camaro tach - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67ChevyC10Stepside · 01-22-2005, 08:46 PM

this question is asked so much that i thought i would post as much about this as possible in one place. i've never given instructions like this before so bear with me. ok...when you get down to it it's really easy to do. i went on ebay and bought a camaro tach for 11.50. correct me if im wrong but 70-81 are the years that work. there are a couple different needle choices so that's the main deciding factor when purchasing. first start by taking your guage panel apart. there are i think 18? screws that hold the bezel on. i started with the front metal plate which is shown here. cut out the area outlined in red. be careful and take your time cut only to the depressed area. i used a dremel tool to do this.

67ChevyC10Stepside · 01-22-2005, 08:52 PM

the next step is the lens. i used cp and some scrubbing to remove the lines shown in red here.

67ChevyC10Stepside · 01-22-2005, 09:00 PM

next the tach needs some work done to it. it comes with an insulator plate on it. you need to remove that. it will leave the tach with it's head the wires and a little circuit board with a plastic plate. just take the plate off. make a note of where the wires go on the circuit (they are engraved on the insulator plate)

67ChevyC10Stepside · 01-22-2005, 09:04 PM

next you have the back plate. some people beat the hump flat i just cut it out. the red part is what gets in the way. the black dots is one place you can mount your circuit. i used the plastic plate that comes with the tach and mounted it on the backing plate of my guage setup that way i can connect the wires to the back of the setup and be done.

67ChevyC10Stepside · 01-22-2005, 09:06 PM

ok...now you will have to trim the top and bottom of the tach a little...i just used some tin snips.(it's too tall to fit in the top plate) when you take the tach apart there is a oil light there that leaves a open space on the face. what i did for this was take electrical tape...and put a short piece onto a longer piece so that the hole was covered with the non sticky side but there was enough to secure it from the back side.

67ChevyC10Stepside · 01-22-2005, 09:09 PM

then you are ready to start putting it back together.

67ChevyC10Stepside · 01-22-2005, 09:10 PM

here is mine. it still has the crappy bezel on it etc but i am gonna be changing all that. i will get pics of the inside and back of it when i work on my truck again.

c10crazy · 01-22-2005, 09:49 PM

Here is the original post from awhile back with instructions also. http://67-72chevytrucks.com/vboard/s...threadid=37673

67ChevyC10Stepside · 01-22-2005, 09:51 PM

yeah he did it harder way than me....he kept the circuit floating around inside. i put it through the backing plate. either way works though.

jhwkns · 01-22-2005, 11:33 PM

A couple of those pictures look familar

Not all gen.II camaro tachs are the same. The one I used required me to cut a 1 3/4" hole in the back of the housing. It protruded through only about 1/4" so the printed circuit fit over it no problem. I sealed the hole with some 10mil vinyl tape. To allow light to reach the face I spaced it away from the front plate using cabinet door silencing pads. These are adhesive backed, and available at any hardware store. I'm probably going to disassemble mine to repaint the needles. When I do I'll take a couple more pictures.

67ChevyC10Stepside · 01-22-2005, 11:57 PM

which one is yours? i was told to cut away part of the lip for the light to show through.

67ChevyC10Stepside · 01-22-2005, 11:58 PM

every 70-81 tach i have seen was the same with a couple needles the only difference.

jhwkns · 01-23-2005, 12:21 AM

Mines the one on the oak table.

67ChevyC10Stepside · 01-23-2005, 12:40 AM

how did you do your wire hookups?

67ChevyC10Stepside · 02-01-2005, 11:41 PM

ok...you people better appreciate these pics. i broke my wire connector for my coil taking this freakin panel out lol

Blue85 · 02-07-2005, 07:01 PM

so what year camaro tach will work?

67ChevyC10Stepside · 02-07-2005, 08:00 PM

Quote:

Originally Posted by 67ChevyC10Stepside

this question is asked so much that i thought i would post as much about this as possible in one place. i've never given instructions like this before so bear with me. ok...when you get down to it it's really easy to do. i went on ebay and bought a camaro tach for 11.50. correct me if im wrong but 70-81 are the years that work. there are a couple different needle choices so that's the main deciding factor when purchasing. first start by taking your guage panel apart. there are i think 18? screws that hold the bezel on. i started with the front metal plate which is shown here. cut out the area outlined in red. be careful and take your time cut only to the depressed area. i used a dremel tool to do this.

chevy72blu · 02-20-2005, 02:41 PM

Quote:

Originally Posted by Blue85

so what year camaro tach will work?

70-81

Im gonna do it this weekend =)

01-22-2005, 08:46 PM	#1
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	camaro tach this question is asked so much that i thought i would post as much about this as possible in one place. i've never given instructions like this before so bear with me. ok...when you get down to it it's really easy to do. i went on ebay and bought a camaro tach for 11.50. correct me if im wrong but 70-81 are the years that work. there are a couple different needle choices so that's the main deciding factor when purchasing. first start by taking your guage panel apart. there are i think 18? screws that hold the bezel on. i started with the front metal plate which is shown here. cut out the area outlined in red. be careful and take your time cut only to the depressed area. i used a dremel tool to do this. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 08:52 PM	#2
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	the next step is the lens. i used cp and some scrubbing to remove the lines shown in red here. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:00 PM	#3
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	next the tach needs some work done to it. it comes with an insulator plate on it. you need to remove that. it will leave the tach with it's head the wires and a little circuit board with a plastic plate. just take the plate off. make a note of where the wires go on the circuit (they are engraved on the insulator plate) Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:04 PM	#4
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	next you have the back plate. some people beat the hump flat i just cut it out. the red part is what gets in the way. the black dots is one place you can mount your circuit. i used the plastic plate that comes with the tach and mounted it on the backing plate of my guage setup that way i can connect the wires to the back of the setup and be done. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:06 PM	#5
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	ok...now you will have to trim the top and bottom of the tach a little...i just used some tin snips.(it's too tall to fit in the top plate) when you take the tach apart there is a oil light there that leaves a open space on the face. what i did for this was take electrical tape...and put a short piece onto a longer piece so that the hole was covered with the non sticky side but there was enough to secure it from the back side. __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:09 PM	#6
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	then you are ready to start putting it back together. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:10 PM	#7
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	here is mine. it still has the crappy bezel on it etc but i am gonna be changing all that. i will get pics of the inside and back of it when i work on my truck again. Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 09:49 PM	#8
c10crazy Like a Rock! Join Date: May 2002 Location: USA Posts: 1,092	Here is the original post from awhile back with instructions also. http://67-72chevytrucks.com/vboard/s...threadid=37673 __________________ 69 LWB Runs great - work in progress Mess with me and you mess with the whole trailer park! Last edited by augie; 04-11-2011 at 11:30 PM.

01-22-2005, 09:51 PM	#9
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	yeah he did it harder way than me....he kept the circuit floating around inside. i put it through the backing plate. either way works though. __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 11:33 PM	#10
jhwkns Registered Cruiser Join Date: May 2002 Location: Las Vegas NV Posts: 2,230	A couple of those pictures look familar Not all gen.II camaro tachs are the same. The one I used required me to cut a 1 3/4" hole in the back of the housing. It protruded through only about 1/4" so the printed circuit fit over it no problem. I sealed the hole with some 10mil vinyl tape. To allow light to reach the face I spaced it away from the front plate using cabinet door silencing pads. These are adhesive backed, and available at any hardware store. I'm probably going to disassemble mine to repaint the needles. When I do I'll take a couple more pictures. __________________ I intend to live forever. So far, so good.

01-22-2005, 11:57 PM	#11
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	which one is yours? i was told to cut away part of the lip for the light to show through. __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-22-2005, 11:58 PM	#12
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	every 70-81 tach i have seen was the same with a couple needles the only difference. __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

01-23-2005, 12:21 AM	#13
jhwkns Registered Cruiser Join Date: May 2002 Location: Las Vegas NV Posts: 2,230	Mines the one on the oak table. __________________ I intend to live forever. So far, so good.

01-23-2005, 12:40 AM	#14
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	how did you do your wire hookups? __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.

02-01-2005, 11:41 PM	#15
67ChevyC10Stepside Registered User Join Date: Mar 2004 Location: Butler PA Posts: 3,034	ok...you people better appreciate these pics. i broke my wire connector for my coil taking this freakin panel out lol Attached Images __________________ 67 c-10, 400 SB, TH350, 4.10 gears, Blazer tank,camaro tach, sidemarker fuel fill (soon) WTB: stepside parts, 67 front end parts, 67 small window cab. posi for 3.73 or 4.10 for 12 bolt and 10 bolt.



Register or Log In To remove these advertisements.

02-07-2005, 07:01 PM	#16
Blue85 Oilfield Trash Join Date: Sep 2003 Location: Raymore, Sk, Canada, Earth Posts: 3,171	so what year camaro tach will work? __________________ 14 Dodge 3500 Mega Cab 08 Dodge 3500 Mega Cab 87 Chev 3+3 4x4 80 GMC K10 High Sierra bone stock 70 Chevelle 350SS long term project 68 GMC 3ton Grain Truck/Garbage wagon 50 Pontiac 2 Door Coupe Project "I've got a shotgun rifle and a 4 wheel drive and a country boy can survive" Hank Jr.

Register or Log In To remove these advertisements.