Project "Jezebel" - Page 16 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rsmarr1982 · 03-22-2013, 09:44 PM

wow!!! thats a work of art!

sgaylord · 03-26-2013, 01:18 PM

Quote:

Hart_Rod
Re: Project "Jezebel"
I think you having it on jack stands is causing part of the problem. Bolt the front wheels on and put it on the ground and recheck. You may still have to add a few shims, but I bet it is closer.
Posted via Mobile Device

Rob, I tried your suggestion and took it down from the jack stands and let it set on the wheels. While this helped some I still have about a 1/2 gap between the lines in the cab vs. bed.

I received the new cab mounts and the rears in the new kit are about 1/4" taller than the fronts. I installed the new cab mounts and will have to add shims to get the cab inline with the bed.

Quote:

brn agn
Re: Project "Jezebel"
This might not be of any help, but I just purchased new bushings from Brother's. The front mounts are 1-7/16" tall and the rears are 1-1/4". I will be installing them this weekend. There also looks to be at least one additional steel washer (approximately 1/8" thick) in between my old bushings and the cab.

Thanks for the reply. Are you saying your front mounts are taller than the rears? The instructions I have with my new mounts show it the other way around. I will verify I didn't read my instructions incorrectly.

Quote:

rsmarr1982
Re: Project "Jezebel"
wow!!! thats a work of art!

Thanks

brn agn · 03-26-2013, 03:42 PM

Quote:

Originally Posted by sgaylord

Thanks for the reply. Are you saying your front mounts are taller than the rears? The instructions I have with my new mounts show it the other way around. I will verify I didn't read my instructions incorrectly.
Thanks

That is correct. However, there are 2 items to note: 1) Instructions were not included with mine and I determined which bushings where the front based on the larger inner diameter thru hole and how they matched the bushings I removed. 2) I had to shim the rear bushings approximately 1/8" in order for the cab to line up with the bed. Now I am questioning if the front and rear bushings should be swapped for one another. Hmmmm.... It will be interesting to see the bushings from Classic Parts work out.

sgaylord · 03-26-2013, 03:47 PM

Quite a bit of progress but a lot more still to be done.

Dynamat
Willwood master cylinder and proportioning valve
Brake lines
Rear 95 Impala SS brakes
Boyd's Tank and SS fuel line
American AutoWire harness
Dakota Digital VHX dash, AC Controller, and Gear selector
Vintage Air Gen IV
Holley Fuel pump and Street Avenger carb
Early Classic Drop Spindles and tranny cross-member
Anti-sway bar and prothane bushings
Third brake light (55 Chevy)
Champion Monster 4 core aluminum radiator w/dual fans

Upholstery guy says the upholstery will be done tomorrow. We will see.

Here are some pics (some show the work in progress). If there are any area's you want more pics on, let me know.

Since I didn't want to bolt anything to the firewall I made this bracket to bolt the evap to. It's screwed into the cowl at the top and behind a bracket on the toe board.
Name: 20130317_134325.jpg
Views: 953
Size: 30.5 KB

Name: 20130317_134325.jpg
Views: 953
Size: 30.5 KB

Dakota Digital boxes
Name: 20130317_180026.jpg
Views: 949
Size: 32.9 KB

Spaghetti anyone?

Name: 20130325_213950.jpg
Views: 951
Size: 41.0 KB

Master and brake lines
Name: 20130325_213940.jpg
Views: 945
Size: 31.8 KB

AC and Heater hoses in progress
Name: 20130325_213905.jpg
Views: 938
Size: 49.1 KB

**Hart_Rod** · 03-26-2013, 03:53 PM

Looks great! Do you have and rubber bushings under the bed mounts?

sgaylord · 03-26-2013, 03:57 PM

Quote:

Hart_Rod
Re: Project "Jezebel"
Looks great! Do you have and rubber bushings under the bed mounts?

I did have the 1/4 round rubber isolators. I took them out but may have to come up with something to replace them with.

mjensen · 03-26-2013, 08:18 PM

Friggin sweet!

sgaylord · 04-02-2013, 08:43 AM

Making some progress, though not as much as I would like.

Wiring almost complete.

Flaming river polished stainless steering column installed.

Lokar mechanical shifter installed

Dakota Digital VHX gauges installed

Dakota Digital VA controller installed. Although the display is red and I ordered blue.... The box even listed it as blue. I'll have to call and swap it out.

Glass installed

Sanderson headers installed

Bed and cab bolted down. It took a half inch of shims to level the rear of the cab. I may have to add more shims when I install the front sheet metal.

Picked up he interior from the upholstery shop. Let me know what you think.

Started the engine.

Here are some pics. It will take a few posts to upload them unless if someone can tell me why I can't upload but one pic as a time via this iPad....

Name: image.jpg
Views: 889
Size: 58.2 KB

Posted via Mobile Device
Posted via Mobile Device

sgaylord · 04-02-2013, 08:44 AM

Name: image.jpg
Views: 891
Size: 51.0 KB

Posted via Mobile Device
Posted via Mobile Device

sgaylord · 04-02-2013, 08:45 AM

Name: image.jpg
Views: 922
Size: 41.0 KB

Posted via Mobile Device
Posted via Mobile Device

sgaylord · 04-02-2013, 08:46 AM

Name: image.jpg
Views: 964
Size: 30.1 KB

Posted via Mobile Device
Posted via Mobile Device

jmedero · 04-02-2013, 09:12 AM

Really nice Steve.
Posted via Mobile Device

gdavis · 04-02-2013, 09:54 AM

Quote:

Originally Posted by sgaylord

Attachment 1086111
Posted via Mobile Device
Posted via Mobile Device

The reason you can't post but one picture at a time is. The pictures are to large. resize your pictures before trying to up load them. The site can't up load that size. I had the same problem. I contacted the site and they told me the same thing I am telling you. gdavis from Florida

gdavis · 04-02-2013, 09:56 AM

Quote:

Originally Posted by sgaylord

Attachment 1086110
Posted via Mobile Device
Posted via Mobile Device

your seat is a killer. alone with the other it will be a show stopper.

brn agn · 04-02-2013, 10:18 AM

It's coming together! Everything looks great.

mcbassin · 04-02-2013, 11:04 AM

Future show WINNER for sure! Awesome work Steve.

**67cheby** · 04-02-2013, 12:02 PM

Looking TOP NOTCH !

sgaylord · 04-02-2013, 01:16 PM

Thanks guys for the kind comments. It's great motivation!

Here is a vid of the engine. It's already broke in.

http://http://s971.photobucket.com/user/sgaylord/media/IMG_0058.mp4.html
Posted via Mobile Device

Let me know what you think.
Posted via Mobile Device

Fattback · 04-02-2013, 06:58 PM

Sounds great!!!!!!

Rob

mjensen · 04-02-2013, 11:31 PM

Show off!

Looking awesome and sounds real snappy! I think I'm going to go invest in Goodyear because I think you'll be burning through the tires on that bad boy.

mcbassin · 04-03-2013, 08:16 AM

Engine sounds great!

sourkraut · 04-03-2013, 09:59 PM

Looks great

Xeen · 04-03-2013, 10:33 PM

This project reminds me of another c10 project a friend of mine did, no rust left unfixed.
In my opinion the Quality of craftsmanship and attention to detail is top notch A #1 and with this level of restoration the truck will command top dollar when you are done.
This one deserves some serious documentation so people can see all the hard work you put into it and the level of professionalism it was treated to.

sgaylord · 04-05-2013, 01:12 PM

Thanks guys for all the comments. Here are a couple more pics for ya. I installed the front sheetmetal and she is starting to look like a truck again.

I haven't color sanded the hood yet and I still need to buff those panels that I have cut already.

Name: image.jpg
Views: 714
Size: 97.6 KB

Posted via Mobile Device
Posted via Mobile Device

sgaylord · 04-05-2013, 01:16 PM

These pics are 105k and 97k respectively so I have no ideal why this iPad will not allow me to post more than one at a time. If anyone knows how to do this please let me know.

Name: image.jpg
Views: 711
Size: 105.0 KB

Name: image.jpg
Views: 711
Size: 105.0 KB

Posted via Mobile Device
Posted via Mobile Device

03-22-2013, 09:44 PM	#376
rsmarr1982 Registered User Join Date: Jul 2010 Location: mogadore ohio Posts: 867	Re: Project "Jezebel" wow!!! thats a work of art! __________________ 1969 chevy c10 lwb stepside 250 6 3 ott 1971 chevy c10 lwb 250 6 with power steering 3 ott 1972 chevy k20 4x4 350/TH350 automatic 1978 chevy Malibu 4dr 305 2bbl (all original) 1979 chevy k10 Scottsdale 350/th350 full-time 4wd(daily driver)

03-26-2013, 03:47 PM	#379
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Quite a bit of progress but a lot more still to be done. Dynamat Willwood master cylinder and proportioning valve Brake lines Rear 95 Impala SS brakes Boyd's Tank and SS fuel line American AutoWire harness Dakota Digital VHX dash, AC Controller, and Gear selector Vintage Air Gen IV Holley Fuel pump and Street Avenger carb Early Classic Drop Spindles and tranny cross-member Anti-sway bar and prothane bushings Third brake light (55 Chevy) Champion Monster 4 core aluminum radiator w/dual fans Upholstery guy says the upholstery will be done tomorrow. We will see. Here are some pics (some show the work in progress). If there are any area's you want more pics on, let me know. Since I didn't want to bolt anything to the firewall I made this bracket to bolt the evap to. It's screwed into the cowl at the top and behind a bracket on the toe board. Dakota Digital boxes Spaghetti anyone? Master and brake lines AC and Heater hoses in progress __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

03-26-2013, 03:53 PM	#380
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,827	Re: Project "Jezebel" Looks great! Do you have and rubber bushings under the bed mounts? __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

03-26-2013, 08:18 PM	#382
mjensen Registered User Join Date: Jun 2006 Location: Utah Posts: 1,562	Re: Project "Jezebel" Friggin sweet! __________________ Mike '69 GMC 3/4 ton 4x4 Build Thread

04-02-2013, 08:43 AM	#383
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Making some progress, though not as much as I would like. Wiring almost complete. Flaming river polished stainless steering column installed. Lokar mechanical shifter installed Dakota Digital VHX gauges installed Dakota Digital VA controller installed. Although the display is red and I ordered blue.... The box even listed it as blue. I'll have to call and swap it out. Glass installed Sanderson headers installed Bed and cab bolted down. It took a half inch of shims to level the rear of the cab. I may have to add more shims when I install the front sheet metal. Picked up he interior from the upholstery shop. Let me know what you think. Started the engine. Here are some pics. It will take a few posts to upload them unless if someone can tell me why I can't upload but one pic as a time via this iPad.... Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-02-2013, 08:44 AM	#384
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-02-2013, 08:45 AM	#385
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-02-2013, 08:46 AM	#386
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-02-2013, 09:12 AM	#387
jmedero Registered User Join Date: Jun 2008 Location: pensacola fl Posts: 3,072	Re: Project "Jezebel" Really nice Steve. Posted via Mobile Device __________________ 68 BB burb build thread Scott's super slam front/rear http://67-72chevytrucks.com/vboard/s...d.php?t=378084

04-02-2013, 10:18 AM	#390
brn agn Registered User Join Date: Mar 2009 Location: Youngsville, NC Posts: 952	Re: Project "Jezebel" It's coming together! Everything looks great. __________________ 1969 C10 SWB Project Charity Case AKA "Roscoe" 1971 Cheyenne Super A Combined Effort The Service Station-A practical ministry for those in need

04-02-2013, 11:04 AM	#391
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Project "Jezebel" Future show WINNER for sure! Awesome work Steve. __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

04-02-2013, 12:02 PM	#392
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project "Jezebel" Looking TOP NOTCH ! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

04-02-2013, 01:16 PM	#393
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Thanks guys for the kind comments. It's great motivation! Here is a vid of the engine. It's already broke in. http://http://s971.photobucket.com/user/sgaylord/media/IMG_0058.mp4.html Posted via Mobile Device Let me know what you think. Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-02-2013, 06:58 PM	#394
Fattback Registered User Join Date: Sep 2010 Location: Oklahoma Posts: 287	Re: Project "Jezebel" Sounds great!!!!!! Rob

04-02-2013, 11:31 PM	#395
mjensen Registered User Join Date: Jun 2006 Location: Utah Posts: 1,562	Re: Project "Jezebel" Show off! Looking awesome and sounds real snappy! I think I'm going to go invest in Goodyear because I think you'll be burning through the tires on that bad boy. __________________ Mike '69 GMC 3/4 ton 4x4 Build Thread



Register or Log In To remove these advertisements.

04-03-2013, 08:16 AM	#396
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Project "Jezebel" Engine sounds great! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

04-03-2013, 09:59 PM	#397
sourkraut Registered User Join Date: Sep 2008 Location: WI Posts: 1,243	Re: Project "Jezebel" Looks great __________________ "The way it is" truck build http://67-72chevytrucks.com/vboard/s...d.php?t=359200

04-03-2013, 10:33 PM	#398
Xeen Registered User Join Date: Aug 2012 Location: Topeka Kansas Posts: 2,655	Re: Project "Jezebel" This project reminds me of another c10 project a friend of mine did, no rust left unfixed. In my opinion the Quality of craftsmanship and attention to detail is top notch A #1 and with this level of restoration the truck will command top dollar when you are done. This one deserves some serious documentation so people can see all the hard work you put into it and the level of professionalism it was treated to. __________________ Please call me Brian. Check out My 1972 SWB Fleetside 5.3L Vortec Restomod Build

04-05-2013, 01:12 PM	#399
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" Thanks guys for all the comments. Here are a couple more pics for ya. I installed the front sheetmetal and she is starting to look like a truck again. I haven't color sanded the hood yet and I still need to buff those panels that I have cut already. Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

04-05-2013, 01:16 PM	#400
sgaylord Project collector Join Date: Mar 2006 Location: Sanderson, Fl Posts: 700	Re: Project "Jezebel" These pics are 105k and 97k respectively so I have no ideal why this iPad will not allow me to post more than one at a time. If anyone knows how to do this please let me know. Posted via Mobile Device Posted via Mobile Device __________________ 69 CST-10 SWB (disguised as a 67) 383/700r4 Jezebel Jezebel 3.0 NEW!!! 2020 GMC 3500 Denali Duramax 2016 Harley Street Glide CVO Roll Tide!

Register or Log In To remove these advertisements.