What did you do to your truck today.The 3rd chapter - Page 21 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**71CHEVYSHORTBED402** · 04-22-2019, 02:51 PM

Just finished these. This is the second water pump I painted, because dummy didn't think to fit the first one. The GMB "OE" replacement is not an OE replacement (BBC), doesn't quite clear the factory timing chain cover. I'll be most replacements are the same.

They probably figure you can just bend the cover, but I'd rather eat the labor. A four hour lesson learned, because both were brushed. Should have bought the Delco to begin with. It's a lighter pump too.

72c20customcamper · 04-22-2019, 06:25 PM

Pulled the two saddle tanks. Going to Carlisle so they will be for sale there.

Metaldoc · 04-22-2019, 08:22 PM

All detailed up

**Canuckvetter** · 04-22-2019, 10:08 PM

Quote:

Originally Posted by Metaldoc

All detailed up

Looking good. Already for the 2019 season!

**zicc1835** · 04-22-2019, 10:22 PM

Quote:

Originally Posted by gmc1969custom

Put some on new Tires and painted my steels a nice bright white.

those are beautiful

**zicc1835** · 04-22-2019, 10:25 PM

Quote:

Originally Posted by 70STOVEBOLT

Yes. I don't have a pic from the side but it is approximately even with the bottom of the frame rail, you can see the headers a little bit though.

thanks for the reply what brand headers do you have a part # ?

**RodnRudy** · 04-23-2019, 07:54 AM

Quote:

Originally Posted by Already Gone

Nice engine. Is that roller rockers on it and where did you get the valve covers, I like them.

Not roller rockers, just OEM. The valve covers are Billet Specialties. Got them through Summit like most parts cause you get free shipping.

**71CHEVYSHORTBED402** · 04-25-2019, 11:54 PM

Swapped out a battery box is all. The bolts can be a real (^( without pulling the radiator. The box I wanted is solid. I don't see any pitting, but know better. Hopefully it suits my rebuild.

Pulled the RH skirt off the same truck recently. Fitted a few skirts on it, practice

I was hoping to use it for the rebuild as well. Nice fender, but too much rust in front. So I'm in the hunt for a RH fender. That or pair of replacements.

**Canuckvetter** · 04-26-2019, 02:28 AM

http://67-72chevytrucks.com/vboard/a...1&d=1556259847
Cleaned up 4 horn buttons. Disassembled. Polished out scratches starting with 220 grit wet sand worked up to 7000 grit.

**70STOVEBOLT** · 04-26-2019, 10:49 AM

Quote:

Originally Posted by zicc1835

thanks for the reply what brand headers do you have a part # ?

I keep missing your replies. Hedman 68190, for 68-72 Chevelle I painted them with Rustoleum high heat paint. Don't have the $$$$ for Jet Hot coating...

cruisinthe34 · 04-26-2019, 04:41 PM

Almost finished the interior:

**SoCoC10** · 04-26-2019, 07:55 PM

Finished my interior too

**70STOVEBOLT** · 04-26-2019, 09:48 PM

Mostly, neglected and drank some beer, but I did finish blasting the air cleaner, shot the first coat of paint on it. Sorry, no pics, it’s at work.

**Steeveedee** · 04-26-2019, 11:05 PM

Quote:

Originally Posted by cruisinthe34

Almost finished the interior:

Nice!

Quote:

Originally Posted by SoCoC10

Finished my interior too

...and Nice!

Gotta get after my interior and dash. Interior is shot and I want to get more instrumentation than the stock gauge dash has.

Metaldoc · 04-27-2019, 12:16 AM

Mines all back as well.

**zicc1835** · 04-27-2019, 08:43 AM

Quote:

Originally Posted by 70STOVEBOLT

I keep missing your replies. Hedman 68190, for 68-72 Chevelle I painted them with Rustoleum high heat paint. Don't have the $$$$ for Jet Hot coating...

thank you for the reply

**RodnRudy** · 04-27-2019, 05:02 PM

I got the engine fired and run in yesterday and today I put my Billet Specialties Speedways back on and put her on the ground. I went back to the 5 1/2, 7" static drop I had and I like the look a lot more. Ran to the gas station and filled her up and took her for a spin before the rain showed up. Life is good.

**Ol Blue K20** · 04-27-2019, 07:55 PM

I like it a lot!! How's it run? I'm guessing good as it looks.....

**Thrill4130** · 04-27-2019, 11:33 PM

I tried getting my horn setup fixed. I was missing the pin. Also went to car show and saw this cool carryall.
Posted via Mobile Device

**RodnRudy** · 04-28-2019, 08:38 AM

Quote:

Originally Posted by Ol Blue K20

I like it a lot!! How's it run? I'm guessing good as it looks.....

It runs well so far. The ride is "firm" being lowered that much but I like it that way.

**SoCoC10** · 04-29-2019, 10:02 AM

First car show of the year.

**70STOVEBOLT** · 04-29-2019, 10:06 AM

Replaced timing chain (stretched).

**Mts67C10K20** · 04-29-2019, 11:17 AM

Not ready to put the interior back yet
But making progress on the floors and rockers

**Grumpy old man** · 04-29-2019, 03:54 PM

'67 Cut out dash repair . A little more work adding A/C vents and this will be done .

**71CHEVYSHORTBED402** · 05-03-2019, 01:05 AM

A year ago I tried my spray gun for the first time. I sprayed Por-15 engine enamel. Got frustrated early, cleaned up the parts and declared I'd leave any spray gun business to the pros. Bet the paint was too thick. I thinned it, but probably not enough.

The enamel doesn't brush on most smooth surfaces with great success. I brushed the timing chain cover up nicely, but that's where it ended.

Today I thought to try spraying again, only this time I met their 5/1 thinning max. In my novice opinion, it could have sprayed a bit heavier. I still didn't break out the gun, used a Preval instead

I really should learn to use a spray gun. In hindsight I may sprayed all the Chevy Orange through a gun

All precautions spraying this stuff. Fans, open garage, good respirator....It's bad stuff, and lingers a while.

On a side, anyone know where that J-hook goes on a 71 BBC, and what it's used for? I removed it 25 or so years ago, can't remember

I know it was Chevy Orange from factory, and don't believe it was rubber coated. I can't check right now, but it looks to take a 3/8" bolt, or even a 7/16" bolt tightly. Seems it goes on a head someplace, maybe even a stud, like off a water pump or thermostat housing.

04-22-2019, 02:51 PM	#501
71CHEVYSHORTBED402 Senior Member Join Date: Feb 2009 Location: Northern Nevada Posts: 7,118	Re: What did you do to your truck today.The 3rd chapter Just finished these. This is the second water pump I painted, because dummy didn't think to fit the first one. The GMB "OE" replacement is not an OE replacement (BBC), doesn't quite clear the factory timing chain cover. I'll be most replacements are the same. They probably figure you can just bend the cover, but I'd rather eat the labor. A four hour lesson learned, because both were brushed. Should have bought the Delco to begin with. It's a lighter pump too. Attached Images __________________ Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assm. guide "kit" for restoring it from ground up. With assys, the guide accts for 1000s of OEM identifications and part numbers, all written in short order. 700+ images include assm, illust., charts, and points of interest. Much of the info. applies to all 67-72 GM trucks, and to a lessor degree all 67-72 GM vehicles. My build thread, and more on the guide https://67-72chevytrucks.com/vboard/...d.php?t=730025

04-22-2019, 06:25 PM	#502
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,139	Re: What did you do to your truck today.The 3rd chapter Pulled the two saddle tanks. Going to Carlisle so they will be for sale there. __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

04-22-2019, 08:22 PM	#503
Metaldoc Registered User Join Date: Apr 2015 Location: Ayr Ontario Posts: 1,122	Re: What did you do to your truck today.The 3rd chapter All detailed up Attached Images __________________ Do it, Do it right, Do it right the first time

04-25-2019, 11:54 PM	#508
71CHEVYSHORTBED402 Senior Member Join Date: Feb 2009 Location: Northern Nevada Posts: 7,118	Re: What did you do to your truck today.The 3rd chapter Swapped out a battery box is all. The bolts can be a real (^( without pulling the radiator. The box I wanted is solid. I don't see any pitting, but know better. Hopefully it suits my rebuild. Pulled the RH skirt off the same truck recently. Fitted a few skirts on it, practice I was hoping to use it for the rebuild as well. Nice fender, but too much rust in front. So I'm in the hunt for a RH fender. That or pair of replacements. __________________ Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assm. guide "kit" for restoring it from ground up. With assys, the guide accts for 1000s of OEM identifications and part numbers, all written in short order. 700+ images include assm, illust., charts, and points of interest. Much of the info. applies to all 67-72 GM trucks, and to a lessor degree all 67-72 GM vehicles. My build thread, and more on the guide https://67-72chevytrucks.com/vboard/...d.php?t=730025

04-26-2019, 02:28 AM	#509
Canuckvetter How did I get this OLD! Join Date: Dec 2014 Location: Lamont County, AB, CANADA Posts: 1,041	Re: What did you do to your truck today.The 3rd chapter http://67-72chevytrucks.com/vboard/a...1&d=1556259847 Cleaned up 4 horn buttons. Disassembled. Polished out scratches starting with 220 grit wet sand worked up to 7000 grit. Attached Images __________________ 1967 Oshawa built LWB Fleetside. 327,3 OTT, 515 Vermilion, CST, PS, PB, Shoulder Harness, Tach,Vac, Speed Warning, Choke Delete, Manual Throttle, Fawn interior. Dealer installed A/C 04/2015, N34 Rosewood Wheel 06/2023 Members who I have met personally. Metaldoc, chevnkevin, 62 Longbed, 72LHorn, 72MARIO, YBNORML, TBONE1964, Classic Bowties, Chevemall, Dagnabbitt.

04-26-2019, 04:41 PM	#511
cruisinthe34 Registered User Join Date: Sep 2015 Location: Charleston, WV Posts: 228	Re: What did you do to your truck today.The 3rd chapter Almost finished the interior: __________________ Steve My Build Thread: http://67-72chevytrucks.com/vboard/s...=morning+glory 1971 C10 Inline 6 250 700R4 "Marlene" 1934 Chevrolet Master Sedan 350 700R4 "Iris" 1941 Ford 1/2 Ton 5.0 H.O Roller C-4 "Rose" 2019 Honda Ridgeline

04-26-2019, 07:55 PM	#512
SoCoC10 Senior Member Join Date: Nov 2014 Location: Colorado Posts: 3,142	Re: What did you do to your truck today.The 3rd chapter Finished my interior too Attached Images __________________ 07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count

04-26-2019, 09:48 PM	#513
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,209	Re: What did you do to your truck today.The 3rd chapter Mostly, neglected and drank some beer, but I did finish blasting the air cleaner, shot the first coat of paint on it. Sorry, no pics, it’s at work. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Coming soon: EFI 2015 Silverado 1500 LS 4.3/6L80/3.23

04-27-2019, 12:16 AM	#515
Metaldoc Registered User Join Date: Apr 2015 Location: Ayr Ontario Posts: 1,122	Re: What did you do to your truck today.The 3rd chapter Mines all back as well. Attached Images __________________ Do it, Do it right, Do it right the first time

04-27-2019, 05:02 PM	#517
RodnRudy Senior Member Join Date: Oct 2014 Location: New Palestine In Posts: 930	Re: What did you do to your truck today.The 3rd chapter I got the engine fired and run in yesterday and today I put my Billet Specialties Speedways back on and put her on the ground. I went back to the 5 1/2, 7" static drop I had and I like the look a lot more. Ran to the gas station and filled her up and took her for a spin before the rain showed up. Life is good. Attached Images __________________ Phil "Money is only a tool to create and achieve what you want most in life" PayPal: rodnrudy@comcast.net

04-27-2019, 07:55 PM	#518
Ol Blue K20 Proprietor of Dale's Corner Join Date: Nov 2012 Location: Vacaville , CA Posts: 15,834	Re: What did you do to your truck today.The 3rd chapter I like it a lot!! How's it run? I'm guessing good as it looks..... __________________ "Some Days Chickens And Some Days Feathers" Dale XNGH ECV Sam Brannan 1004 R.I.P. 67ChevyRedneck R.I.P. Grumpy Old Man

04-27-2019, 11:33 PM	#519
Thrill4130 Active Member Join Date: Nov 2015 Location: Stallion Springs, CA Posts: 190	I tried getting my horn setup fixed. I was missing the pin. Also went to car show and saw this cool carryall. Posted via Mobile Device Attached Images

04-29-2019, 10:02 AM	#521
SoCoC10 Senior Member Join Date: Nov 2014 Location: Colorado Posts: 3,142	Re: What did you do to your truck today.The 3rd chapter First car show of the year. Attached Images __________________ 07' Extcab Silverado Z71 Silver Birch, 5.3L HO 71' Cheyenne C10 Hugger Orange on Saddle SWB Besides these two, too Many to count

04-29-2019, 10:06 AM	#522
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 6,209	Re: What did you do to your truck today.The 3rd chapter Replaced timing chain (stretched). __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Power windows Power Locks Coming soon: EFI 2015 Silverado 1500 LS 4.3/6L80/3.23

04-29-2019, 11:17 AM	#523
Mts67C10K20 Senior Member Join Date: May 2017 Location: Dowagiac Michigan Posts: 202	Re: What did you do to your truck today.The 3rd chapter Not ready to put the interior back yet But making progress on the floors and rockers Attached Images



Register or Log In To remove these advertisements.

04-29-2019, 03:54 PM	#524
Grumpy old man Senior Member Join Date: Dec 2013 Location: Gods country East,Tn Posts: 8,545	Re: What did you do to your truck today.The 3rd chapter '67 Cut out dash repair . A little more work adding A/C vents and this will be done . Attached Images __________________ 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop Last edited by Grumpy old man; 04-29-2019 at 04:00 PM.

05-03-2019, 01:05 AM	#525
71CHEVYSHORTBED402 Senior Member Join Date: Feb 2009 Location: Northern Nevada Posts: 7,118	Re: What did you do to your truck today.The 3rd chapter A year ago I tried my spray gun for the first time. I sprayed Por-15 engine enamel. Got frustrated early, cleaned up the parts and declared I'd leave any spray gun business to the pros. Bet the paint was too thick. I thinned it, but probably not enough. The enamel doesn't brush on most smooth surfaces with great success. I brushed the timing chain cover up nicely, but that's where it ended. Today I thought to try spraying again, only this time I met their 5/1 thinning max. In my novice opinion, it could have sprayed a bit heavier. I still didn't break out the gun, used a Preval instead I really should learn to use a spray gun. In hindsight I may sprayed all the Chevy Orange through a gun All precautions spraying this stuff. Fans, open garage, good respirator....It's bad stuff, and lingers a while. On a side, anyone know where that J-hook goes on a 71 BBC, and what it's used for? I removed it 25 or so years ago, can't remember I know it was Chevy Orange from factory, and don't believe it was rubber coated. I can't check right now, but it looks to take a 3/8" bolt, or even a 7/16" bolt tightly. Seems it goes on a head someplace, maybe even a stud, like off a water pump or thermostat housing. Attached Images __________________ Tony 71 Custom Deluxe, SWB, 2WD, 402, A/C. I developed an assm. guide "kit" for restoring it from ground up. With assys, the guide accts for 1000s of OEM identifications and part numbers, all written in short order. 700+ images include assm, illust., charts, and points of interest. Much of the info. applies to all 67-72 GM trucks, and to a lessor degree all 67-72 GM vehicles. My build thread, and more on the guide https://67-72chevytrucks.com/vboard/...d.php?t=730025 Last edited by 71CHEVYSHORTBED402; 05-03-2019 at 01:36 AM.

Register or Log In To remove these advertisements.