OR Parting 1972 C30 350/TH400

[DLTruck1973]

Originally Posted by dirtwork

When you have chance to check the thickness of the rotors let me know, as that will have an impact on my decision on them. I'm in for sure as I mentioned before on the crossmember at 75.00 and the spring hanger at 40.00 plus shipping. Shipping cost for rotors is high due to the distance between us which I don't have a problem with as long as they have decent life left. Whenever you get the parts pulled is fine with me, just let me know and we can make payment arrangements however you need.

Thanks
Matt

Hello Matt,

OK, we checked the rotors on the second truck and they are good. The measurements are 1.275 and 1.277. The min thickness on these is 1.216. They have plenty of good material on them and are not grooved up.

What I would like to do is have them machined here for an additional $40.00. They look nice now and I would guess they do not need to have a very much material removed to make them real nice and true.

That is your choice, unless you were planing on running them without machine work.

Let me know. I still need to pull these off the truck depending on your decision.

Thank you again,
Thomas

[oldtrux]

do you still have the gas pedal assembly?thx dan

[DLTruck1973]

Originally Posted by oldtrux

do you still have the gas pedal assembly?thx dan

Hi Dan,

Do you want just the pedal assembly (no cable) or the pedal assembly with the switch and wiring for the 400TH trans.

Pedal assembly alone is $30.00

With the switch and wiring (bad end for the trans) $40.00

With the switch and good wiring harness it is $55.00

All prices are plus shipping.

Let me know and get me your zip code for shipping quote.

Thank you for the interest,
Thomas

[HOTRODSBYCHIP]

Do you still have the front disc brakes spindles? If you do how much for them.

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

Do you still have the front disc brakes spindles? If you do how much for them.

Yes they are still available. $35.00 each plus shipping. I can get you a shipping quote with your zip code.

Thank you for the interest,
Thomas

[dirtwork]

Originally Posted by DLTruck1973

Hello Matt,

OK, we checked the rotors on the second truck and they are good. The measurements are 1.275 and 1.277. The min thickness on these is 1.216. They have plenty of good material on them and are not grooved up.

What I would like to do is have them machined here for an additional $40.00. They look nice now and I would guess they do not need to have a very much material removed to make them real nice and true.

That is your choice, unless you were planing on running them without machine work.

Let me know. I still need to pull these off the truck depending on your decision.

Thank you again,
Thomas

Sounds good to me. Go ahead and pull the rotors from the other truck them and get them machined down. I am on no time line for any of these parts. At your convenience will be fine, just keep me updated on progress. My truck is in storage for winter and paint work. I would assume that the cross member and hanger ship in one box and each rotor has is own? Let me know the total again, and how you would like to be paid.

Thanks again for all your work on this.
Matt

[HOTRODSBYCHIP]

Check the shipping for me 37363 is the zip code
Could you send a picture of them
Thanks

[DLTruck1973]

Originally Posted by dirtwork

Sounds good to me. Go ahead and pull the rotors from the other truck them and get them machined down. I am on no time line for any of these parts. At your convenience will be fine, just keep me updated on progress. My truck is in storage for winter and paint work. I would assume that the cross member and hanger ship in one box and each rotor has is own? Let me know the total again, and how you would like to be paid.

Thanks again for all your work on this.
Matt

Hi Matt,

I am going to send you a PM with details on this.

Thank you,
Thomas

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

Check the shipping for me 37363 is the zip code
Could you send a picture of them
Thanks

I will get you a shipping quote and photos of them tomorrow, if that is OK.

Thank you,
Thomas

[HOTRODSBYCHIP]

Originally Posted by DLTruck1973

I have one that needs to be pulled. It will be $75.00 plus shipping. Application is a 72 Suburban C20 with a 402/400TH trans

Let me know,
Thank you,
Thomas

Do you still have the disc brake spindles and dust shields for this 72 C20 Suburban? If so how much.

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

Do you still have the disc brake spindles and dust shields for this 72 C20 Suburban? If so how much.

The particular 72 C20 Suburban is a while from being parted but I should have a set of spindles and dust shields for the same. Let me get my hands on them and check condition and I can get you a price.

Thank you for the interest,
Thomas

[HOTRODSBYCHIP]

Originally Posted by DLTruck1973

The particular 72 C20 Suburban is a while from being parted but I should have a set of spindles and dust shields for the same. Let me get my hands on them and check condition and I can get you a price.

Thank you for the interest,
Thomas

Ok

[Chuck Burg]

Originally Posted by DLTruck1973

Hi Chuck,

Flat bead is 130 1/2 inch long, 90 1/2 inches wide and 38 tall in the front.

$500.00 picked up.

Here are a few photos. Let me know. The wood is solid also.

I'll pass on this

Thanks for the pics

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

Check the shipping for me 37363 is the zip code
Could you send a picture of them
Thanks

OK,

The C30 spindles are 35.00 each plus shipping at $62.91 gives you a total of $132.91

Here are some photos. I have not had a minute to clean them up but they will get cleaned before they are shipped.

Thank you for the interest,
Thomas

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

Ok

Just wanted to check with you and see if you are looking for 2 sets of these spindles. The C20 and C30 actually use the same spindle.

With that said, the price would be the same at $132.91 shipped. The dust shields would be an extra $10.00 each with the purchase of the spindles.

Let me know,

Thank you,
Thomas

[HOTRODSBYCHIP]

Originally Posted by DLTruck1973

Just wanted to check with you and see if you are looking for 2 sets of these spindles. The C20 and C30 actually use the same spindle.

With that said, the price would be the same at $132.91 shipped. The dust shields would be an extra $10.00 each with the purchase of the spindles.

Let me know,

Thank you,
Thomas

No I need only one set. I wasn't sure if the C30 and C20 spindles were the same. I'll take the spindles with dust shields please.

[DLTruck1973]

Originally Posted by HOTRODSBYCHIP

No I need only one set. I wasn't sure if the C30 and C20 spindles were the same. I'll take the spindles with dust shields please.

I am going to send you a PM with details on payment.

Thank you very much,
Thomas

[HOTRODSBYCHIP]

Originally Posted by DLTruck1973

I am going to send you a PM with details on payment.

Thank you very much,
Thomas

Ok

[HOTRODSBYCHIP]

Originally Posted by DLTruck1973

I am going to send you a PM with details on payment.

Thank you very much,
Thomas

Payment sent

[dirtwork]

Thomas - Got your PM. Thanks!

[DLTruck1973]

Originally Posted by CrewCab59

Please do a shipping quote and pics before you pull!

Scott

PM on the way with a quote

Thank you,
Thomas

[CrewCab59]

Originally Posted by DLTruck1973

PM on the way with a quote

Thank you,
Thomas

Pm back!

Will let you know.

Thanks
Scott

[DLTruck1973]

Originally Posted by DLTruck1973

I have 1 good one. There is paint on it but I believe it would clean up nice. These are not reproduced to my knowledge.

$30.00 plus shipping

I took some time and cleaned this Custom 30 emblem. It is a real nice one, no pitting and good studs.

Thank you,
Thomas

[DLTruck1973]

We still have some nice parts on this truck

Thank you for the interest,
Thomas

[DLTruck1973]

ttt