The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-04-2017, 11:57 AM   #1
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Steering column bracket

I need the steering column bracket that fits under the dash, I have been through manuals and all over the internet. Does anyone have any information??
Scurvy is offline   Reply With Quote
Old 01-04-2017, 01:26 PM   #2
Andy4639
Old member
 
Andy4639's Avatar
 
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
Thumbs up Re: Steering column bracket

Here you go. A picture of the 3 brackets under the column. thanks to LOCDOC! A junkyard is going to be your best bet though!
The bracket shouldn't be to hard to make. Flat stock wrapped around the column with bolt holes.


__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver
Seeing the USA in a 71


Upstate SC GM Truck Club
2013,14 and 2016 Hot Rod Pour Tour


http://upstategmtrucks.com/



Get out and drive the truck this summer and have some fun!
It sucks not being able to hear!

LWB trucks rule, if you don't think so measure your SWB!
After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.
Andy4639 is offline   Reply With Quote
Old 01-04-2017, 01:39 PM   #3
LockDoc
The Older Generation

 
LockDoc's Avatar
 
Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 25,270
Re: Steering column bracket

-
Thanks Andy!

The small narrow bracket goes in first and is the one that actually holds the column to the dash. It uses two 5/16 x 1 inch bolts. It is different on the ends so make sure you have it installed correctly. The large one is the pedal stop plate and has two small square holes in it for the pedal bumpers. It uses four 5/16 x 3/4 inch bolts. The fancy one is the trim plate for the gap between the column and dash. It fits over the rubber gasket. It has two #8 or #10 (can't remember for sure) x 3/4 pan head sheet metal screws....

Like Andy said, salvage yard if you have any close. If not check on the parts board on here. Anyone that parts trucks on there will have what you need.

LockDoc
__________________
Leon

Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles

(My Dually Pickup Project Thread)

http://67-72chevytrucks.com/vboard/s...d.php?t=829820

-
LockDoc is offline   Reply With Quote
Old 01-04-2017, 03:11 PM   #4
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Quote:
Originally Posted by LockDoc View Post
-
Thanks Andy!

The small narrow bracket goes in first and is the one that actually holds the column to the dash. It uses two 5/16 x 1 inch bolts. It is different on the ends so make sure you have it installed correctly. The large one is the pedal stop plate and has two small square holes in it for the pedal bumpers. It uses four 5/16 x 3/4 inch bolts. The fancy one is the trim plate for the gap between the column and dash. It fits over the rubber gasket. It has two #8 or #10 (can't remember for sure) x 3/4 pan head sheet metal screws....

Like Andy said, salvage yard if you have any close. If not check on the parts board on here. Anyone that parts trucks on there will have what you need.

LockDoc
Posted via Mobile Device
Scurvy is offline   Reply With Quote
Old 01-04-2017, 03:12 PM   #5
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Re: Steering column bracket

Thanks for the prompt reply!!
Posted via Mobile Device
Scurvy is offline   Reply With Quote
Old 01-04-2017, 03:33 PM   #6
biketopia
Senior Member
 
Join Date: Jul 2015
Location: Warrenton VA
Posts: 1,001
Re: Steering column bracket

I might have those pieces in my stash of parts
__________________
71 c-10 Long Bed, under the knife for a No Limit Engineering Wide Ride Chassis Pack and coil over static drop.

07 Silverado Classic 2wd

95 Camaro 427SBC/TH350
biketopia is offline   Reply With Quote
Old 01-04-2017, 03:49 PM   #7
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

try a wrecking yard, if no luck I may have what you need,do you need all 3 parts?
El Dorado Jim is offline   Reply With Quote
Old 01-04-2017, 05:04 PM   #8
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Re: Steering column bracket

Please check, Ill take em if you got em.
Scurvy is offline   Reply With Quote
Old 01-04-2017, 07:08 PM   #9
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

Quote:
Originally Posted by Scurvy View Post
Please check, Ill take em if you got em.
do you need all three pieces? I have all three
El Dorado Jim is offline   Reply With Quote
Old 01-04-2017, 07:26 PM   #10
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Re: Steering column bracket

Yes please.
Scurvy is offline   Reply With Quote
Old 01-04-2017, 10:27 PM   #11
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

Quote:
Originally Posted by Scurvy View Post
Yes please.
I will check and see how much shipping is to Bakersfield, you have the bracket that bolts to the firewall on the engine side?
El Dorado Jim is offline   Reply With Quote
Old 01-04-2017, 10:34 PM   #12
Scurvy
Registered User
 
Scurvy's Avatar
 
Join Date: Jan 2017
Location: Bakersfield
Posts: 11
Re: Steering column bracket

that's the only one I have. What other stuff do you have??
Scurvy is offline   Reply With Quote
Old 01-04-2017, 10:43 PM   #13
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

I parted out a truck years ago and have some interior stuff, what do you need...my wife says it will cost around $13.00 to ship it to you, I only want the cost of shipping, send me $15.00 and we will call it good, pm me and i will get your name and address, and you mine
El Dorado Jim is offline   Reply With Quote
Old 01-04-2017, 11:04 PM   #14
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

pm 'ed you back
El Dorado Jim is offline   Reply With Quote
Old 01-05-2017, 03:43 PM   #15
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

Hey Scurvy, since you are a new member here, not sure if you know about lmc truck and truckandcarshops, good places to buy aftermarket parts, there are others also. http://www.lmctruck.com/chevrolet/ http://www.truckandcarshop.com/6072.html
El Dorado Jim is offline   Reply With Quote
Old 03-28-2017, 08:36 PM   #16
Mhussnatter
Registered User
 
Join Date: Jun 2016
Location: Easton, MD
Posts: 63
Re: Steering column bracket

Sorry to revive this old thread from back in January but I am in need of these parts. I have a 1969 C10 and The previous owner of my truck ripped out all of the steering column brackets and jammed a mid 80's van column in the truck and rigged it up bad. I have taken it out and installed an IDIDIT column but unfortunately can not mount it at the dash because everything is missing. I have been searching vendor websites and can not find these parts can anyone point me in the right direction?
Mhussnatter is offline   Reply With Quote
Old 03-30-2017, 01:55 AM   #17
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

wrecking yards are your best bet or check the parts for sale board on this site,I dont think I have any more of these parts,but Im going to pick n pull Friday,will take a look for you
El Dorado Jim is offline   Reply With Quote
Old 03-30-2017, 07:32 PM   #18
Mhussnatter
Registered User
 
Join Date: Jun 2016
Location: Easton, MD
Posts: 63
Re: Steering column bracket

El Dorada Jim Thanks buddy I truly wish it were that easy but unfortunately for me there are NO salvage yards at all where I live. There are a couple just over an hour or so away but none of them have any 67-72 trucks
Mhussnatter is offline   Reply With Quote
Old 03-31-2017, 12:35 AM   #19
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

I went to four pick n pulls today instead of tomorrow and not one 67-72 truck at any of them....I have a business card of a guy in Sacramento that parts these old trucks out, I will look for it tomorrow and give you his name and number...he will definitely have the parts you need...Jim
El Dorado Jim is offline   Reply With Quote
Old 04-01-2017, 02:24 AM   #20
El Dorado Jim
Registered User
 
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
Re: Steering column bracket

didnt have time today to look, will look tomorrow for the number of the guy in Sac that has the parts..
El Dorado Jim is offline   Reply With Quote
Old 04-01-2017, 07:05 AM   #21
Mhussnatter
Registered User
 
Join Date: Jun 2016
Location: Easton, MD
Posts: 63
Re: Steering column bracket

Thanks anyway Jim but I got what I need now. One of the other members was able to find for me at a salvage yard. Thanks
Mhussnatter is offline   Reply With Quote
Old 10-15-2022, 03:56 PM   #22
Gib74
Registered User
 
Join Date: May 2022
Location: Redding
Posts: 12
Re: Steering column bracket

Bringing back an oldie post. Any chance anyone has the halfmoon clamp? This is the clamp on the left in Andy4639 picture. Thanks guys and I'm a newbie first time poster as well.
Gib74 is offline   Reply With Quote
Old 10-15-2022, 05:58 PM   #23
Jason Banks
Senior Member
 
Jason Banks's Avatar
 
Join Date: Dec 1999
Location: TX
Posts: 1,487
Re: Steering column bracket

I'm sure the moderators will be along to tell you, you need to be a supporting member to post a WTB (want to buy). To become a supporting member there's a link at the top of the page that says "Subscribe" it takes you to: https://67-72chevytrucks.com/vboard/payments.php

Back to your question. I would call Bill and see if he has one - https://www.facebook.com/ChevymanBill/

Or Tremayne
https://www.facebook.com/people/Trem...0057753605935/
Jason Banks is offline   Reply With Quote
Reply

Bookmarks

Tags
steering column, steering column bracket

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:38 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com