71 · 12-19-2009, 10:39 PM

No not yet but I will be looking into that is the future

Normy71 · 12-19-2009, 10:41 PM

Try this
www.performanceparts4less.com

Normy71 · 12-28-2009, 05:49 PM

Found a little time over Xmas I cut the rear frame and dressed up some welds.
Also founds some pipe for cut outs.

PHAT TONY · 12-30-2009, 02:18 AM

I don't think I've seen this done on a leaf spring truck, you seem to be short on bumper bracket room. Hmmm.

*2tons of fun* · 12-30-2009, 05:16 AM

why did you cut and section under the cab?

Rokcrln · 12-30-2009, 12:13 PM

Quote:

Originally Posted by PHAT TONY

I don't think I've seen this done on a leaf spring truck, you seem to be short on bumper bracket room. Hmmm.

LOWBUK is a leaf truck and all worked out just fine! I just don't remember what I had to do but I think it was just a matter of drilling new holes in the rails.

Progress is looking good!

Kevin
LFD Inc.

Normy71 · 12-30-2009, 12:30 PM

Thanks Rokcrin!
Coming from you means a lot to a novice like me.

Normy71 · 01-06-2010, 10:21 PM

I sand blasted my front spring and painting them with KBS .
Also removed my C notch and painted it and the frame.

VA72C10 · 01-13-2010, 12:42 AM

Looking good. Nice work!

chevy88 · 01-13-2010, 07:28 PM

So will you be able to put a bumper on your truck or are you going to roll pan, cause I will be cutting mine in the same place as I have leaf springs also. I'm just curious as I want bumper but looks like
i may need to go roll pan.

Normy71 · 01-18-2010, 10:58 PM

Built my engine adapter plates out of 3/8 steel a little over kill.
Used POL engine mount

Normy71 · 01-18-2010, 11:00 PM

Transmission is going to be next after a nice coat of paint!

mcbassin · 01-19-2010, 12:44 AM

What tranny are you running behind the LS engine?

Normy71 · 01-19-2010, 09:21 AM

It's 4L60E out of a 2005 it has 30k miles on it!
I have a new filter and pan gasket to put in before I put it behind the 5.3.

Normy71 · 01-28-2010, 04:19 PM

Took the trans pan off and all looks good!
Put in a new filter and gasket.

Normy71 · 01-28-2010, 04:23 PM

Time to start putting the front end back together.
I need to order a few more parts, never ending trips to the part store!
But worth it.

mcbassin · 01-28-2010, 10:49 PM

Looking great!

VA72C10 · 01-28-2010, 10:54 PM

Looking very good!

chevy88 · 02-02-2010, 10:39 PM

What kind of paint are you using on your front suspension parts?

Normy71 · 02-02-2010, 10:48 PM

It's Called KBS rust paint
Same type of paint over rust as POR 15
It is one great product.

chevy88 · 02-02-2010, 11:03 PM

What store carry's that as I want to put something on the underside of my bed where I welded to seal and keep out rust?

Normy71 · 02-08-2010, 10:27 PM

Picked up a set of seats today.
I'm a long way from needing them,but you need to have a plan.

*Puropedo* · 02-09-2010, 12:06 AM

Looking good!.. Are you going to use the stock exhaust manifolds that came with your LS engine? Is that a trucks 5.3?

Normy71 · 02-09-2010, 08:16 AM

Yes it is a 5.3 all aluminums L33
I would like a set of headers but not sure if they are in the budget?
If that word (budget) can be used in a frame up build.

*Puropedo* · 02-09-2010, 11:59 AM

Judging from your pics it looks like you are going to have to do some frame trimming in order to fit the stock manifolds, Ive been looking at some headers for my application but, man they are pricey (sometimes more than what Ive paid for a complete drivetrain) they sure look nice though...

12-19-2009, 10:39 PM	#51
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 No not yet but I will be looking into that is the future __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

12-19-2009, 10:41 PM	#52
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Try this www.performanceparts4less.com __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

12-28-2009, 05:49 PM	#53
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Found a little time over Xmas I cut the rear frame and dressed up some welds. Also founds some pipe for cut outs. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158 Last edited by Normy71; 12-28-2009 at 05:52 PM.

12-30-2009, 02:18 AM	#54
PHAT TONY Registered User Join Date: Aug 2008 Location: Red Deer ab canada Posts: 1,250	Re: Normy71 I don't think I've seen this done on a leaf spring truck, you seem to be short on bumper bracket room. Hmmm. __________________ 1972 factory 2 Wheel Drive Blazer-Sold 1972 K10 4X4-Sold 1971 Chevrolet Cheyenne/10-Sold 1970 Chevrolet C/10-Sold 1968 GMC 4X4-Project 1968 Chevrolet C/10 Pro Street 1970 GMC 3/4 Ton-Parts 1997 2WD 2DR Yukon-Sweet http://67-72chevytrucks.com/vboard/s...d.php?t=335664

12-30-2009, 05:16 AM	#55
2tons of fun Account Suspended Join Date: Jan 2009 Location: galt ca, Posts: 749	Re: Normy71 why did you cut and section under the cab?

12-30-2009, 12:30 PM	#57
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Thanks Rokcrin! Coming from you means a lot to a novice like me. __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-06-2010, 10:21 PM	#58
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 I sand blasted my front spring and painting them with KBS . Also removed my C notch and painted it and the frame. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-13-2010, 12:42 AM	#59
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Normy71 Looking good. Nice work! __________________ Looking for a 67-72 swb or blazer project in or around VA.

01-13-2010, 07:28 PM	#60
chevy88 Registered User Join Date: May 2007 Location: Southern, Saskatchewan Posts: 640	Re: Normy71 So will you be able to put a bumper on your truck or are you going to roll pan, cause I will be cutting mine in the same place as I have leaf springs also. I'm just curious as I want bumper but looks like i may need to go roll pan. __________________ Kerry My build thread. http://67-72chevytrucks.com/vboard/s....php?p=3657823 1971 Chev SWB with 68 nose, 6.2 diesel th350, and 3.73 rear gears 1988 Chev Extendacab 2010 Honda VT1300CS Sabre 2005 Buick Rendezvous wife's ride Last edited by chevy88; 01-14-2010 at 03:04 PM.

01-18-2010, 10:58 PM	#61
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Built my engine adapter plates out of 3/8 steel a little over kill. Used POL engine mount Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-18-2010, 11:00 PM	#62
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Transmission is going to be next after a nice coat of paint! Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-19-2010, 12:44 AM	#63
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Normy71 What tranny are you running behind the LS engine? __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

01-19-2010, 09:21 AM	#64
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 It's 4L60E out of a 2005 it has 30k miles on it! I have a new filter and pan gasket to put in before I put it behind the 5.3. __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-28-2010, 04:19 PM	#65
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Took the trans pan off and all looks good! Put in a new filter and gasket. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

01-28-2010, 04:23 PM	#66
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Time to start putting the front end back together. I need to order a few more parts, never ending trips to the part store! But worth it. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158



Register or Log In To remove these advertisements.

01-28-2010, 10:49 PM	#67
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Normy71 Looking great! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

01-28-2010, 10:54 PM	#68
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Normy71 Looking very good! __________________ Looking for a 67-72 swb or blazer project in or around VA.

02-02-2010, 10:39 PM	#69
chevy88 Registered User Join Date: May 2007 Location: Southern, Saskatchewan Posts: 640	Re: Normy71 What kind of paint are you using on your front suspension parts? __________________ Kerry My build thread. http://67-72chevytrucks.com/vboard/s....php?p=3657823 1971 Chev SWB with 68 nose, 6.2 diesel th350, and 3.73 rear gears 1988 Chev Extendacab 2010 Honda VT1300CS Sabre 2005 Buick Rendezvous wife's ride Last edited by chevy88; 02-02-2010 at 10:39 PM.

02-02-2010, 10:48 PM	#70
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 It's Called KBS rust paint Same type of paint over rust as POR 15 It is one great product. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

02-02-2010, 11:03 PM	#71
chevy88 Registered User Join Date: May 2007 Location: Southern, Saskatchewan Posts: 640	Re: Normy71 What store carry's that as I want to put something on the underside of my bed where I welded to seal and keep out rust? __________________ Kerry My build thread. http://67-72chevytrucks.com/vboard/s....php?p=3657823 1971 Chev SWB with 68 nose, 6.2 diesel th350, and 3.73 rear gears 1988 Chev Extendacab 2010 Honda VT1300CS Sabre 2005 Buick Rendezvous wife's ride

02-08-2010, 10:27 PM	#72
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Picked up a set of seats today. I'm a long way from needing them,but you need to have a plan. Attached Images __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

02-09-2010, 12:06 AM	#73
Puropedo Account Suspended Join Date: Nov 2008 Location: Prunedale California Posts: 782	Re: Normy71 Looking good!.. Are you going to use the stock exhaust manifolds that came with your LS engine? Is that a trucks 5.3?

02-09-2010, 08:16 AM	#74
Normy71 Registered User Join Date: Apr 2009 Location: Saskatchewan, Canada Posts: 236	Re: Normy71 Yes it is a 5.3 all aluminums L33 I would like a set of headers but not sure if they are in the budget? If that word (budget) can be used in a frame up build. __________________ Rolled the dice and lost!! Check Out my 71 build http://67-72chevytrucks.com/vboard/s...d.php?t=375158

02-09-2010, 11:59 AM	#75
Puropedo Account Suspended Join Date: Nov 2008 Location: Prunedale California Posts: 782	Re: Normy71 Judging from your pics it looks like you are going to have to do some frame trimming in order to fit the stock manifolds, Ive been looking at some headers for my application but, man they are pricey (sometimes more than what Ive paid for a complete drivetrain) they sure look nice though...

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.