Rochester B leaking between bowl and horn... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**jabborabbo** · 05-05-2019, 04:55 PM

I rebuilt the carb about a year ago, torqued the screws attaching the horn to the bowl to 70 in-lbs, and haven’t had any problems until today (at least noticeable problems). There was a bit of gas around the gasket (I smelled it before I found it)...The screws weren’t at 70 in-lbs - I re-torqued them and they turned maybe 20 -30 degrees before they were at 70 in-lbs. Is it typical for these carbs to loosen up like that over time?

**kidatheart** · 05-05-2019, 05:06 PM

I’m no mechanic but I would guess the gasket might have shrunk from heat and time. The bolts didn’t loosen-the gasket got thinner.

**Jason Banks** · 05-05-2019, 05:11 PM

Whatever is happening mine does it too...I have a 68 with the monojet, not the B, but I'm constantly tightening the screws on top to stop leaking. I have several of the monojet carbs, but one of the NOS rebuilt ones I got had double gaskets.

**Steeveedee** · 05-05-2019, 11:43 PM

That's a problem with newer kits. Back in the day, you could rebuild a carburetor and expect good performance for many years. If it isn't flooding and blowing black smoke, your float level and float are OK. Just re-tighten the screws when needed.

**jabborabbo** · 05-06-2019, 06:45 PM

Thanks to all!

05-05-2019, 04:55 PM	#1
jabborabbo Senior Member Join Date: Apr 2013 Location: Podunk, Texas Posts: 739	Rochester B leaking between bowl and horn... I rebuilt the carb about a year ago, torqued the screws attaching the horn to the bowl to 70 in-lbs, and haven’t had any problems until today (at least noticeable problems). There was a bit of gas around the gasket (I smelled it before I found it)...The screws weren’t at 70 in-lbs - I re-torqued them and they turned maybe 20 -30 degrees before they were at 70 in-lbs. Is it typical for these carbs to loosen up like that over time? __________________ "It is hard to search for a black cat in a dark room, particularly if it is not there. Especially if this cat is smart, brave, and polite." Sergei Shoigu, Russian Minister of Defense

05-05-2019, 05:06 PM	#2
kidatheart Senior Member Join Date: May 2012 Location: Assaria, Ks Posts: 465	Re: Rochester B leaking between bowl and horn... I’m no mechanic but I would guess the gasket might have shrunk from heat and time. The bolts didn’t loosen-the gasket got thinner.

05-05-2019, 05:11 PM	#3
Jason Banks Senior Member Join Date: Dec 1999 Location: TX Posts: 1,495	Re: Rochester B leaking between bowl and horn... Whatever is happening mine does it too...I have a 68 with the monojet, not the B, but I'm constantly tightening the screws on top to stop leaking. I have several of the monojet carbs, but one of the NOS rebuilt ones I got had double gaskets.

05-05-2019, 11:43 PM	#4
Steeveedee Who Changed This? Join Date: Jan 2013 Location: Simi Valley, CA Posts: 10,076	Re: Rochester B leaking between bowl and horn... That's a problem with newer kits. Back in the day, you could rebuild a carburetor and expect good performance for many years. If it isn't flooding and blowing black smoke, your float level and float are OK. Just re-tighten the screws when needed. __________________ ~Steven '70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper Simi Valley, CA

05-06-2019, 06:45 PM	#5
jabborabbo Senior Member Join Date: Apr 2013 Location: Podunk, Texas Posts: 739	Re: Rochester B leaking between bowl and horn... Thanks to all! __________________ "It is hard to search for a black cat in a dark room, particularly if it is not there. Especially if this cat is smart, brave, and polite." Sergei Shoigu, Russian Minister of Defense

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.