03-19-2024, 09:08 AM | #3651 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
#2x3/4" self drill screw
Works better if you predrilled 17108533671323610477507928785123 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-21-2024, 11:59 AM | #3652 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
17110364857403009535035745668611 by [url=https://www.flickr.com/photos/97391199@N06
Chuck in a chuck
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-21-2024, 12:01 PM | #3653 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
17110365478576902649425331948102 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-22-2024, 09:45 AM | #3654 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
The screws are so small that I have to use my hymastats
17111149264951999854906294122015 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-23-2024, 10:11 AM | #3655 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
Oversize hole in patch panel, draws sheet metal tightly
17112028247662920689203766817748 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-25-2024, 11:50 AM | #3656 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
If you're not getting spiraling pig tails, use more lubricant saves on drill bits
17113814976342150880044317980103 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-27-2024, 08:39 AM | #3657 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
17115430442306797632180518517808 by [url=https://www.flickr.com/photos/97391199@N06
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim |
03-27-2024, 08:42 AM | #3658 |
Registered User
Join Date: May 2006
Location: Philadelphia, Pa. 19454
Posts: 9,409
|
Re: PO has me PO'd
17115429655647856498034021472742 by [url=https://www.flickr.com/photos/97391199@N06
In Milwaukee s infinite wisdom they changed the shaft size to 1/2-20, standard shaft for a 3/8 chuch was 3/8-24 ao now I have to make an adapter or put the chuck on my Dewalt Found this out after I watched the video on chuck removal
__________________
Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; Yesterday at 11:13 AM. |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|