Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
04-02-2013, 11:10 AM | #1 |
Registered User
Join Date: Jun 2012
Location: cville ga
Posts: 65
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
this is off the wheel
Posted via Mobile Device |
04-02-2013, 11:23 AM | #2 |
Amateur Rust Fighter
Join Date: Sep 2007
Location: Mankato, MN
Posts: 1,087
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
Those must be the new revision that just came out -- not even listed on the Boss site yet. Not sure why they've reverted to -1AA for the revision, unless it's because they consider the different offset a new line. That +2mm offset gets them much closer to where they should be, with about 5.6" of backspacing instead of 6.3" on the older versions with a +20mm offset. You still may need to run a 1/4" spacer, but it depends on your individual setup, rear end width, tire choice, etc. Only ways to know are to measure carefully or just bolt it up and see what happens.
For reference, these are my 20x10 specs from back in 2010: http://67-72chevytrucks.com/vboard/s...=1#post3933454
__________________
Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...) |
04-02-2013, 11:33 AM | #3 |
Registered User
Join Date: Jun 2012
Location: cville ga
Posts: 65
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
its a 4/6 drop maybe alittle more in the rear 82 shortbed factory10 bolt rear planning on a 275-35-20 rear
Posted via Mobile Device |
04-02-2013, 11:43 AM | #4 | |
TNT-MOTORSPORTS
Join Date: Mar 2008
Location: TULSA OKLAHOMA
Posts: 2,692
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
Quote:
That wheel still has the 82.80mm bore size so you will still have to mod the front rotor more than likely , unless it is a light duty rotor front which it could be on an 82. Then they will just bolt on. |
|
04-02-2013, 11:46 AM | #5 |
Registered User
Join Date: Jun 2012
Location: cville ga
Posts: 65
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
it has 1" rotors and i was wanting to stay around 28" tall but this is all new to me but all the info is greatly appreciated thanks
Posted via Mobile Device |
04-02-2013, 12:06 PM | #6 |
Amateur Rust Fighter
Join Date: Sep 2007
Location: Mankato, MN
Posts: 1,087
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
I went with 245/40-20 (27.72" tall) and 295/40-20 (29.29" tall) on my staggered 20s. I would have preferred 295/35 (28.13" tall) on the rear but it wasn't available in the tire I wanted.
__________________
Brent '72 Chevy SWB stepside - [ Build Thread ] '79 ChevMC SWB fleetside - [ Build Thread ] '64 Chevy SWB fleetside & '66 Chevy SWB stepside (waiting in the wings...) |
04-02-2013, 12:18 PM | #7 | |
TNT-MOTORSPORTS
Join Date: Mar 2008
Location: TULSA OKLAHOMA
Posts: 2,692
|
Re: Got some new wheels: Boss 338's in 20x10 and 20x8.5
Quote:
This is what I would do also. If you get on tirerack.com you can compare sizes of tires and wheel widths etc. |
|
Bookmarks |
|
|