Whatta you think of my dash? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

c10addict · 10-11-2007, 10:26 PM

So I took some opinions and thought the dash would look much cleaner with the ignition,heater controls and lighter removed from under the new cluster SOOOO I welded it all up. (see new pics) I moved the Ignition switch to the glove box door covering the factory cluster opening and drilled for the headlamp and wiper switches in the lower left corner. I still need to remove and fill the latch... I am in the middle of figuring out the heater controls and should turn out cool if I can pull my idea off.. I wish I would have known I was going to smooth the entire center from the start, I would have cut all the old stuff out and put 1 piece in!

Thanks for all your feedback..

I am currently building a 67 shop truck... I want to go with an old school custom look.. So far I know it will be flat gold with a gloss black roof with some flake in it.. I am going to run black steelies with dog dishes. I will be running a big block with an auto, looking for a good 700r4 (got lots of old school engine candy to complete the look

) . I already have the airride kit and we are getting ready to start on the chassis.. I wanted a custom dash with an old school flair so I dreamed this up and started cutting and welding... I will be putting a glove box door over the stock cluster location and notching it for the column.. I have a 56 chevy 210 steering wheel I am going to use to carry on the "V" look.... I plan on getting both glove box doors striped with some von dutch style pinstriping... What do you think ???

samwise68 · 10-11-2007, 10:49 PM

that...is some awesome fab work!

might be a pain to see the speedo...?

but. even if it is. that is an absolute *****in' job of grafting. wow.

-Sam.

72armyswbtruck · 10-11-2007, 11:11 PM

That's pretty neat, I have seen it done before but hey that is some good fab work. Thansk for the pics.

724x4a/cchevy · 10-11-2007, 11:28 PM

thats awsome. Is the cluster out of a 56? kinda somewhat looks similar to a 55 chevy. I know its not, but..
Justin

matthufham · 10-11-2007, 11:51 PM

it fits perfectly!

**special-K** · 10-12-2007, 07:13 AM

I like it.Makes me wanna see heater controls from a `50s car.I`m taking a simular approach with my`67 GMC project.Not sure about the dash,yet.I am thinking glovebox door for cluster using vintage gauges in a different layout.Not going past the mid-60s with any styling.

70GMCer · 10-12-2007, 07:15 AM

My opinion is, it's different, but that it would be awkward driving and looking to the right. Besides, I think it would be better suited installed in the same area as the original dash. To me, it just doesn't look right with the heater controls right below. I'm not bashing your work, this is just my thoughts, as you asked.

c10addict · 10-12-2007, 07:29 AM

The cluster is out of a 57 chevy truck.. As far as seeing the speedo its not bad.. Its big and no different than glancing at the radio station but MUCH bigger than a radio display... Plus who needs a speedo as long as the shift light is not on your ok!!

I am trying to figure out a new set of heater controls, need to make a trip to the bone yard... I originally wanted to put something in the stock location but there is not much space due to where the column lives... I already did the autometer thing in my 68 and wanted to do something different...

jamis · 10-12-2007, 07:34 AM

Great idea and well executed

70GMCer · 10-12-2007, 07:45 AM

I see your point on the column being in the way. It might look pretty cool with a different type heater control. I thought I saw where someone put in a 1959 Chevy Impala dash on these trucks. Maybe they have a different heater setup that you could get an idea from.

earl87gta · 10-12-2007, 07:56 AM

Are you going to use a steering colume with a key in it ? I thnik it would look way better if you got rid of the heater controls and the lighter too. its to busy around the speedo and takes a way from the work you did. but it does look good.

ABN82MP · 10-12-2007, 08:27 AM

Looks cool, but...

My wife's Saturn ION had the speedo in the center of the dash. It was a freekin PITA to see it. It was supposed to be a safety feature, but I fealt like I always had to search for the speedo then see how fast I was going causing me to have my eyes off the road longer.

Of course...I'm guessing this is going to be a cruiser, not a DD so that wont matter

c10addict · 10-12-2007, 08:28 AM

I have a stock tilt column I am using but I might move the ignition switch or fill around it and move it forward so there is only a small hole to put the stem of the key in.. .. I am going to put the headlamp switch and wiper switch under the dash.. I thought about putting the heater controls in the glove box since I rarely even use them in my 68... You know looks over functionality!! Lol!!

67ChevyRedneck · 10-12-2007, 10:54 AM

Quote:

Originally Posted by 724x4a/cchevy

thats awsome. Is the cluster out of a 56? kinda somewhat looks similar to a 55 chevy. I know its not, but..
Justin

55-59 chevy truck. They are a cool looking cluster.

Out of curiosity, would that cluster have fit in the stock location cut into a glovebox door? Or was the column in the way... I have a 58 cluster....

c10addict · 10-12-2007, 11:06 AM

No it would not fit above the column unless you cut in to the dash board... If I was going to go that far I would have used a 57 chevy car or 59/60 impala dash... this one was easy to pull off!

shifty · 10-12-2007, 11:11 AM

why in the center of the dash, though? seems a little coutner-intuitive as far as functionality goes.

72 cheyenne pdx · 10-12-2007, 11:27 AM

I think it is a great look. If I remember right the Old and New Mini's have the speedo in the middle of the dash. I don't think it will be too hard to look a little to the right to see the speed. Are you going to have heat/AC controls? If so, where? Are you leaving the original cluster area smooth like in the picture or are you going to do something in that area. Anyways, great look. You had a vision and went with it. That is why I love this site. Everyone here is willing to give out their ideas and help the less experienced people to make their visions possible.

c10addict · 10-12-2007, 11:31 AM

At this stage of the game I am leaving it smooth... I looked at putting the airride controls and some other stuff there but it just doesnt look right... I am going to put the radio and other stuff in the center console..

*Billla* · 10-12-2007, 11:31 AM

Quote:

Originally Posted by c10addict

I will be putting a glove box door over the stock cluster location and notching it for the column.

Cool to see something very custom and very nice work grafting it in!

I'm a little hinky on glove box where the cluster is today - I'd think it'd be tough to get into and the notch would look kinda funny when it was closed. Do you have a sketch of how this is all going to come together?

c10addict · 10-12-2007, 11:43 AM

no sketch... only in my head... THe glove box door is only used as a filler, not functional, welding the latch hole smooth... I am probably going to get some aluminum stock and make some polished trim accents

boundstaffpress · 10-12-2007, 05:12 PM

That is sharp!

Jeep had their speedo in the middle for years. Old VW's did, Lots of Model A and T customs do. I think you did a great job.

earl87gta · 10-12-2007, 05:13 PM

I was on a web site not long ago that had a LCD TV that was set up to be all your gages. At the time I tought what would you do with that but now after seeing yours Im thinking you could put it in a glove box door and have only it plus you could watch the news while your driving.

corn · 10-12-2007, 06:57 PM

Perfect location? Who gives a crap! Its KEWL! Thats all that matters. Please keep us updated on your shop truck!

1969k10stepside · 10-12-2007, 07:01 PM

Nice mod!

**special-K** · 10-13-2007, 08:13 AM

The speedo in the center just takes a change in old habits.Like said,you just glance at it.It`s not like reaching over and tuning a radio with tiny numbers on it.Many high performance world-class sports cars place the speedo in the center.You don`t have to look through the steering wheel.
I`m sure another heater control can be adapted somewhere.

10-11-2007, 10:26 PM	#1
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	So now Whatta you think of my dash REVISED? So I took some opinions and thought the dash would look much cleaner with the ignition,heater controls and lighter removed from under the new cluster SOOOO I welded it all up. (see new pics) I moved the Ignition switch to the glove box door covering the factory cluster opening and drilled for the headlamp and wiper switches in the lower left corner. I still need to remove and fill the latch... I am in the middle of figuring out the heater controls and should turn out cool if I can pull my idea off.. I wish I would have known I was going to smooth the entire center from the start, I would have cut all the old stuff out and put 1 piece in! Thanks for all your feedback.. I am currently building a 67 shop truck... I want to go with an old school custom look.. So far I know it will be flat gold with a gloss black roof with some flake in it.. I am going to run black steelies with dog dishes. I will be running a big block with an auto, looking for a good 700r4 (got lots of old school engine candy to complete the look) . I already have the airride kit and we are getting ready to start on the chassis.. I wanted a custom dash with an old school flair so I dreamed this up and started cutting and welding... I will be putting a glove box door over the stock cluster location and notching it for the column.. I have a 56 chevy 210 steering wheel I am going to use to carry on the "V" look.... I plan on getting both glove box doors striped with some von dutch style pinstriping... What do you think ??? Attached Images __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile Last edited by c10addict; 10-15-2007 at 09:26 PM. Reason: spelling error

10-11-2007, 11:11 PM	#3
72armyswbtruck Registered User Join Date: Feb 2004 Location: Idaho Posts: 4,034	Re: Whatta you think of my dash? That's pretty neat, I have seen it done before but hey that is some good fab work. Thansk for the pics. __________________ "Remember, They can Kill You, but they can't eat You, That's against the law!!!!!!!!!"

10-11-2007, 11:28 PM	#4
724x4a/cchevy Self-proclaimed LED man Join Date: Nov 2003 Location: Harrisburg, Missouri Posts: 1,021	Re: Whatta you think of my dash? thats awsome. Is the cluster out of a 56? kinda somewhat looks similar to a 55 chevy. I know its not, but.. Justin __________________ My LED Website My Photobucket Album of LED's Ask me about hand-made custom L.E.D brake and reverse lights. <- LINK I also do LED: -Third Brake/Cargo -Brake (truck and burb) -Reverse (truck and burb) -67-68 Front Turn Signals -69-70 Front Turn Signals -71-72 Front Turn Signals -GMC Front Turn Signals I can also do custom lights for other vehicles....i did a set for a AMC Gremlin once Norwood Survivor

10-11-2007, 11:51 PM	#5
matthufham Registered User Join Date: Feb 2005 Location: Carl Junction, Missouri Posts: 2,061	Re: Whatta you think of my dash? it fits perfectly!

10-12-2007, 07:13 AM	#6
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: Whatta you think of my dash? I like it.Makes me wanna see heater controls from a `50s car.I`m taking a simular approach with my`67 GMC project.Not sure about the dash,yet.I am thinking glovebox door for cluster using vintage gauges in a different layout.Not going past the mid-60s with any styling. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 10-12-2007 at 07:15 AM.

10-12-2007, 07:15 AM	#7
70GMCer Senior Member Join Date: Apr 2005 Location: Joppa, Maryland Posts: 4,408	Re: Whatta you think of my dash? My opinion is, it's different, but that it would be awkward driving and looking to the right. Besides, I think it would be better suited installed in the same area as the original dash. To me, it just doesn't look right with the heater controls right below. I'm not bashing your work, this is just my thoughts, as you asked. __________________ 1997 GMC Sierra Ext 1965 Mustang Last edited by 70GMCer; 10-12-2007 at 07:16 AM.

10-12-2007, 07:29 AM	#8
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	Re: Whatta you think of my dash? The cluster is out of a 57 chevy truck.. As far as seeing the speedo its not bad.. Its big and no different than glancing at the radio station but MUCH bigger than a radio display... Plus who needs a speedo as long as the shift light is not on your ok!! I am trying to figure out a new set of heater controls, need to make a trip to the bone yard... I originally wanted to put something in the stock location but there is not much space due to where the column lives... I already did the autometer thing in my 68 and wanted to do something different... Attached Images __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile

10-12-2007, 07:34 AM	#9
jamis F.A.S.T. president Join Date: Sep 2003 Location: Florida Posts: 1,883	Re: Whatta you think of my dash? Great idea and well executed __________________ F.A.S.T. President and Founder Fabricators for the Advancement of Sawsall Technology "A fear of the Sawsall is a sign of retarded sexual and emotional maturity." ~Sigmund Freud, "General Introduction to Psychoanalysis"

10-12-2007, 07:45 AM	#10
70GMCer Senior Member Join Date: Apr 2005 Location: Joppa, Maryland Posts: 4,408	Re: Whatta you think of my dash? I see your point on the column being in the way. It might look pretty cool with a different type heater control. I thought I saw where someone put in a 1959 Chevy Impala dash on these trucks. Maybe they have a different heater setup that you could get an idea from. __________________ 1997 GMC Sierra Ext 1965 Mustang

10-12-2007, 07:56 AM	#11
earl87gta Senior Member Join Date: Dec 2003 Location: Kingsport TN Posts: 4,641	Re: Whatta you think of my dash? Are you going to use a steering colume with a key in it ? I thnik it would look way better if you got rid of the heater controls and the lighter too. its to busy around the speedo and takes a way from the work you did. but it does look good. __________________ Earl 68 2500 4x4 GMC Burb

10-12-2007, 08:27 AM	#12
ABN82MP Registered User Join Date: Sep 2007 Location: Wooster, OH Posts: 46	Re: Whatta you think of my dash? Looks cool, but... My wife's Saturn ION had the speedo in the center of the dash. It was a freekin PITA to see it. It was supposed to be a safety feature, but I fealt like I always had to search for the speedo then see how fast I was going causing me to have my eyes off the road longer. Of course...I'm guessing this is going to be a cruiser, not a DD so that wont matter

10-12-2007, 08:28 AM	#13
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	Re: Whatta you think of my dash? I have a stock tilt column I am using but I might move the ignition switch or fill around it and move it forward so there is only a small hole to put the stem of the key in.. .. I am going to put the headlamp switch and wiper switch under the dash.. I thought about putting the heater controls in the glove box since I rarely even use them in my 68... You know looks over functionality!! Lol!! __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile

10-12-2007, 11:06 AM	#15
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	Re: Whatta you think of my dash? No it would not fit above the column unless you cut in to the dash board... If I was going to go that far I would have used a 57 chevy car or 59/60 impala dash... this one was easy to pull off! __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile

10-12-2007, 11:11 AM	#16
shifty Questionable Join Date: Mar 2005 Location: Atlanta Posts: 13,376	Re: Whatta you think of my dash? why in the center of the dash, though? seems a little coutner-intuitive as far as functionality goes. __________________ If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM.

10-12-2007, 11:27 AM	#17
72 cheyenne pdx Registered User Join Date: Nov 2006 Location: Portland Posts: 382	Re: Whatta you think of my dash? I think it is a great look. If I remember right the Old and New Mini's have the speedo in the middle of the dash. I don't think it will be too hard to look a little to the right to see the speed. Are you going to have heat/AC controls? If so, where? Are you leaving the original cluster area smooth like in the picture or are you going to do something in that area. Anyways, great look. You had a vision and went with it. That is why I love this site. Everyone here is willing to give out their ideas and help the less experienced people to make their visions possible.



Register or Log In To remove these advertisements.

10-12-2007, 11:31 AM	#18
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	Re: Whatta you think of my dash? At this stage of the game I am leaving it smooth... I looked at putting the airride controls and some other stuff there but it just doesnt look right... I am going to put the radio and other stuff in the center console.. __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile

10-12-2007, 11:43 AM	#20
c10addict Registered User Join Date: Aug 2007 Location: pittsburgh pa Posts: 1,970	Re: Whatta you think of my dash? no sketch... only in my head... THe glove box door is only used as a filler, not functional, welding the latch hole smooth... I am probably going to get some aluminum stock and make some polished trim accents __________________ 68 C10 Shorty TPI,Bagged, and all the good stuff. Classic trucks feature June 06, On the cover of Jegs Christmas Catalog 08 67 C10 Shorty Shop truck project Bagged and Z'd under destruction and getting nowhere fast. 64 C10 Shop Truck/Daily driver, Bagged, Dropmember, SOLD!!!! Gone but not forgotten.. 54 GMC under the knife getting a S10 chassis swap and bagged. See my build thread... 07 GMC Sierra 5/7 drop, 22's and 24's Air ride on my mind.. http://67-72chevytrucks.com/vboard/s...d.php?t=339340 See pics of my trucks in my profile

10-12-2007, 05:12 PM	#21
boundstaffpress Jamie Hyneman is my twin Join Date: Nov 2005 Location: La Junta, Colorado Posts: 705	Re: Whatta you think of my dash? That is sharp! Jeep had their speedo in the middle for years. Old VW's did, Lots of Model A and T customs do. I think you did a great job. __________________ Justin SOLD 1967 K10 Fleetside, 283, Front and Rear Posi SOLD Color Wiring Diagrams Now in High Resolution V8 and Cab and Cab and Chassis

10-12-2007, 05:13 PM	#22
earl87gta Senior Member Join Date: Dec 2003 Location: Kingsport TN Posts: 4,641	Re: Whatta you think of my dash? I was on a web site not long ago that had a LCD TV that was set up to be all your gages. At the time I tought what would you do with that but now after seeing yours Im thinking you could put it in a glove box door and have only it plus you could watch the news while your driving. __________________ Earl 68 2500 4x4 GMC Burb Last edited by earl87gta; 10-12-2007 at 05:14 PM.

10-12-2007, 06:57 PM	#23
corn Registered User Join Date: Dec 2003 Location: here Posts: 5,789	Re: Whatta you think of my dash? Perfect location? Who gives a crap! Its KEWL! Thats all that matters. Please keep us updated on your shop truck! Last edited by corn; 10-12-2007 at 08:06 PM. Reason: I cant sepll good!

10-12-2007, 07:01 PM	#24
1969k10stepside Registered User Join Date: Mar 2006 Location: USA Posts: 21,020	Re: Whatta you think of my dash? Nice mod!

10-13-2007, 08:13 AM	#25
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,863	Re: Whatta you think of my dash? The speedo in the center just takes a change in old habits.Like said,you just glance at it.It`s not like reaching over and tuning a radio with tiny numbers on it.Many high performance world-class sports cars place the speedo in the center.You don`t have to look through the steering wheel. I`m sure another heater control can be adapted somewhere. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

Register or Log In To remove these advertisements.