56 Chev Garage build

[Kabwe]

Hey rudedude,

The truck is really looking good.

[chevythechief]

Sorry I'm blind Now I know...

[Rude Dude]

Finally finish the top headlight portion of the fenders, had to cut and reweld a section of drivers side near grill. Next need to primer all of the fender and block sand. I think I would rather go to the Dentist than do body work!

[Rude Dude]

Here is one more pic of fender, Don't mind the paint run a bug fly in when I was painting and I tried to take it out mistake, it sanded out al least no dents right.

[Kim57]

It came out nice.
Kim

[Rude Dude]

Thanks Kim

Originally Posted by Kim57

It came out nice.
Kim

[Kabwe]

Hey man,

The truck is looking great. Nice work buddy.

[Rude Dude]

Thank you Kabwe, been really busy with other things it was nice to work on truck again. Going to try and get on Doors next then prime one solid color.

Originally Posted by Kabwe

Hey man,

The truck is looking great. Nice work buddy.

[dug224]

Good choice on the steering wheel. Looks great. dug

[hammerdog57]

I like the look of the tri five steering wheel. What does it take to adapt it to the van column? Any close up pics of the conversion?

[Rude Dude]

It bolts right up if you want to close up the gap between stock wheel and column you can buy an a spacer ring available from. Ididit see this video.

1955-68 Stock GM Steering Wheel Modifications to...

Originally Posted by hammerdog57

I like the look of the tri five steering wheel. What does it take to adapt it to the van column? Any close up pics of the conversion?

[hammerdog57]

Thanks for the info and video.

[Rude Dude]

I like the fancy Aluminum recovery tanks but can't see in spending that much money for something I can not see the fluid in. I needed an overflow tank for the radiator so went to Autozone and bought one of the generic plastic recovery tanks. I used the factory holes that where already drilled, put in Three rubber grommets for hose and two behind the mounting bracket so it wont rub against the the paint, also split a gas line and placed on the lower bracket in two spots that lay against the fender wheel all for under $10.

[Kim57]

Nice clean install on the over flow tank.
Kim

[Rude Dude]

Thanks Kim

Originally Posted by Kim57

Nice clean install on the over flow tank.
Kim

[Rude Dude]

Today I re-did an old bumper, stripped with paint stripper and etch primed and repainted it white. Color sanded too

[Kim57]

Very nice.
Kim

[Rude Dude]

Worked on the doors yesterday just wanted to share a little on a tool my brother recommended to buy and it work great. I have a harbour frieght stud gun and the stud pullers sucks big time, the wheel that holds the studs strips out very quickly after use. My right door was dropped by previous owner (look like a 2nd story drop) and the damage was extensive it buckled the bottom of door and pushed the outter skin up so much so that I was thinking of buying an outter skin and new lower panel. This got be thinking why not use my new tool and fix it so I cut the bottom of door which gave me access to inside skin and using a hammer and dolly I straighten the door as best I could. Then after straightening and welding the bottom I used the tool to finish the rest. I am sorry but I forgot to take pictures on outter stud work but I got pics of the bottom. If you need the tool just google it stud leveler I highly recommend it.

[Rude Dude]

Here is some pics from my left door after using the tool.

[_Ogre]

we have a hf stud gun, works great but we use different tools than the cheap hf pullers too
i'm surprised studs do anything with the thick metal on our trucks
i massaged a fender with two 5lb hammers for a couple hours to fix a crushed lip

[Roadkill58]

Nice work on the truck. I like the mods you are doing.



.

[made2drag]

nice build so far

[Rude Dude]

I finished up passenger door ran out of primer so I used flat black until I buy more primer

[Rude Dude]

A couple more pics

[Kim57]

Looks nice and smooth.
Kim