The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board > projects and builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-23-2018, 02:14 PM   #26
cwcarpenter98
Registered User
 
cwcarpenter98's Avatar
 
Join Date: Jan 2018
Location: Woodstock, GA and Milledgeville, GA
Posts: 517
Re: SkinnyG's '61 Apache

Seeing long steppers makes me want to swap my long fleet to a long step. Your truck looks really good, and I think that you should build it however you want to build it
__________________
Christian Carpenter - Instagram: #green63c10
1963 C10 - Frankentruck
1995 Dodge Dakota Sport
"I'll put it simple: if you're going hard enough left, you'll find yourself turning right." - Doc Hudson
cwcarpenter98 is offline   Reply With Quote
Old 12-26-2018, 07:01 PM   #27
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Bottom end all apart. Bearings look really good. Almost "I might reuse these" good.







__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 12-27-2018, 09:03 PM   #28
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Parts ordered. Thanks RockAuto for the discount code, saved me $36CDN.

Summit Racing got me the things RockAuto didn't carry.

I -did- order ARP head studs. I waffled over this for months. Golly are they pricey. Theoretically ARP bolts are certainly good enough, but I think I feel a bit better (and lighter) knowing that this is the best way to go. If I venture close to 22psi, I'll wish I had run studs. I know, I know, the Sloppy guys re-use torque-to-yield fasteners, and they still live to tell the tale.....

I also ordered all new bearings. Even though these bearings look really good, they have taken a bit of schmoo through them, embedding the junk like they are designed to do. I figured "I'm here, why would i not put fresh bearings in?"

Interestingly, if I ship Summit's stuff to my Customs Broker in the States, I have to pay WA sales tax, plus the broker's fees and taxes. If I get it shipped to my house, it's really not that expensive. I don't know how Summit is doing it, but I like it.

Or, I miss-read everything, and I have a BIG bill coming......
__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 01-03-2019, 03:52 PM   #29
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Top end all apart. Valve guides are on the loose side of still acceptable.









Rock Auto delivers! PAC-1218 valve springs should arrive early next week. ARP junk from Summit Racing will ship once the back ordered crank bolt comes in.



Going pick up some diesel to soak and clean the heads and pistons.
__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 01-09-2019, 01:14 AM   #30
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Engine cleaned up real easy!



And my porting kit came in!

__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 05-01-2019, 10:43 AM   #31
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Sold my last beast, so I should dig into this project real quick. Yay!
__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 05-26-2019, 09:48 PM   #32
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Grrrr.

I soaked a head in Diesel for a full week, but it wasn't coming clean very easily. So I took them to a shop and said "clean 'em, do the guides, do the seats, and surface them."

I came back the next day, and they only surfaced the heads. I asked why, and they said they need the valves to check the guides. I said I had measured them two different ways and they're loose, just do them. They were adamant that they needed the valves. So (instead of walking away like I should have), I brought them the valves the next day.

Came back to pick them up, and they said proudly "We didn't even measure them, we wiggled them, they're mint!" You suck, machine shop, you suck. They did cut the seats, but they ended up cutting them pretty deep and now there is a deep ridge around the valves hindering flow.


See the edge above the top cut on the exhaust? Ugh.

Thing is, seat cutting is referenced off the guides. If I do the guides now, the seats have to be re-cut as they will not be concentric with the guides, and then the valves go deeper into the head. Grrr.

I thanked them, paid them, took my stuff, and I'll never go back, nor will I ever recommend them to anyone else.

I recognize I'm not a professional machinist, but dang it, just do what I ask and bill me accordingly. At this rate, though, I may eventually run out of machine shops.

So, I spent a number of hours re-shaping the valve seat area in the combustion chambers to get the flow back, and figured while I'm at it, why not polish the combustion chambers?

Since I didn't have any old valves, I turned down some round stock to 0.313" and threaded one end 1/4-20, and cut out some 1/8" flat and turned them to protect the valve seats.





Research indicates possible advantages being:
More combustion heat applied to piston
More heat kept in exhaust to spool the turbo faster
Less carbon build up
Less "edges" risking pre-ignition and detonation

Could also be pipe dreams and voodoo.



I polished the piston tops as well. Because why not. My labour is free.



After a fair bit of research and debate, I likely will not hog out these heads with porting. I think the swirl ramp in the intake bowls is a good idea for low-speed throttle response, torque and fuel economy. I haven't decided if I will remove the rocker-stud boss in the intake port (done on pretty much all ported and aftermarket heads).

Of course, on one side of the fence you have "Awesome! That's the best mod you could do right there!" and on the other side you have "Dude! You just ruined those heads." Well, I did what made sense to me. We'll see if I get lucky.
__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 05-26-2019, 09:51 PM   #33
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

Painted the valve covers because I needed a distraction. Gray, as the general consensus is the V8's were painted gray in '61. And the interior will be gray (which -is- the '61 colour).



I mistakenly ordered Gen3 rings for my Gen3 block. Turned out the engine had Gen4 guts inside. I found out my mistake after gapping the first rings and discovering they didn't fit the pistons.

So I ordered a new set of Gen4 rings, and gapped them 0.026/0.028" (should be safe for upwards of 22psi boost or so) and installed 'em!



__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Old 05-26-2019, 09:55 PM   #34
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 757
Re: SkinnyG's '61 Apache

I drove the '61 into the shop today to have a good look-see at the bottom; help formulate my game plan. It all looks pretty typical.









It -looks- like it could lay rocker easily, as the frame rails are a lot shorter on these X-Frame trucks. Pancake the front crossmember, sure. Do something about the bottom of the X, maybe. Will the Trailing Arms tuck in high enough at the back of the frame??

I picked up a set of 88-98 2" spindles as well as a Ford 9" axle, plus some 18" Grand Cherokee wheels (5x5 pattern). I need to figure out how I want to deal with all that. The axle swap is easy. Keeping the torsion bars is nice and convenient and affordable, but a challenge.









Something in the front of the truck kept creaking as it sat on the lift. That wasn't scary at all </sarcasm>.
__________________
Nostrildamus - 1961 Apache, soon to go under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
SkinnyG is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:21 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com