The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1969 - 1972 Blazers and Jimmys Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-11-2019, 02:35 AM   #1
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Engine/Trans opinions

I am getting down to decision time. My 69 Blazer did not come with an engine. I will probably go with a moderately built up 350. I have a TH350 that came with it and a 10 spline and 27 spline NP205. I believe it was a 4 speed originally. I have the clutch pedal bracket.. I have the gears changed out to 4:56 and I will run 35" tires. I kind of like the idea of going back to a manual trans, but I can live with an auto.
So... this Blazer will be an on road weekend cruiser and will probably never see the interstate. I would like to avoid a bunch of expensive adapters in order to use a five speed. (unless someone knows a combo that will work)

What are the opinions on these options.

SM465 using the 10 spline (is this trans worth the effort)

convert to a 5 speed (NV 3500-4500)

TH350 with 27 spline

700R4 with 27 spline

Or should I think about a complete modern LS and trans.


Thanks, Keith

Last edited by Keith6987; 02-11-2019 at 01:14 PM. Reason: Typo
Keith6987 is offline   Reply With Quote
Old 02-11-2019, 01:21 PM   #2
SeventyOne
Registered User
 
Join Date: Mar 2007
Location: Oakland, Ca
Posts: 1,359
Re: Enginge/Trans opinions

There's going to be a lot of opinion thrown around but really this comes down to your preferences and tolerances.

If you enjoy shifting and all that go with a manual. I have a '64 F100 that has a 3 speed in it that i originally thought about changing to a automatic for ease of drivability but...i think ive changed my mind and really enjoy banging through the gears. It makes me think more, and be more in tune with the truck - and traffic for that matter - which is sort of the whole point of driving an old rig. At least to me.

My Blazer has a 383 and 700r4 (37" tires and 4.56 gears). Now, I haven't driven it yet since I'm still putting it back together but I personally wanted an overdrive trans so my RPMs are lower at highway speed.

Now that said if you think you'll never see the highway, will you need an OD or even a 5 speed trans?

You need to really think about how the truck will be used and if you DO end up on the highway what are your tolerances for higher RPMs? Using a calculator and putting in your specs with a non-OD trans put you at 2850 at 65 mph. For comparison my K5 would run at 1900rpm at 65mph.

Figure out how you want it to drive then select the best combo for it.

My 2 cents.

Last edited by SeventyOne; 02-11-2019 at 01:36 PM.
SeventyOne is offline   Reply With Quote
Old 02-11-2019, 06:12 PM   #3
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Thanks for your input. The old trucks I’ve driven over the years have all been manual. My Jeep is a manual. There is just an old school feel to driving a stick once in a while. I like to downshift and let it cackle. I was 90% sure I was going with the 700R4 just because it would line up with the NP205 with the least trouble. From what I can tell the only manual that will pop right in is the SM 465.
Keith6987 is offline   Reply With Quote
Old 02-11-2019, 08:24 PM   #4
SeventyOne
Registered User
 
Join Date: Mar 2007
Location: Oakland, Ca
Posts: 1,359
Re: Enginge/Trans opinions

Quote:
Originally Posted by Keith6987 View Post
Thanks for your input. The old trucks I’ve driven over the years have all been manual. My Jeep is a manual. There is just an old school feel to driving a stick once in a while. I like to downshift and let it cackle. I was 90% sure I was going with the 700R4 just because it would line up with the NP205 with the least trouble. From what I can tell the only manual that will pop right in is the SM 465.
The 700r4 needs either a new output shaft or an adapter to mate to the NP205.

If you get the new output shaft it bolts up just like your TH350 would. The other thing when you put in a 700r4 the trans is 1-7/8" longer than a TH350 so you need to either move the engine forward (my choice) or the tcase back.

I'd imagine the SM465 would bolt right in assuming you have the right crossmembers and such. The SM465 came in these as a stock option right?
SeventyOne is offline   Reply With Quote
Old 02-11-2019, 08:47 PM   #5
simicrintz
Registered User
 
Join Date: Dec 2017
Location: Escondido
Posts: 305
Re: Enginge/Trans opinions

350 with factory 4 speed manual trans here. I can hold 75 all day long on the freeway
__________________
-Bruce
1971 K5 Blazer 4WD
simicrintz is offline   Reply With Quote
Old 02-17-2019, 10:44 PM   #6
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by simicrintz View Post
350 with factory 4 speed manual trans here. I can hold 75 all day long on the freeway
So you feel the sm465 is decent tranny for weekend back road cruising?
Keith6987 is offline   Reply With Quote
Old 02-23-2019, 12:53 AM   #7
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by simicrintz View Post
350 with factory 4 speed manual trans here. I can hold 75 all day long on the freeway
So what tire size and gear do you run? What RPM at 75MPH?
Keith6987 is offline   Reply With Quote
Old 02-17-2019, 10:57 PM   #8
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by SeventyOne View Post
The 700r4 needs either a new output shaft or an adapter to mate to the NP205.

If you get the new output shaft it bolts up just like your TH350 would. The other thing when you put in a 700r4 the trans is 1-7/8" longer than a TH350 so you need to either move the engine forward (my choice) or the tcase back.

I'd imagine the SM465 would bolt right in assuming you have the right crossmembers and such. The SM465 came in these as a stock option right?
I am leaning toward the sm465. There are a lot of them around and they are fairly easy to rebuild.
Keith6987 is offline   Reply With Quote
Old 02-12-2019, 12:39 AM   #9
OldCreek
Registered User
 
OldCreek's Avatar
 
Join Date: Jan 2007
Location: Central Coast California
Posts: 1,026
Re: Enginge/Trans opinions

I did the LS/4l60e swap. But....

Because its not a daily driver I've come to realize the LS and Overdrive tranny aren't really necessary. What do I care what mileage I get? Even with the LS and overdrive tranny I still only get about 12mpg....top off, 4" lift, 35" tires and 4.11 gearing (4.56 would probably be better.) What's the overdrive doing for me? Not much I figure.

Don't get me wrong. It's a cool thing to have and show people the swap. But it's not a must.

A really clean engine compartment with a carbed 350 or 454 would be just as cool!

If I were to do it again.... probably a 454 (or 383 for easy tranny mating.)

Keep the th350 or get a 700r and buy a cheap ($50) adapter to mate it to the np205. I like cruising and saving the work from shifting.

Wil
__________________
1972 K20 Suburban 5.7/700r4/NP205 Dana 44/H052 Sold
1972 C10 5.3L/4L60E 12bolt 5Lug - Sold
1971 K5 Blazer 6.0L LQ9 4L60E NP205 Dana 44/H052!!!
1970 K3500 1ton CrewCab 8.1L/Allison1000/NP205 Dana 60/14B!!!! - Sold
1984 K10 SWB 7.4L/4L80e/NP208 Corp 10/12 bolt Sold
1988 V30 CCLB 7.4L/TH400/NP205/Dana 60/Dana 70/3.73!!! (Sold)
2003 K2500HD 8.1/Allison1000/NP263
OldCreek is offline   Reply With Quote
Old 02-12-2019, 09:12 AM   #10
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,709
Re: Enginge/Trans opinions

I would go the SM465 route. They are relatively inexpensive, common and robust. The granny gear gives you plenty of grunt down low to get moving if you pull a boat or something and lets you move slowly off road. It will keep the rpm down 10% or so compared to the TH350 as well.
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Old 02-17-2019, 10:53 PM   #11
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by OldCreek View Post
I did the LS/4l60e swap. But....

Because its not a daily driver I've come to realize the LS and Overdrive tranny aren't really necessary. What do I care what mileage I get? Even with the LS and overdrive tranny I still only get about 12mpg....top off, 4" lift, 35" tires and 4.11 gearing (4.56 would probably be better.) What's the overdrive doing for me? Not much I figure.

Don't get me wrong. It's a cool thing to have and show people the swap. But it's not a must.

A really clean engine compartment with a carbed 350 or 454 would be just as cool!

If I were to do it again.... probably a 454 (or 383 for easy tranny mating.)

Keep the th350 or get a 700r and buy a cheap ($50) adapter to mate it to the np205. I like cruising and saving the work from shifting.

Wil
Thanks for the advice.
Keith6987 is offline   Reply With Quote
Old 02-17-2019, 09:20 PM   #12
Blazerowner
Senior Member
 
Blazerowner's Avatar
 
Join Date: Apr 2006
Location: Yuba City, Ca
Posts: 1,919
Re: Enginge/Trans opinions

I just sold a sm465 for 300 for everything so they are out there for cheap. I went with an ls3 and 4l80 so I can’t say I was staying with the cheap route for my build. The 4l80 bolted up to the 205 case with an adapter and 32 spline input. I’m going a little crazy for a driver.
__________________
Kirk
72 Blazer CST 4wd highlander
66 Nova
Blazerowner is offline   Reply With Quote
Old 02-17-2019, 10:46 PM   #13
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by Blazerowner View Post
I just sold a sm465 for 300 for everything so they are out there for cheap. I went with an ls3 and 4l80 so I can’t say I was staying with the cheap route for my build. The 4l80 bolted up to the 205 case with an adapter and 32 spline input. I’m going a little crazy for a driver.
Did you drive it with the 4 speed? Why did you take it out?

Last edited by Keith6987; 02-17-2019 at 10:47 PM. Reason: typo
Keith6987 is offline   Reply With Quote
Old 02-21-2019, 08:11 AM   #14
scott123
Registered User
 
Join Date: Dec 2007
Location: Middleburg, North Carolina
Posts: 462
Re: Enginge/Trans opinions

I wish we were closer. I have a SM465/NP205 that came with the Blazer when I bought it.

My 72 Blazer has the same set up.

I have always been an automatic guy with the old trucks. I switched my 69 to a 350/205 from a 3spd/Rockwell T-221.

I enjoy the 4 speed I have now but would prefer the automatic. My son, and all my friends say the 4 speed is the way to go.

It is a 'to each his own' type thing. It is a personal preference and personal use debate.

Best of luck.

If you happen to be in NC and happen to have it in the back of the truck, drop me a line.

Best of luck.

Scott
scott123 is offline   Reply With Quote
Old 02-21-2019, 02:00 PM   #15
cleszkie
Registered User
 
cleszkie's Avatar
 
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
Re: Enginge/Trans opinions

Everyone will have their own opinion on what drivetrain combo is best. Here is what I run and why:

SM465/NP205/Gear Vendors OD setup behind a fuel injected 400 SBC - I tow heavy trailers and do a lot of travel in very remote areas so the SM465 is bombproof and will get you home every time. Yes it shifts like a dump truck. So it is definitely an acquired taste. The granny low is great for slow 4x4 ascents and for getting you moving from a stop with a heavy trailer. The NP205 is a bombproof cast iron gear driven case. Nuff said. The Gear Vendors gives me overdrive and allows me to split every forward gear. This allows me to cruise at 80mph and keep my engine in its rpm sweet spot while towing up mountain passes. I went with an EFI 400 SBC and not an LS because I can work on a SBC and know them inside out. I can't say that about an LS.

I should note that I run 4.10 gears with a 35 inch tire. This combo works perfectly with the overdrive, and allows me to run 4th gear non-OD on the highway when traffic speeds are lower. I personally think that 4.56 gears will be a tad too deep to get the full advantage of an overdrive if you want to cruise 75-80 mph with low rpms.
cleszkie is offline   Reply With Quote
Old 02-21-2019, 05:02 PM   #16
scott123
Registered User
 
Join Date: Dec 2007
Location: Middleburg, North Carolina
Posts: 462
Re: Enginge/Trans opinions

I'm on 33's with 4.11's with the 355/465 and it is a tad much on the highway but I do not put that many highway miles on it anyway.

I live relatively close to the lake so towing is for short distances. And the low gear is one that will pull hell up off its hinges.

Like it has been said, it is all dependent upon personal preference and what the truck/blazer will be used for.

I prefer the automatic but that is just me. I have friends that think I am crazy for even thinking of the swap.

Scott
scott123 is offline   Reply With Quote
Old 02-21-2019, 06:02 PM   #17
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by scott123 View Post
I'm on 33's with 4.11's with the 355/465 and it is a tad much on the highway but I do not put that many highway miles on it anyway.

I live relatively close to the lake so towing is for short distances. And the low gear is one that will pull hell up off its hinges.

Like it has been said, it is all dependent upon personal preference and what the truck/blazer will be used for.

I prefer the automatic but that is just me. I have friends that think I am crazy for even thinking of the swap.

Scott
So you think the rpm is too much? if my chart is right you should be running 2700 rpm @65 mph. Is that about right?
Keith6987 is offline   Reply With Quote
Old 02-21-2019, 09:54 PM   #18
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Re: Enginge/Trans opinions

Quote:
Originally Posted by cleszkie View Post
Everyone will have their own opinion on what drivetrain combo is best. Here is what I run and why:

SM465/NP205/Gear Vendors OD setup behind a fuel injected 400 SBC - I tow heavy trailers and do a lot of travel in very remote areas so the SM465 is bombproof and will get you home every time. Yes it shifts like a dump truck. So it is definitely an acquired taste. The granny low is great for slow 4x4 ascents and for getting you moving from a stop with a heavy trailer. The NP205 is a bombproof cast iron gear driven case. Nuff said. The Gear Vendors gives me overdrive and allows me to split every forward gear. This allows me to cruise at 80mph and keep my engine in its rpm sweet spot while towing up mountain passes. I went with an EFI 400 SBC and not an LS because I can work on a SBC and know them inside out. I can't say that about an LS.

I should note that I run 4.10 gears with a 35 inch tire. This combo works perfectly with the overdrive, and allows me to run 4th gear non-OD on the highway when traffic speeds are lower. I personally think that 4.56 gears will be a tad too deep to get the full advantage of an overdrive if you want to cruise 75-80 mph with low rpms.
Thank for your input. At one point I had decided to go with a 700r4. I figured the 4:56 would give me the range to go either 35 or 37” tires and keep rpm around 2500 at 65. I don’t have a problem with changing them again to a 4:10 if that will work better with the sm465. I just can’t get the idea of a 4 speed out of my mind. I want a Blazer that looks and feels like an “old” truck. I mostly drive around on the gravel country roads and rarely go over 55 mph. LSs are great I have one in my daily driver, but I want to open the hood and have something that is “somewhat” era correct. Engines are not my strong point , but I have some experience with a basic small block.
Keith6987 is offline   Reply With Quote
Old 02-22-2019, 02:25 PM   #19
cleszkie
Registered User
 
cleszkie's Avatar
 
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
Re: Enginge/Trans opinions

Quote:
Originally Posted by Keith6987 View Post
Thank for your input. At one point I had decided to go with a 700r4. I figured the 4:56 would give me the range to go either 35 or 37” tires and keep rpm around 2500 at 65. I don’t have a problem with changing them again to a 4:10 if that will work better with the sm465. I just can’t get the idea of a 4 speed out of my mind. I want a Blazer that looks and feels like an “old” truck. I mostly drive around on the gravel country roads and rarely go over 55 mph. LSs are great I have one in my daily driver, but I want to open the hood and have something that is “somewhat” era correct. Engines are not my strong point , but I have some experience with a basic small block.
When you do your rpm calculations you need to consider that an automatic transmission may be turning a few more hundred rpms than a manual transmission at the same speed driven. Manual transmissions have a solid link to the engine's crankshaft so they turn at the exact same rate as the crank. Automatic transmissions are linked to the crankshaft via torque converter and friction belts that can allow for "slippage". I guess if you have an auto transmission with a positive lock up on the torque converter this slippage can be eliminated. But I thought I would just bring it up.
cleszkie is offline   Reply With Quote
Old 02-21-2019, 07:12 PM   #20
scott123
Registered User
 
Join Date: Dec 2007
Location: Middleburg, North Carolina
Posts: 462
Re: Enginge/Trans opinions

For me, it sounds like a lot.

It has rained here all week and have yet to put the top back on mine.

It is suppose to be clear on Monday.

I have never really noticed the actual RPM's on the highway. It sounds and feels like I'm turning a little hard.

With the 33's and 4.11's I can pull off in 2nd gear as easy as most trucks can pull off in their first gear, that part makes it feel a little tall.

Scott
scott123 is offline   Reply With Quote
Old 02-21-2019, 09:23 PM   #21
cleszkie
Registered User
 
cleszkie's Avatar
 
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
Re: Enginge/Trans opinions

I should add that "highway cruising speed" is definitely different depending which state you are in. When I lived in Maryland, the speed limit was 55 mph and the brave would cruise at 65 mph. I live in southern California now and the speed limit is 65 mph. Normal cruising speed is 75+ mph. But there are always people passing you doing 80+ mph!
cleszkie is offline   Reply With Quote
Old 02-21-2019, 10:48 PM   #22
simicrintz
Registered User
 
Join Date: Dec 2017
Location: Escondido
Posts: 305
Re: Enginge/Trans opinions

I agree that an LS engine would be awesome, but there just is something to say about and old rig with an old engine
Attached Images
 
__________________
-Bruce
1971 K5 Blazer 4WD
simicrintz is offline   Reply With Quote
Old 02-21-2019, 10:59 PM   #23
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Thumbs up Re: Enginge/Trans opinions

Quote:
Originally Posted by simicrintz View Post
I agree that an LS engine would be awesome, but there just is something to say about and old rig with an old engine
Very cool.
Keith6987 is offline   Reply With Quote
Old 02-23-2019, 12:35 AM   #24
Keith6987
Registered User
 
Join Date: Aug 2015
Location: Minier, IL.
Posts: 96
Smile Re: Enginge/Trans opinions

Well , I found a sm465/np205 that was pulled out of a 69 chevy truck. It has all the clutch linkage and cross pivot pieces with it. Cleaning it up should give me something to do while I decide if i'm going to use it. I'm sure I can rebuild them both, I mean I have watched a couple Youtube videos. Ha.
Attached Images
 
Keith6987 is offline   Reply With Quote
Old 02-25-2019, 06:54 PM   #25
cleszkie
Registered User
 
cleszkie's Avatar
 
Join Date: Feb 2003
Location: Santa Ana, CA
Posts: 2,191
Re: Enginge/Trans opinions

Quote:
Originally Posted by Keith6987 View Post
Well , I found a sm465/np205 that was pulled out of a 69 chevy truck. It has all the clutch linkage and cross pivot pieces with it. Cleaning it up should give me something to do while I decide if i'm going to use it. I'm sure I can rebuild them both, I mean I have watched a couple Youtube videos. Ha.
Looks like you got the short throw shifter option there!
cleszkie is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:26 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com